Video cassette recorder nv-hs960 series (64 pages)
Summary of Contents for Panasonic NV-HS825EG
Page 1
ORDER NO. VRD0108035C2 Video Cassette Recorder NV-HS825EG / NV-HS825B / NV-HS825EC / Z-MECHANISM SPECIFICATIONS 2001 Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.
Page 2
/ Please refer to the service manual for Z- Mechanism Chassis. (Order No. VRD9802005C2) 2. The Model No. is indicated on the Schematic Diagram and Circuit Board Diagrams as follows. Model No. Indication Mark NV-HS825EG (EG) NV-HS825B NV-HS825EC (EC) 2. GENERAL DESCRIPTIONS 2.1.
Page 3
STEP2.INPUT THE MODEL & OPTION CODE 1. Set up the applicable model code and option code by ordering the following table. PROCEDURE F.I.P. DISPLAY Turn on the Service Mode 1.Press the FF key and the EJECT key simultaneously for more than 3 seconds. Activate the Service Mode 2 2.While keep placing FF key, press the EJECT key in twice.
Page 4
Model No. Model Option Option Option Code Code 1 Code 2 Code 3 NV-HS825EG (A1h) (08h) (F0h) (00h) NV-HS825B (A3h) (28h) (F0h) (00h) NV-HS825EC (A2h) (08h) (F0h) (00h) Fig. S2 Model Code & Option Code NOTE: 1. Tune the TV Broadcasting channels by referring the memo.
Page 5
When ordering the above procedure, setting of the model code, option code, tuning channel can be skipped. / However, all electrical adjustment data is unique value in accordance with a deck, perform the Electrical Adjustment continuously. 2.1.2. CYLINDER UNIT REPLACEMENT 1.
Page 6
3. UPPER CYLINDER ASSEMBLY When reassembling, perform the steps in the reverse order. Notes: 1. Install the Cylinder Retainer so that the 2 holes on top of the Cylinder Retainer are at right angles with the P3502 Connection. 2. Tighten the Hex screw (C) (1.5 mm) while pressing down on top of the Cylinder Retainer.
Page 7
3. Install the Cylinder Rotor Unit so that the inner hole of the Cylinder Rotor Unit fits to the small projection (D) on top of the Upper Cylinder. 4. Tighten 2 screws (B). Fig. S6 5. install the Cylinder Stator Unit. 6.
Page 8
(PAL: VFJ8125H3F) and adjust it if necessary. 2.1.3. CHECKING OF MAIN C.B.A. When servicing the MAIN C.B.A., take out the MAIN C.B.A. and mechanism from the frame and turn over. Fig. S8 2.1.4. FLAT CARD CABLE INSTALLATION When installing the Flat Card Cable on the connector, install the Flat Card Cable with the cable contacts facing the connector contacts.
Page 9
2.3. INTRODUCTION OF VIDEO HEAD CLEANING CASSETTE / (POLISHING TYPE) 1. We are pleased to introduce Panasonic Video Head Cleaning Cassette, VFK0923FT [for service purposes] and VFK0923FSE [ for end users] for all VHS/SVHS VCP and VCR. 2. These cleaning cassettes are exclusive removing the hard and sticky clogging on video heads.
Page 10
VFK0923FT (For Service usage) Type of Cassette Full VHS Cassette Cleaning Time 10 Seconds/Time Tape Length 20 m Usability in a Path 180 Times VFK0823FSE (For end users) Type of Cassette Full VHS Cassette Cleaning Time 10 Seconds/Time Tape Length 3.34 m Usability in a Path 30 Times...
Page 11
VFK0823FSE (For end users) Note: The tape material itself is the same in both types. 2.4. SELF-DIAGNOSIS RESULT DISPLAY The "SELF-DIAGNOSIS RESULT DISPLAY & MEMORY function is built in this VTR. It means that when the VCR detects undesirable condition, it can be displayed a “Error code (Two numbers from the left)”...
Page 12
INDICATION CAUSE REMEDY/CHECK After cylinder lock is detected, the cylinder Check the cylinder motor drive circuit. does not start rotating again even after tape unloading. Cassette tape is not wound up during the tape Check the capstan motor drive circuit. unloading except EJECT mode.
