Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to instruction
manual
1. SAFETY
1.1.
ELECTRICAL SAFETY
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
9
all electrical connections for wear and damage. Sealey recommend that an RCD (Residual Current Device) is used with all electrical
products. You may obtain an RCD by contacting your local Sealey dealer. If the Floodlight is used in the course of business duties, it
must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
Electrical safety information, it is important that the following information is read and understood.
Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
9
regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
Ensure that the voltage rating on the appliance suits the power supply to be used.
9
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable.
8
DO NOT use worn or damaged cables, plugs or connectors. Ensure that any faulty item is repaired or
8
replaced immediately by a qualified electrician.
This product should be fitted with a EN 60309 (110volt 16amp) plug.
9
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
9
Replace a damaged plug with a EN 60309 (110volt amp) plug If in doubt contact a qualified
9
electrician.
a) Connect the GREEN/YELLOW earth wire to the earth terminal 'E'.
b) Connect the BROWN live wire to the live terminal 'L'.
c) Connect the BLUE neutral wire to the neutral terminal 'N'.
Ensure that the cable outer sheath extends inside the cable restraint and that the restraint is
9
tight.
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
GENERAL SAFETY
WARNING! Turn off the mains power supply before servicing or performing any maintenance.
‰
Ensure the light is installed correctly in accordance with these instructions.
9
If you use an extension lead the cable must be fully unwound from the drum.
9
▲
DANGER! DO NOT direct the light into a person's eyes. All models have a very intense light
output which, if incorrectly used, could cause eye damage.
DO NOT use the light without the front glass shield.
8
DO NOT use the light near flammable, combustible or explosive liquids, solids, gases or
8
equipment.
Maintain the light in good condition. Repairs must only be undertaken by a qualified electrician (use an authorised service agent).
9
Locate the light in an adequate area for its function, keep area clean and tidy and free from unrelated materials.
9
When not in use, switch off the light and disconnect from the power supply. Ensure that the unit is cool and dry and then store in a
9
safe,dry, childproof area.
DO NOT use the light where it is likely to be knocked or hit.
8
DO NOT install in bathrooms, shower rooms, sauna or such locations.
8
2. INTRODUCTION
360° Slim standing worklight to illuminate the whole area whilst working. SMD LED 60W light producing 6600 lumens. Foldable tripod stand for
easy storage. Includes 110V 16 amp 2P+E plug and 3m cable.
© Jack Sealey Limited
360° SLIM STANDING SMD LED WORKLIGHT
60W 110V
LED60110V
MODEL NO:
Original Language Version
LED60110V
Issue 4 (3)
02/12/22
Advertisement
Related Manuals for Sealey LED60110V
Summary of Contents for Sealey LED60110V
- Page 1 Sealey recommend that an RCD (Residual Current Device) is used with all electrical products. You may obtain an RCD by contacting your local Sealey dealer. If the Floodlight is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable Appliance Test) tested.
- Page 2 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. REGISTER YOUR PURCHASE HERE Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk...