ENGLISH FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it.
Page 4
Children between 3 and 8 years of age and persons • with very extensive and complex disabilities shall be kept away from the appliance unless continuously supervised. Children of less than 3 years of age should be kept •...
ENGLISH The appliance must be connected to the water mains • using the new supplied hose sets, or other new hose sets supplied by the Authorised Service Centre. Old hose sets must not be reused. • If the mains power supply cable is damaged, it must •...
Page 6
2.4 Use to a grounding connection in the building. • Always use a correctly installed WARNING! shockproof socket. Risk of injury, electric shock, • Make sure that the parameters on the fire, burns or damage to the rating plate are compatible with the appliance.
It gaves the highest use in remote control. flexibility. • The ProSense technology detects • The AEG Steam Fragrance, thanks the laundry load size defining the to the steam programmes offers the programme duration in 30 seconds. perfect solution for refreshing even...
3.2 Appliance overview 11 12 Worktop Feet for levelling the appliance Detergent dispenser with AutoDose Drain hose tanks and manual compartments Inlet hose connection Control panel Mains cable Door handle Transit bolts Rating plate Hose support Drain pump filter The rating plate reports: A.
ENGLISH Level of protection against ingress of solid particles and IPX4 moisture ensured by the protective cover, except where the low voltage equipment has no protection against mois‐ ture Water supply pressure Minimum 0.5 bar (0.05 MPa) Maximum 10 bar (1.0 MPa) Cold water Water supply Maximum Load...
Page 10
5. Carefully put the appliance down on It is possible to see its rear side. water flowing from the 6. Put the front polystyrene packaging drain hose. This is due element on the floor under the to the testing with water appliance.
Page 11
If you install the appliance on a plinth adjust the level. that is not an accessory supplied by AEG, secure the appliance with the fixing plates. This spare part is available in web shop or from authorised dealer. Read carefully the instructions supplied with the accessory.
Page 12
You can extend the drain hose to maximum 400 cm. Contact the authorized service centre for the other drain hose and the extension. It is possible to connect the drain hose in different ways: 1. Make a U shape with the drain hose...
Page 13
ENGLISH 6. Position the hose directly to a built- in drain pipe in the room wall and tighten it with a clamp. 5.7 Electrical connection The end of the drain hose must always be ventilated , At the end of installation you can connect i.e.
6. CONTROL PANEL 6.1 Control panel description The options are not selectable with all washing programmes. Check the compatibility between options and washing programmes in the "Options compatibility with programmes" paragraph in the "Programmes" chapter. An option can exclude another one, in this case the appliance doesn't allow you to set the incompatible options together.
Page 15
ENGLISH 6.2 Display Door locked indicator. Washing phase indicator. It flashes during pre-wash and wash phase. Rinsing phase indicator. It flashes during rinse phase. Spinning and draining phase indicator. It flashes during spin and drain phase. Steam phase indicator. Anti-crease phase indicator. Eco programme indicator: it lights on when the selected programme and options have an eco profile.
Page 16
The digital indicator can show: • Programme duration (e. g. The time shown when the programme is set could not correspond to effective duration and change af‐ ter ProSense phase. • Maximum load. • Finish in time (e. g.
ENGLISH The spin area: Spin speed indicator No Spin indicator. Spin phase is off. Extra Silent indicator. Rinse hold indicator. Pre-wash indicator. Stain indicator. Indicators for options downloadable via App only Linked mode indicator. It lights when both AutoDose tanks are linked and filled with the same detergent.
Page 18
7.4 Introduction appears on the display: to reset the Network Credentials. The options/functions are 7.7 Finish In not selectable with all washing programmes. Set this option as last after Check the compatibility programme and other between options/functions options selection, otherwise...
Page 19
ENGLISH When the programme stops the display This option can also be used shows a zero , the indicator to shorten the steam programme duration. steady on and the indicator starts blinking, and the Start / Pause 7.12 Stains/Prewash remains lit. The drum performs smooth movements for about 30 minutes to keep Press this button repeatedly to activate the steam benefit.
7.13 Spin The display shows the indicator The door stays locked. The drum When you set a programme, the turns regularly to reduce creasing. appliance automatically selects the You must drain the water to unlock default spin speed. the door.
ENGLISH • When a laundry overload is detected 2. Press and hold the Extra Rinse and during ProSense phase (a double Plus Steam buttons for some sound played one). seconds. To activate/deactivate this option, hold 3. After 3 seconds the total hours down the Extra Rinse button until a beep operated by the appliance are shown or a double beep sounds.
10. THE AUTODOSE TECHNOLOGY (AUTODOSING) Read this chapter carefully. In some programmes, AutoDose is deactivated (the indicators and/or 10.1 Introduction not displayed and the display shows OFF) Right detergent and fabric softener because there are garments dosage takes better care of the laundry requiring special detergents and ensuring good wash performances.