Page 13
When reassembling, perform the steps in the reverse order. Fig. D1 3.1.2. DETAIL OF DISASSEMBLY METHOD 1. REMOVAL OF THE TOP PANEL Remove 4 Screws (A) Fig.D2 2. REMOVAL OF THE FRONT PANEL UNIT Remove JOG DIAL & SHUTTLE RING Unlock 10 Tabs (B)
Page 14
Fig. D3 3. REMOVAL OF THE MECHANISM UNIT Remove Screw (C) Remove 3 Screws (D) Remove 2 Screws (E) Note: 1. Keep pressing 2 stoppers on Cassette Holder Plate and Press Cassette Holder Plate to the rear. 2. Remove the Mechanism Unit after bend the Cylinder Shield in the direction of the arrow.
Page 15
4. REMOVAL OF THE MAIN C.B.A. Remove Screw (F) Remove 4 Screws (G) Unlock 2 Tabs (H) Fig. D5 NOTE: Before mounting the MAIN C.B.A. onto the frame, be sure to confirm that the insulation sheet is mounted on the frame as shown in Fig.
Page 16
5. REMOVAL OF THE OSD/ SECAM C.B.A. Unlock 4 Tabs (I) Fig. D7 6. SERVICING POSITION Fig. D8 3.2. MECHANICAL ADJUSTMENT PROCEDURES Refer to the Service Manual for Z-Mechanism Chassis. / (Order No. VRD9802005C2)
Page 17
3.3. ELECTRICAL ADJUSTMENT PROCEDURES 3.3.1. TEST EQUIPMENT The following equipments are required for Electrical Adjustments. 1. Dual-Trace Oscilloscope - Voltage Range: 0.005-5V/div - Frequency Range: DC-35MHz - Probes: 10:1 / 1:1 2. Frequency Counter - Frequency Range: 0-10MHz - Probes: 1:1 3.
Page 18
Fig.E1 Fig.E2 Fig.E3 CONDITION: BURST SIGNAL OFF / CONDITION: BURST SIGNAL 75ohm TERMINATED 75ohm TERMINATED Fig.E4 3.3.4. PG SHIFTER ADJUSTMENT / (AUTOMATIC)
Page 19
PROCEDURES FIP DISPLAY Press the FF and EJECT Keys simultaneously for 3 seconds. Press the FF and EJECT Keys simultaneously twice. Press the EJECT key for 3 seconds. Press the CH UP key once. Insert the Alignment cassette tape. (PAL:VFJ8125H3F) When the sequence of the automatical adjustment has been terminated, the following action has been made.
Page 20
PROCEDURES FIP DISPLAY Set the S-VHS SW to ON. / Insert the S-VHS BLANK TAPE. / Input the Video sweep signal (See Fig. E1) to AV3 (S-VIDEO IN) and record it in SP and LP. Press the FF and EJECT Keys simultaneously for 3 seconds.
Page 21
PROCEDURES FIP DISPLAY Set the S-VHS SW to OFF. / Insert the VHS Blank Tape. / Input the Video sweep signal (See Fig. E3) to AV1 (VIDEO IN) and record it in SP and LP. Press the FF and EJECT Keys simultaneously for 3 seconds.
Page 27
11. REPLACEMENT PARTS LIST 11.1. CHASSIS PARTS SECTION PARTS LIST...
Page 28
Ref. No. Part No. Part Name & Description Remarks VEG1574 CYLINDER UNIT [SUPPLIED FROM MBV] VXP2113 UPPER CYLINDER UNIT [SUPPLIED FROM MBV] VDB1256 CYLINDER RETAINER VEM0715 CYLINDER MOTOR UNIT VXS0135 EARTH BRUSH VMD3795 FLAT CABLE HOLDER VEK9069 CAPSTAN UNIT L1AZ00000004 FE HEAD VDB1431 TENSION ARM BOSS...
Page 29
Ref. No. Part No. Part Name & Description Remarks VMD3379 SIDE PLATE (L) VXA6540 SIDE PLATE (R) UNIT VXA5746 CASSETTE HOLDER UNIT VXP1730 MAIN SHAFT UNIT VHD1118 SCREW VHD1118 SCREW VHD0842 SCREW VHD0843 SCREW VHD0843 SCREW VHD0844 SCREW VHD0844 SCREW VHD1066 SCREW VHD1066...
Page 30
Ref. No. Part No. Part Name & Description Remarks VGM1733 TOP PANEL NV-HS825EG-S/EC-S/B-S VGM1748 TOP PANEL [SUPPLIED FROM MBV]NV-HS825EG-K VYP8154 FRONT PANEL UNIT [SUPPLIED FROM MBV]NV-HS825EG-S VYP8156 FRONT PANEL UNIT [SUPPLIED FROM MBV]NV-HS825EG-K VYP8159 FRONT PANEL UNIT [SUPPLIED FROM MBV]NV-HS825B-S...
