hit counter script
JVC GY-HM600U Service Manual
  1. Manuals
  2. Brands
  3. JVC Manuals
  4. Measuring Instruments
  5. GY-HM600U
  6. Service manual

JVC GY-HM600U Service Manual

Hd memory card camera recorder
Hide thumbs Also See for GY-HM600U:
Table of Contents

Advertisement

Quick Links

SERVICE MANUAL
HD MEMORY CARD CAMERA RECORDER
2 S ERVICE MANUAL
2013
HC047<Rev.001>
GY-HM600U, GY-HM600E,
GY-HM650U, GY-HM650E
COPYRIGHT © 2013 JVC KENWOOD Corporation
Note :
Lead free solder used in the board (material : Sn, Ag, In, Bi, melting point : 227 Centigrade)
1
PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1.1
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2
SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
3
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
3.1
Center frame section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
3.2
L Side cover assembly section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
3.3
R Side cover assembly section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
3.4
Handle assembly section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
4
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
4.1
Instruments required for adjustment and the setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12
4.2
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
5
TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21
5.1
Service menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21
5.2
How to update the firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24

TABLE OF CONTENTS

COPYRIGHT © 2013 JVC KENWOOD Corporation
No.HC047<Rev.001>
2013/2

Advertisement

Table of Contents
loading

Related Manuals for JVC GY-HM600U

Summary of Contents for JVC GY-HM600U

  • Page 1: Table Of Contents

    2013 2 S ERVICE MANUAL GY-HM600U, GY-HM600E, GY-HM650U, GY-HM650E COPYRIGHT © 2013 JVC KENWOOD Corporation Note : Lead free solder used in the board (material : Sn, Ag, In, Bi, melting point : 227 Centigrade) TABLE OF CONTENTS PRECAUTION............... . . 1-3 SAFETY PRECAUTIONS .
  • Page 2 SPECIFICATION GY-HM600U, GY-HM600E GY-HM650U, GY-HM650E General Power DC 12 V Power consumption Approx. 10.2 W Approx. 13.0 W (during recording with backlight set to [STANDARD] while the view- (during recording with backlight set to [STANDARD] while the viewfinder is in...

  • Page 3: Precaution

    SECTION 1 PRECAUTION SAFETY PRECAUTIONS Prior to shipment from the factory, JVC products are strictly in- cathode ray tubes and other parts with only the specified spected to conform with the recognized product safety and elec- parts. Under no circumstances attempt to modify these cir- trical codes of the countries in which they are to be cuits.Unauthorized modification can increase the high volt-...
  • Page 4 1.1.2 Safety Check after Servicing Examine the area surrounding the repaired location for damage (4) Leakage current test or deterioration. Observe that screws, parts and wires have been Confirm specified or lower leakage current between earth returned to original positions, Afterwards, perform the following ground/power cord plug prongs and externally exposed ac- tests and confirm the specified values in order to verify compli- cessible parts (RF terminals, antenna terminals, video and...

  • Page 5: Specific Service Instructions

    SECTION 2 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. SECTION 3 DISASSEMBLY Center frame section (3) Pull out the wire from the SDI terminal. (4) Pull out the wire from the connector CN3112 on the NET- 3.1.1 Removing the L side cover assembly (See Figure 1, 2, WORK board, and then remove the L side cover assembly 3 and 4)
  • Page 6 (2) Pull out the wires from the connectors CN203, CN201, CN207, CN214, CN208, CN213, CN209, CN212, CN202, CN204, CN205, CN206, CN215 CN216 on the MAIN board. Handle cover (R) (3) Remove the one screw F attaching the MAIN board, and then remove the MAIN board.

  • Page 7: L Side Cover Assembly Section

    3.1.7 Removing the lens unit (See Figure 16 and 17) • Remove the L side cover assembly and R side cover assembly etc, . (1) Remove the five screws M attaching the board bracket, and then remove the board bracket. Board bracket Rear...

  • Page 8: R Side Cover Assembly Section

    3.2.2 Removing the TC board (See Figure 2) 3.3.2 Removing the R OPE unit (See Figure 2) • Remove teh grip cover assembly. • Remove the GAIN board. (1) Pull out the wires from the connectors CN1212, CN1211, (1) Remove the eight screws B attaching the R OPE unit, and CN1213 CN1214 on the TC board.
  • Page 9 (4) Pull out the FFC wire from the connector CN405 on the 3.4.3 Removing the VF unit (See Figure 7, 8 and 9) HANDLE board, and then remove the handle cover T. • Remove the handle cover T. (1) Remove the four screws F attaching the ACC base, and then remove the ACC base.
  • Page 10 (2) Remove the one screw L attaching the FFC, and then pull out the wire from the connector CN1806. (3) Remove the two screws M attaching the hinge, and then remove the monitor assembly. CN1806 Monitor assembly Fig.11 (2) Pull out the wires from the connectors CN506 CN503 on the XLR board.
  • Page 11 (7) Pull out the wires from the connectors CN301, CN305 CN302 on the AVR board. (8) Remove the six screws S attaching the AVR board, and then remove the AVR board. CN302 CN305 CN301 AVR Board Fig.18 (No.HC047<Rev.001>)1-11...