Page 23
ENGLISH • Maximum level for detergent/ AutoDose additives quantity. 10.3 AutoDose basic setting Manual The factory pre-set doses for a large load are 90 ml for detergent tank and 25 ml for fabric softener tank: the optimal configuration to meet majority of use condition.
Page 24
Water hardness levels Levels Water hardness range mmol/l °f °d °e Soft <15 <8 <10 <1.4 <140 15 - 25 8 - 14 0 - 17 1.5 - 2.5 150 - 250 Medium Hard >25 >14 >17 >2.5 >250...
Page 25
ENGLISH 10.5 Filling the detergent and additives on AutoDose system Please read "Detergents and other treatments" in "Hints and tips" chapter. We recommend that you do not exceed the maximum indicated level ( 4. Gently pour only liquid softener in the 1.
Page 26
10.7 Switching from AutoDose to manual dosing It is possible to disable AutoDose function for one or both tanks by pressing related button symbol. Example: • To switch Fabric Softener tank off, press the Softner button until the display shows OFF.
Page 27
ENGLISH 2. After about 10 seconds the display returns to the programme information screen. 3. If desired, pour the fabric softener in 10.9 Manual filling the detergent and additives the compartment Manual You may need to use a different detergent or fabric softener than the ones used in the AutoDose tanks.
10.10 Drawer open indication When a programme is running, the detergent drawer must always be closed. A sensor in the drawer detects if the drawer is open (or not properly closed) while the programme is running. In such case, the appliance will immediately be paused.
Page 29
ENGLISH Programme Programme description Low energy cycle for cottons. Decreases temperature and ex‐ tends time to reach good washing results. Eco 40-60 White and coloured cotton fabrics. Ideal for normal and heavy soil. Cottons Synthetic items or mixed fabric items. Normal soil. Synthetics Delicate fabrics such as acrylics, viscose and mixed fabrics re‐...
Page 30
Programme Programme description Do not use fabric softener and make sure that Outdoor there is no softener residue in the detergent dispenser. Outdoor clothing, technical, sport fabrics, waterproof and breathable jackets, shell jackets with a removable fleece or in‐...
Page 31
ENGLISH Programme temperature, maximum spin speed and maximum load Programme Default tempera‐ Reference spin Maximum load ture speed Temperature Spin speed range range 30 °C 1400 rpm 5.0 kg 60 °C - 30 °C 1400 rpm - 400 rpm MixLoad 69min 1400 rpm 9.0 kg 40 °C...
Page 32
• Items that are not suitable for tumble drying. The fragrance dose bottles • Items with label "Dry clean only". are available on AEG web shop or by authorised After the steam treatment dealer. the laundry can be humid.
QR code can be used in two ways: Frequency 2.412 - 2.472 GHz • Scan the QR code with the built-in for European mar‐ camera app to download the My AEG Care application from the App store on your smart device and follow the Protocol IEEE 802.11b/g/n required steps.
Page 35
The access point will be open for about 3 Your email and password. If you do minutes. not have an account, create a new 5. Configure the My AEG Care app on one following the instructions in My your smart device and follow the AEG Care.
Page 36
1. Touch the Remote Start button and the indicator blinks on the display for a few seconds. Every time you switch the appliance on, the appliance takes about 10 seconds to connect to the network 2. Touch the Start / Pause button to automatically.
ENGLISH 12.6 Wi-Fi Always On It is possible to turn the appliance on by pressing the On/Off button or through the The Wi-Fi Always On function is App. available in the App. The Wi-Fi Always On This function keeps the appliance function may affect your connected to the network even when the energy consumption.
Page 38
13.4 Setting a programme In the display, the indicator of the operating phase starts flashing. If you wish to change the The programme starts, the door is automatic detergent or fabric locked. The display shows the indicator softener dosage, enter the...
Page 39
ENGLISH 13.8 Programme phase 2. When the drum stops rotating, the display shows the new programme indicators duration, that could increase or decrease, adjusted accordingly the When the programme starts the indicator load detected, the number of bars of the running phase flashes and the indicates the load in quarter (from 1 other phase indicators are steady on.
Page 40
(if they are If the ProSense phase is active). already carried out and the water filling is already In the display all washing phase started, the new programme indicators become steady and the time starts without repeating the area shows .
ENGLISH Press the On/Off button to activate • If you have set , the appliance the appliance again. drains the water and spins. • After 5 minutes from the end of the • If you have set , the appliance washing programme only drains the water.
Page 42
First, follow these generic rules: – powder detergents (also tablets and single-dose detergents) for all types of fabric, excluding delicate. Prefer powder detergents containing bleach for whites and laundry sanitization, – liquid detergents (also single-dose detergents) , preferably for low •...