Page 31
[SUPPLIED FROM MBV] VPN5555 CUSHION (L) [SUPPLIED FROM MBV] VPN5554 CUSHION (R) [SUPPLIED FROM MBV] VPG0J94 PACKING [SUPPLIED FROM MBV]NV-HS825EG-S/ EC-S/B-S VPG0K19 PACKING [SUPPLIED FROM MBV]NV-HS825EG-K SERVICE FIXTURES & TOOLS VFJ8125H3F VHS ALIGNMENT TAPE (PAL) VFK0335 RETAINING RING REMOVER (3mm/...
Page 32
Ref. No. Part No. Part Name & Description Remarks VEP06E08J MAIN C.B.A. [SUPPLIED FROM MBV](RTL)NV- HS825EG-S/EG-K THE FOLLOWING C.B.A.S ARE INCLUDED IN MAIN C.B.A. VEP07A16A,VEP07A23L VEP07A16A DECODER PACK C.B.A. [SUPPLIED FROM MBV](RTL)NV- HS825EG-S/EG-K INCLUDED IN MAIN C.B.A.(VEP06E08J). VEP07A23L TV DEMODULATOR PACK C.B.A [SUPPLIED FROM MBV](RTL)NV- HS825EG-S/EG-K INCLUDED IN MAIN C.B.A.(VEP06E08J).
Page 62
L0201 R0208 UNLOADING C0208 HOLE LOADING SENSOR R0204 C0210 C0209 ED/S TORQUE DIRECTION OUT2 CAPSTAN MOTOR DRIVER MAIN COIL HALL POWER R0209 OUT1 EC AMP HOLE SENSOR TL0205 DRIVER CONTROL LOGIC R0201 R0211 C0206 C0207 NV-HS825EG/B/EC CAPSTAN UNIT SCHEMATIC DIAGRAM...
Page 63
MAIN COIL 2 MAIN COIL 3 HALL IC GND (CYL) MAIN COIL 1 NV-HS825EG/B/EC CYLINDER STATOR UNIT NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. SCHEMATIC DIAGRAM...
Page 64
0.012 0.012 NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NV-HS825EG NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. ORDERING. WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. DECODER PACK SCHEMATIC DIAGRAM...
Page 65
NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE IN THE BRACKEST( )ON THIS DIAGRAM IS RECORD MODE WITH PAL COLOUR SIGNAL.(SP MODE) NV-HS825EG/B/EC NOTE:DO NOT ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 66
GND (LVM) N.SW 5V GND (HA2) PS 12V NV-HS825EG/B/EC Hi-Fi AUDIO SECTION IN MAIN NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE IN THE BRACKETS( )ON THIS DIAGRAM IS RECORD MODE THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU...
Page 67
AV3 A IN (L) AV3 C IN GND (AV) AV3 Y IN AV3 S-VHS IN R4804 R4805 NV-HS825EG/B/EC NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. FRONT SCHEMATIC DIAGRAM...
Page 68
TP3022 R3910 4700 (RGB OFF :ON) NV-HS825EG/B/EC INPUT/OUTPUT PACK NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE IN THE BRACKETS( ) ON THIS DIAGRAM IS RECORD MODE THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE...
Page 69
SHUTTLE 1 SHUTTLE 2 SHUTTLE 3 JOG/SHUTTLE SHUTTLE 4 S6309 VSQ0817 JOG A JOG B NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NV-HS825EG/B/EC ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. JOG SCHEMATIC DIAGRAM...
Page 71
C7714 C7730 6V220 6V220 NV-HS825EG/B/EC NOTE:DO NOT USE PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR OSD/SECAM SCHEMATIC DIAGRAM NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. ORDERING.WHEN YOU ORDER A PART,PLESE REFER TO PARTS LIST.
Page 72
R1111 C1111 R1203 R1205 0.01 2200 NOTE1:WHEN MEASURE THE VOLTAGE OR WAVEFORM ON THE POWER TRANSFORMER NV-HS825EG/B/EC CIRCUIT,SET THE GND TERMINAL OF MEASURING POINT AS FOLLOWS. POWER TRANSFORMER PRIMARY SIDE..SECONDARY SIDE... SECTION IN MAIN IMPORTANT SAFETY NOTICE: NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY.
Page 73
150K D1001 D1006 R7652 MA165 MA165 100K NV-HS825EG/B/EC POWER SUPPLY/RF IMPORTANT SAFETY NOTICE: NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SECTION IN MAIN COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS FOR SAFETY. SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE.
