Related Manuals for Toro 03731
Summary of Contents for Toro 03731
- Page 1 Form No. 3407-884 Rev A 27-inch Verticutter Reelmaster ® 7000-D Cutting Unit Model No. 03731—Serial No. 400000000 and Up *3407-884* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Safety and Instructional Decals ......... 3 Setup ................4 You may contact Toro directly at www.Toro.com for product 1 Inspecting the Verticutter........5 and accessory information, help finding a dealer, or to register 2 Installing the Transport Rollers ....... 5 your product. -
Page 3: Safety
• To ensure optimum performance and continued safety influence of drugs or alcohol. certification of the machine, use only genuine Toro • Keep all shields and safety devices in place. If a shield, a replacement parts and accessories. Replacement parts... -
Page 4: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Verticutter Inspect the verticutter. Transport roller assembly Install the transport rollers. Cotter pin O-ring Install the O-ring and the grease fitting. Grease fitting Turf-compensation assembly Long bolt Install the turf-compensation spring... -
Page 5: Inspecting The Verticutter
Note: Determine the left and right sides of the machine from the normal operating position. Note: Whenever the verticutter has to be tipped to expose the verticutter blades, use the kick stand (supplied with Installing the Transport Rollers traction unit) (Figure Parts needed for this procedure: Transport roller assembly... -
Page 6: Installing The O-Ring And The Grease
Installing the O-ring and the Grease Fitting Parts needed for this procedure: O-ring Grease fitting G028407 Procedure g028407 The grease fitting must be installed on the reel motor side of Figure 6 the verticutter. Use the following diagram to determine the position of each reel motor (Figure 1. -
Page 7: Installing The Turf-Compensation Spring
Installing the Adjusting the Blade Depth Turf-Compensation Spring No Parts Required Parts needed for this procedure: Procedure Turf-compensation assembly Note: The maximum recommended blade penetration depth Long bolt is 6 mm (1/4 inch). Carriage bolt 1. Place the verticutter reel on a level surface. Flange locknut 2. -
Page 8: Adjusting The Rear Grass Shield
Adjusting the Rear Grass Adjusting the Roller Scrapers Shield No Parts Required No Parts Required Procedure 1. Loosen the flange nuts that secure the roller scrapers Procedure (Figure 11). Note: When operating in turf conditions where much debris or unusually heavy thatch is encountered, open the rear discharge shield to help allow the debris to discharge from the reel. -
Page 9: Mounting The Verticutter Reel
3. Secure the transport roller bracket to the side plate pin with the cotter pin. 4. Repeat the procedure on the opposite end of the verticutter. Adjusting the Cutting-Unit Steering No Parts Required Mounting the Verticutter Reel Increased Steering for the Rear Cutting Units No Parts Required Increase the steering on the rear cutting units by removing... -
Page 10: Adjusting The Turf-Compensation Settings
G015977 g015977 Figure 14 1. Snapper pin g196971 Note: Fixed steering is recommended when cutting Figure 15 side hills. 1. Hairpin cotter 3. Turf-compensation spring 2. Spring rod 4. Hex nuts 2. Tighten the hex nuts on the front end of the spring rod until the compressed length of the spring is 15.9 cm Adjusting the (6.25 inches) -
Page 11: Product Overview
Product Overview Operation Note: Determine the left and right sides of the machine Specifications from the normal operating position. Net weight 64 kg (140 lb) Training Period Before operating the verticutter reels, evaluate the performance of the reel at the desired setting. Operate in a clear, unused area to determine whether the desired results will be achieved. -
Page 12: Maintenance
Maintenance with a light coating of grease to simplify the assembly (Figure 17). Lubricating the Verticutter Each verticutter has 5 grease fittings (Figure 16) that must be lubricated weekly with No. 2 lithium grease. The lubrication points are the front roller (2), the rear roller (2), and the reel motor splines (1). -
Page 13: Installing The Verticutter Blades
Installing the Verticutter Blades 1. Assemble a reel blade (Figure 18). 2. Assemble a large spacer. 3. Do not invert the reel blades when reassembling them onto the reel shaft. Note: If the blades are inverted, the blades that are in use (rounded) will be mixed with the sharp ends of the blades which were not in use. - Page 14 g007790 Figure 19 6. Bearing nut 1. Rebuild kit (Part No. 114–5430) 2. Rebuild tool kit (Part No. 115–0803) 7. Inner seal tool 3. Inner seal 8. Washer 4. Bearing 9. Bearing/outer seal tool 5. Outer seal...
- Page 15 Notes:...
- Page 16 Notes:...
- Page 17 Notes:...
- Page 18 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 19 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.