  • Page 12: Adjustment

    SECTION 4 ADJUSTMENT Instruments required for adjustment and the setup 4.1.1 Measuring instruments required for adjustment Instrument Condition Instrument Condition PC (Windows) With an RS-232C compliant serial Audio tester Calibrated instrument. communication port. Color TV monitor Supporting HD(1080/60i), with an Speaker ---------- HDMI input.
  • Page 13 Adjustment The adjustment for this model is a special adjustment using a PC. Use the adjustment software (HM6xx_Adjust.exe) for adjustment. (1) Preparation of SD card for adjustment This camera can be changed to adjustment mode by using SD card for adjustment. The SD card for adjustment has a file named PROJECT.ADJ in a root directory.

  • Page 14: Adjustment

    (1) Composite tab This is used for Composite signal adjustment. By operating each slide bar, each value can be changed, and by pressing the [READ] button, the current preset value is acquirable. (2) ZOOM MR Tab This is used for Zoom ring adjustment. After pressing the [START] button, adjust by operating the Zoom ring, according to the instruction.
  • Page 15 (4) Ingain tab This is used for Ingain adjustment. The adjustment is automatically performed when pressing the [START] button. (5) AF Filter tab This is used for AF Filter adjustment. The adjustment needs to be performed under the condition of ND 1/16 and ND 1/64. It is automatically performed under each condition when pressing each [START] button.
  • Page 16 4.2.2.2 EEP Tab It is used when reading and writing the data of EEPROM which each microcomputer (CC, BE, IF) has managed. • For example, when reading the data of EEPROM which BE microcomputer has managed, input an address to read into the Adrs colummn on the left side of the [READ] button of BE Write, and press the [READ] button.
  • Page 17 4.2.3 Preparation When the camera is in the adjustment mode, the red “P” letter can be seen at the top of the LCD screen, and this mode is retained until ALL Reset is performed with the adjustment software, even if shutting off the camera. (1) Insert the SD card for adjustment into slot B, and remove it after flashing slot B indicator.
  • Page 18 No. Adjustment Adjustment Signal Adjustment standard Adjustment Adjustment Procedure item type point value range default value Composite Manual ad- Oscillo- Built-in Composite 0.30V 0-255 (1) Set Record Format to 1920 x 1080, analog out- justment scope color bar output (0x71) 50i(HQ) or 1440 x 1080, 50i(HQ), if it has not been set so.
  • Page 19 No. Adjustment Adjustment Signal Adjustment standard Adjustment Adjustment Procedure item type point value range default value (1) Choose ADJ tab -> OIS Drv tab, OIS Drive Automatic adjustment press the [START] button. (2) After pressing the [START] button, adjust so that the shake of a monitor screen comes to minimum, while vi- brating a camera by hand.
  • Page 20 4.2.5 Audio adjustment Perform this adjustment only when you change a microphone. No. Adjustment Adjustment Signal Adjustment standard Adjustment Adjustment Procedure item type point value range default value AUDIO XLR Manual ad- Audio 1kHz ADC DATA -20dBFS ±8 (1) Switch XLR1 input to LINE. Level justment signal...

  • Page 21: Trouble Shooting

    SECTION 5 TROUBLE SHOOTING Service menus 5.1.1 Modes required in servicing While holding down the specified button (FOCUS ONE PUSH 5.1.4 Advanced Function menu operation AUTO), press the [MENU] button to display the first layer menu (1) Refer to 5.1.2 to display the Service menu. of the service menu hierarchy.
  • Page 22 Refer to 5.1.4 Advanced Function Menu because the operations Item Parameter are almost the same. Pixel Compen Cancel Does not execute blemish detec- Item Parameter Det (FA) *1 tion. OutType Consumer The bit in the CONSUMER mode of Execute Executes blemish detection. AES/EBU is added to a SDI output.
  • Page 23 Refer to 5.1.4 Advanced Function Menu because the operations are almost the same. Item Parameter Pixel Com- Does not correct the detected white blemish. Corrects the detected white blemish. Check Light up the pixels which are the de- tected white blemish. Test Signal Off No output test signal.

  • Page 24: How To Update The Firmware

    (1) Refer to 5.1.2 to display the Service menu. card. Check that the directory in SD card is as follows. (2) Select the [Others...], and then press the [Set] button or the \\PRIVATE\JVC\GY-HM600 (In case of GY-HM650, \\PRI- [Cross-Shaped] button (right). VATE\JVC\GY-HM650) (3) The Others menu is displayed.
  • Page 25 (3) The updating is started automatically, after the SD/SDHC 5.2.4 Update error memory card was inserted. When update cannot be performed by a certain cause, it is dis- • A progress bar is displayed on VF during update. played to VF as "Update Error !". •...
  • Page 26 JVC KENWOOD Corporation Professional Systems Business Group, Business Solution Div. (No.HC047<Rev.001>) Printed in Japan...

This manual is also suitable for:

Gy-hm600eGy-hm650uGy-hm650e

Table of Contents