Page 74
POWER KEY 0.56u 2SD601A 470P 0.01 560P POWER OFF (AMP) R6003 C6007 C6006 RESET 150P 120P C6008 SHORT DET TW2001 1000P OSD VIDEO OUT AV PB 12V BACK UP 5V NV-HS825EG/B/EC SYSTEM CONTROL & SERVO SECTION IN MAIN SCHEMATIC DIAGRAM...
Page 75
100u POWER SAVE PROJECT 50 C6001 UNREG 14.5V 6V47 NV-HS825EG/B/EC SYSTEM CONTROL & SERVO SECTION IN MAIN NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR SCHEMATIC DIAGRAM NV-HS825EG/B/EC SYSTEM CONTROL & SERVO SECTION IN MAIN SCHEMATIC DIAGRAM...
Page 76
6V220 4300 5600 8200 BACK UP 5V NV-HS825EG/B/EC EJECT SW TIMER SECTION IN MAIN NOTE:DO NOT USE PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. ORDERING.WHEN YOU ORDER A PART,PLESE REFER TO PARTS LIST.
Page 77
4MHz C0711 R0715 16V22 NV-HS825EG/B/EC NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR TV DEMODURATOR PACK SCHEMATIC DIAGRAM NOTE:THE MEASUREMENT MODE OF THE DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 78
NOTE:THE MEASUREMENT MODE OF THE DC VLOLTAGE IN THE BRACKETS( )ON THIS DIAGRAM IS RECORD MODE THE MEASUREMENT MODE OF THE DC VOLTAGE OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE NV-HS825EG/B/EC LUMINANCE & CHROMINANCE/AUDIO SECTION IN MAIN SCHEMATIC DIAGRAM WITH PAL COLOUR SIGNAL.(SP MODE)
Page 79
FREQ.ADJ L3003 AV3 C IN VIDEO/Y IN NORMAL L3015 NV-HS825EG/B/EC LUMINANCE & CHROMINANCE/AUDIO NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NV-HS825EG/B/EC LUMINANCE & CHROMINANCE/AUDIO SECTION IN MAIN SCHEMATIC DIAGRAM SECTION IN MAIN SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 80
CYLINDER STATOR UNIT Integrated Circuit HALL IC Connector M1 VM P2901 ADDRESS INFORMATION HALL IC VM M2 P2901 NV-HS825EG/B/EC (VEM0715) CYLINDER STATOR UNIT...
Page 93
NAME P-OFF P-SAVE P-FAIL Reset Description 1 CURRENT_LIMIT O Current limit terminal for Capstan driver. 2 F ADJUST O Analogue voltage output for Head frequency response adjustment. 3 SCAS_IN(L) I Detection Terminal for VHS tape or S-VHS tape. Switching terminal of NTSC-PB trap filter for FM audio. (1).When the Playback detection result is 60Hz in the "VV"mode 4 PB60Hz(H) (PB,TRICK/PB,ADUB,ADUB-PS), the high (H) signal is outputted.
Page 94
NAME P-OFF P-SAVE P-FAIL Reset Description 37 V EE(L) O Output terminal of EE and VV switching. 38 D REC(H) O Timing control terminal for video recording current. 39 D.A.REC(H) O Timing control terminal for linear audio recording current. 40 BIAS(L) O Bias oscillation control terminal for linear audio.
Page 95
NAME P-OFF P-SAVE P-FAIL Reset Description Input terminal of condition of the erasure prevention tab on the cassette tape. 92 S TAB(L) *With tab : "Low" / Without tab : "High". 93 T.REEL.PULSE I Input terminal for the pulse from Take-up Reel Sensor. 94 S.REEL.PULSE I Input terminal for the pulse from Supply Reel Sensor.
Page 96
INPUT CONDITION VIDEO OUTPUT RESULT AUDIO OUTPUT RESULT POWER INPUT RF (C) AV1 Out AV2 Out SELECT ON(H) PB(H) PB(H) PB(H) Selector Selector AV2 In AV1 In AV2 In AV1 In Mute AV2 In AV1 In AV2 In AV1 In AV2 In AV1 In Mute...
Page 97
INPUT CONDITION VIDEO OUTPUT RESULT AUDIO OUTPUT RESULT POWER INPUT RF (C) AV1 Out AV2 Out SELECT ON(H) PB(H) PB(H) PB(H) Selector Selector P.ON NO.TU VCR out VCR out INSEL C+.TU VCR out VCR out INSEL VCR out VCR out AV1 In AV1 In AV1 In...
