Pioneer AVX-P8DVD Installation Manual
Pioneer avx-p8dvd: install guide
Hide thumbs
Also See for AVX-P8DVD:
- Operation manual (85 pages) ,
- Owner's manual (34 pages) ,
- Operation manual (85 pages)
Table of Contents
Advertisement
Available languages
Available languages
Quick Links
AVX-P8DVD
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Printed in Japan
Imprimé au Japon
<CRD3865-A> UC
<KMMNF> <04C00000>
Connecting the Units
CAUTION:
WARNING:
• PIONEER does not recommend that you
• To avoid the risk of accident and the
install or service your display yourself.
potential violation of applicable laws, the
Installing or servicing the product may
front DVD or TV (sold separately) fea-
expose you to risk of electric shock or
ture should never be used while the vehi-
other hazards. Refer all installation and
cle is being driven. Also, Rear Displays
servicing of your display to authorized
should not be in a location where it is a
Pioneer service personnel.
visible distraction to the driver.
• Secure all wiring with cable clamps or
• In some countries or states the viewing of
electrical tape. Do not allow any bare
images on a display inside a vehicle even
wiring to remain exposed.
by persons other than the driver may be
illegal. Where such regulations apply,
• Do not drill a hole into the engine com-
they must be obeyed and this unit's DVD
partment to connect the yellow lead of
features should not be used.
the unit to the vehicle battery. Engine
vibration may eventually cause the insu-
lation to fail at the point where the wire
passes from the passenger compartment
into the engine compartment. Take extra
care in securing the wire at this point.
• It is extremely dangerous to allow the
display lead to become wound around
the steering column or gearshift. Be sure
to install the display in such a way that it
will not obstruct driving.
• Make sure that wires will not interfere
with moving parts of the vehicle, such as
the gearshift, parking brake or seat slid-
ing mechanism.
• Do not shorten any leads. If you do, the
protection circuit may fail to work prop-
erly.
<ENGLISH>
Note:
• To prevent incorrect connection, the input side of
• This unit is for vehicles with a 12-volt battery and
the IP-BUS connector is blue, and the output side
negative grounding. Before installing it in a recre-
is black. Connect the connectors of the same
ational vehicle, truck, or bus, check the battery
colors correctly.
voltage.
• If this unit is installed in a vehicle that does not
• To avoid shorts in the electrical system, be sure to
have an ACC (accessory) position on the ignition
disconnect the ≠ battery cable before beginning
switch, the red lead of the unit should be connected
to a terminal coupled with ignition switch ON/OFF
installation.
operations. If this is not done, the vehicle battery
• Refer to the owner's manual for details on
may be drained when you are away from the vehi-
connecting the power amp and other units, then
make connections correctly.
cle for several hours. (Fig. 1)
• Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
• Route and secure all wiring so it cannot touch any
moving parts, such as the gear shift, handbrake and
seat rails. Do not route wiring in places that get
hot, such as near the heater outlet. If the insulation
of the wiring melts or gets torn, there is a danger of
the wiring short-circuiting to the vehicle body.
ACC position
No ACC position
• Don't pass the yellow lead through a hole into the
engine compartment to connect to the battery. This
will damage the lead insulation and cause a very
dangerous short.
• Do not shorten any leads. If you do, the protection
circuit may fail to work when it should.
• Cords for this product and those for other products
• Never feed power to other equipment by cutting
may be different colors even if they have the same
the insulation of the power supply lead of the unit
function. When connecting this product to another
and tapping into the lead. The current capacity of
product, refer to the supplied manuals of both
the lead will be exceeded, causing overheating.
products and connect cords that have the same
• When replacing fuse, be sure to use only fuse of
function.
the rating prescribed on the fuse holder.
• If the RCA pin jack on the unit will not be used, do
not remove the caps attached to the end of the con-
nector.
Fig. 1
Advertisement
Table of Contents
Related Manuals for Pioneer AVX-P8DVD
Summary of Contents for Pioneer AVX-P8DVD
- Page 1 Connecting the Units CAUTION: • PIONEER does not recommend that you install or service your display yourself. Installing or servicing the product may expose you to risk of electric shock or other hazards. Refer all installation and servicing of your display to authorized Pioneer service personnel.
-
Page 2: Connecting The Units
Rear video output (REAR VIDEO OUTPUT) Rear audio output (REAR AUDIO OUTPUT) 15 cm (5-7/8 in.) Audio output (AUDIO OUTPUT) When connecting with a Pioneer head unit WARNING AV-BUS input (Blue) Blue Connection method Blue Clamp the lead. 2. Clamp firmly with needle-nosed pliers. -
Page 3: When Connecting With A Multi-Channel Processor
When connecting the external video component and the display This product This product CAUTION CAUTION Pioneer recommends the use of Pioneer recommends the use of a camera which outputs mirror a camera which outputs mirror reversed images, otherwise reversed images, otherwise... -
Page 4: Installation
IP-BUS mode (S) and the ADD-ON mode (M). Switch the mode according to the combined components. • IP-BUS mode (S) – Using with a Pioneer head unit featuring an IP- BUS input or multi-channel proces- Dashboard or sor control unit Console •... -
Page 5: Raccordements Des Appareils
12 V, avec pôle négatif à la masse. Avant de l’installer dans un véhicule de loisir, un • PIONEER ne vous recommande pas • Pour éviter tout risque d’accident, et camion ou un car, vérifier la tension de la batterie. -
Page 6: Branchement Du Cordon D'alimentation
(REAR AUDIO OUTPUT) 15 cm Sortie audio (AUDIO OUTPUT) Lors du raccordement à un appareil central Pioneer AVERTISSEMENT LE FIL VERT CLAIR SUR LE CONNECTEUR D’ALIMENTATION A POUR BUT DE DETECTER L’ETAT DE STATIONNEMENT DU VEHICULE ET DOIT ETRE CONNECTE AU COTE ALIMENTATION DU Entrée AV-BUS (Bleu) -
Page 7: Lors Du Raccordement D'un Processeur Multi-Canaux
Elle ne doit pas être utilisée à des fins de divertisse- ment. Raccordements à un appareil vidéo externe et à un écran Cet appareil ATTENTION Pioneer conseille l’utilisation d’une caméra qui fournit des images inversées, comme dans un miroir, faute de quoi les images apparaissant sur l’écran seront inversées. - Page 8 ADD-ON (M). Changez de mode en fonction de la combinaison des composants. • Mode IP-BUS (S) – Utiliser ce mode avec un appareil central Pioneer dis- Tableau de bord posant d’une entrée IP-BUS ou d’une ou console unité de contrôle à processeur multi-...