Pioneer DEH-P3000IB Installation Manual
Pioneer deh-p3000ib: install guide
Hide thumbs
Also See for DEH-P3000IB:
- Operation manual (111 pages) ,
- Installation manual (7 pages) ,
- Operation manual (65 pages)
Advertisement
Available languages
Available languages
DEH-P3000IB
Printed in China
Imprimé en Chine
<CRD4246-A/S> UC
<KOKNX> <07H00000>
Installation
English
3. Install the unit as illustrated.
Note
Mounting sleeve
Dashboard
• Check all connections and systems before final in-
stallation.
182
1 1 1 82
• Do not use unauthorized parts. The use of unau-
thorized parts may cause malfunctions.
53
53
Rubber bush
• Consult with your dealer if installation requires drill-
ing of holes or other modifications of the vehicle.
• Do not install this unit where:
— it may interfere with operation of the vehicle.
Screw
— it may cause injury to a passenger as a result
of a sudden stop.
• The semiconductor laser will be damaged if it over-
heats. Install this unit away from hot places such as
near the heater outlet.
Removing the Unit
• Optimum performance is obtained when the unit is
installed at an angle of less than 60°.
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring. When reattaching the trim ring,
60°
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
DIN Front/Rear-mount
• It becomes easy to remove the trim ring if the
front panel is released.
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
Trim ring
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
DIN Front-mount
2. Insert the supplied extraction keys
Installation with the rubber bush
into both sides of the unit until they
1. Insert the mounting sleeve into the
click into place.
dashboard.
• When installing in a shallow space, use a
supplied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by
using a screwdriver to bend the
metal tabs (90°) into place.
3. Pull the unit out of the dashboard.
Installation
English
Fastening the front panel
DIN Rear-mount
If you do not plan to detach the front panel,
1. Extend top and bottom of the trim
the front panel can be fastened with supplied
ring outwards to remove the trim
screw.
ring. When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
Screw
• It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
2. Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
3. Tighten two screws on each side.
• Use either truss screws (5 mm × 8 mm) or
flush surface screws (5 mm × 9 mm), depend-
ing on the shape of screw holes in the bracket.
Screw
Dashboard or Console
Factory radio mounting bracket
Connecting the unit
English
• Control signal is output through blue/white cable
Note
when this unit is powered on. Connect it to an ex-
ternal power amp's system remote control or the
• When this unit is installed in a vehicle without
vehicle's auto-antenna relay control terminal (max.
ACC (accessory) position on the ignition switch,
300 mA, 12 V DC). If the vehicle is equipped with a
red cable must be wired to the terminal that can
glass antenna, connect it to the antenna booster
detect the operation of the ignition key. Otherwise,
power supply terminal.
battery drain may result.
• Never connect blue/white cable to external power
amp's power terminal. Also, never connect it to
the power terminal of the auto antenna. Other-
wise, battery drain or malfunction may result.
• IP-BUS connectors are color-coded. Be sure to
connect connectors of the same color.
• Black cable is ground. This cable and other
product's ground cable (especially, high-current
products such as power amp) must be wired sepa-
ACC position
No ACC position
rately. Otherwise, fire or malfunction may result if
they are accidentally detached.
• Use this unit in other than the following condi-
tions could result in fire or malfunction.
— Vehicles with a 12-volt battery and negative
grounding.
— Speakers with 50 W (output value) and 4 ohm
to 8 ohm (impedance value).
• To prevent short-circuit, overheating or malfunc-
tion, be sure to follow the directions below.
— Disconnect the negative terminal of the battery
before installation.
— Secure the wiring with cable clamps or adhe-
sive tape. To protect the wiring, wrap adhesive
tape around them where they lie against metal
parts.
— Place all cables away from moving parts, such
as gear shift and seat rails.
— Place all cables away from hot places, such as
near the heater outlet.
— Do not pass the yellow cable through a hole
into the engine compartment to connect to a
battery.
— Cover any disconnected cable connectors with
insulating tape.
— Do not shorten any cables.
— Never cut the insulation of the power cable of
this unit in order to share the power to other
equipment. Current capacity of the cable is
limited.
— Use a fuse of the rating prescribed.
— Never wire the speaker negative cable directly
to ground.
— Never band together multiple speaker's nega-
tive cables.
Advertisement
Related Manuals for Pioneer DEH-P3000IB
Summary of Contents for Pioneer DEH-P3000IB
- Page 1 • The semiconductor laser will be damaged if it over- heats. Install this unit away from hot places such as DEH-P3000IB near the heater outlet. • Optimum performance is obtained when the unit is installed at an angle of less than 60°.
- Page 2 Connecting the unit English Connecting the unit When not connecting a rear speaker leard to a subwoofer iPod with Dock Dock connector port Connector Dock connector Interface cable (e.g., CD-I200) (sold separately) Gray 2 m (6 ft. 7 in.) Front output This product Rear output or subwoofer output...
- Page 3 Installation Français Installation 3. Installez l’appareil comme montré 2. Insérez les clés d’extraction Remarque sur l’illustration. • Vérifiez toutes les connexions et tous les systèmes Manchon de montage Tableau de bord avant l’installation finale. • N’utilisez aucune pièce non autorisée.L’utilisation de pièces non autorisées peut causerun mauvais 1 1 1 82 fonctionnement.
- Page 4 Connexions des appareils Français Connexions des appareils Quand aucun câble d’enceinte arrière n’est connecté au caisson de grave iPod avec Port de connexion Dock connecteur Dock Connecteur Dock Câble d’interface (par ex., CD-I200) (vendu séparément) Gris Sortie avant Cet appareil Sortie arrière ou sortie du caisson de grave Prise d’antenne...