ENGLISH • Loading the appliance to the laundry in a tumble dryer. This will maximum capacity indicated for save energy during drying! each programmes helps to reduce 14.5 Water hardness energy and water consumption. • With adequate pre-treatment, stains If the water hardness in your area is high and limited soiling can be removed;...
Page 44
15.6 Door seal CAUTION! Do not use alcohol, solvents This appliance is designed with a self or chemical products. cleaning draining system, allowing light fluff fibers that fall off the clothes to be CAUTION! drained out with the water. Regularly Do not clean the metal examine the seal.
Page 45
ENGLISH 3. Deactivate AutoDose function for detergent and softener. 4. Run a short cotton programme at high temperature with empty drum and with a small quantity of powder detergent or, if available, run the Machine Clean programme. If your appliance can be connected to Wi-Fi, the special programme Machine Clean is also downloadable through the APP.
Page 46
4. Press the catch on the back as indicated in the picture and lift up the top cover to remove it. 7. Make sure that all detergent residue is removed from the conveyor. Use only soft damp clothes. 8. Put bottom cover back to its position by aligning its holes on drawer hooks as indicated in the picture.
Page 47
ENGLISH 9. Make sure that all detergent residue is removed from the upper and lower part of the recess. Use a small brush to clean the recess. WARNING! Do not clean with any sharp and metal brushes ora any tools, pumps or sensors allocated on the back of the detergent drawer.
Page 48
Proceed as follows to clean the pump: To restore the functionality, refill tanks with detergent 1. Open the pump cover. and softener. If you place a wrong additives in the tanks, you can easily recover it by using the drain plug on both side of the drawer.
Page 49
ENGLISH 6. Repeat the steps 4 and 5 until the water stops to flow out. 7. Turn the filter anti-clockwise to remove it. 12. Close the pump cover. 8. If it is necessary, remove fluff and objects from the filter recess. 9.
15.11 Emergency drain 2. Remove the inlet hose from the appliance by loosening the ring nut. If the appliance cannot drain the water, carry out the same procedure, described in 'Cleaning the drain pump' paragraph. If necessary, clean the pump.
Page 51
ENGLISH 16.1 Alarm Codes and Possible failures The appliance does not start or it stops during operation. First try to find a solution to the problem (refer to the tables). WARNING! Deactivate the appliance before carrying out any check. With some problems, the display shows an alarm code and the Start / Pause button may flash continuously: If the appliance is overloaded, remove some items...
Page 52
• Make sure that the door is properly closed. The appliance door is open or not closed correctly. • The programme was not finished properly or the appliance stopped too early. Switch the appliance off and on again. Internal fail. No com‐...
Page 53
ENGLISH Problem Possible solution • Make sure that the couplings of the water hoses are tight and there is not water leakages. There is water on the • Make sure that the water inlet hose and the drain hose have floor.
Page 54
Problem Possible solution The display shows • The appliance is downloading any available updates. Wait un‐ til the update process is complete. If you deactivate the appli‐ . All buttons are ance during update, it resumes when you activate the appli‐...
ENGLISH 16.2 Emergency door To open the door, proceed as follows: opening 1. Press the On/Off button to switch the appliance off. In case of power failure or functioning 2. Disconnect the mains plug from the failure the appliance door remains mains socket.
Page 56
The QR code on the energy label supplied with the appliance provides a web link to the information related to the performance of the appliance in the EU EPREL database. Keep the energy label for reference together with the user manual and all other documents provided with this appliance.
ENGLISH Delay start Networked Off (W) Stand-by (W) standby (W) Time to Off/Standby mode is 15 minutes maximum. 1) The energy consumption of the connected function is approximately 17.5 kWh per year. To disconnect this function, please refer to the chapter 'Wi-fi - Connectivity setup'. 17.4 Common programmes These values are indicative only.
Page 58
• Connect the mains plug to the mains When using a liquid socket. detergent in manual • Open the water tap. compartment, insert the • Push the On/Off button to turn the container for liquid appliance on (1). detergent.
Page 59
ENGLISH 18.3 Programmes Programmes Load Product description Cotton and synthetic items. This programme 5.0 kg ensures a good washing performance in a MixLoad 69min short time. Low energy cycle for cottons. Decreases tem‐ 9.0 kg perature and extends time to reach good Eco 40-60 washing results.
19. ENVIRONMENTAL CONCERNS appliances marked with the symbol Recycle materials with the symbol with the household waste. Return the Put the packaging in relevant containers product to your local recycling facility or to recycle it. Help protect the contact your municipal office.
Page 64
My AEG Care app The software in this product contains components that are based on free and open source software. AEG gratefully acknowledges the contributions of the open software and robotics communities to the development project. To access the source code of these free and open source software components whose license conditions require publishing, and to see their full copyright information and applicable license terms, please visit: http://aeg.opensoftwarerepository.com (folder NIUS)