Page 98
INPUT CONDITION VIDEO OUTPUT RESULT AUDIO OUTPUT RESULT POWER INPUT RF (C) AV1 Out AV2 Out SELECT ON(H) PB(H) PB(H) PB(H) Selector Selector P.ON DECODER VTR NO.TU VCR out AV1 In AV1 In AV1 In VCR out AV1 In AV1 In AV1 In C+.TU VCR out TUN IN...
Page 99
INPUT CONDITION VIDEO OUTPUT RESULT AUDIO OUTPUT RESULT POWER INPUT RF (C) AV1 Out AV2 Out SELECT ON(H) PB(H) PB(H) PB(H) Selector Selector AV2 In AV1 In AV2 In AV1 In Mute AV2 In AV1 In AV2 In AV1 In AV2 In AV1 In Mute...
Page 100
INPUT CONDITION VIDEO OUTPUT RESULT AUDIO OUTPUT RESULT POWER INPUT RF (C) AV1 Out AV2 Out SELECT ON(H) PB(H) PB(H) PB(H) Selector Selector P.ON VCR out VCR out INSEL VCR out VCR out AV1 In AV1 In AV1 In AV1 In INSEL VCR out VCR out AV2 In...
Page 101
SYSTEM CONTROL & SERVO ICs DC VOLTAGE CHART (SP MODE) IC1501 IC1502 Ref. No. MODE STOP PLAY IC2501 Ref. No. MODE STOP 15.5 PLAY 15.5 15.5 15.5 15.5 IC6001 Ref. No. MODE STOP PLAY IC6001 Ref. No. MODE STOP PLAY IC6001 Ref.
Page 102
SYSTEM CONTROL & SERVO TRs DC VOLTAGE CHART (SP MODE) Q1501 Q1502 Q6002 Q6005 Ref. No. MODE STOP PLAY Q6007 Q6008 Q6009 Q6010 Ref. No. MODE STOP -0.1 11.8 PLAY 11.2 11.8 11.8 -0.1 11.8 11.8 11.8 QR6001 QR6002 QR6004 QR6005 Ref.
Page 103
4.43 NTSC L BILINGUAL 443NT [L] BILINGUAL L A. COMP BIL [L] AUDIO COMPONENT SIGNAL BILINGUAL H BIL. [H] A. COMPO AUDIO COMPONENT SIGNAL BILINGUAL L AUDIO DUBBING PAUSE L BIL/M1 [L] A. D.P [L] AUDIO DUBBING PAUSE L BS CLOCK A.
Page 104
CYL GND CYLINDER GND FULL. E. 12V FULL ERASE 12V DELAIED FM RECORDING H D.F.M. REC [H] GND (ANALOG) GND [A] DELAIED FM RECORDING L D. FM REC [L] GND (TUNER) GND [TU] D. GND GND/NON SW 12V DIGITAL GND GND/N.
Page 105
POWER OFF H LINE IN [R] LINE INPUT (R) P-OFF [H] POWER OFF L LINE OUT [L] LINE OUTPUT (L) P-OFF [L] LINE OUT [R] LINE OUTPUT (R) P. FAIL POWER FAILURE DETECT LP H POWER OFF H LP [H] P.
Page 106
SYSTEM CONTROL 5V RF OUT RF OUTPUT SYSCON 5V SYSTEM SW RF Y RF LUMINANCE SIGNAL SYSTEM TAKE-UP PHOTO TRANSISTOR RF. Y. IN RF LUMINANCE SIGNAL INPUT T-PHOTO TAKE-UP REEL PULSE RF. Y. OUT RF LUMINANCE SIGNAL OUTPUT T-RL. PLS TIMER BUS CLOCK ROTAR.
Page 107
If you lose the fuse cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your local Panasonic Dealer. IF THE FITTED MOULDED PLUG IS UNSUITABLE TYPE B FOR THE SOCKET OUTLET IN YOUR HOME THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.
Page 108
8 SCHEMATIC DIAGRAMS 8.1. POWER TRANSFORMER SECTION IN MAIN SCHEMATIC DIAGRAM THE STRIPED FRAME INDICATES THE PRIMARY CIRCUIT TO DISTINGUISH THE PRIMARY CAUTION FROM THE SECONDARY CIRCUIT. PAY ATTENTION NOT TO RECEIVE AN ELECTRIC SHOCK DURING REPAIR AND SERVICE OF THE PRODUCTS.
Page 109
2200 C1111 R1203 R1205 0.01 2200 POWER TRANSFORMER NV-HS825EG/B/EC FOLLOWS. POWER TRANSFORMER NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR SECTION IN MAIN N THE VOLTAGE WHEN ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 110
8.2. POWER SUPPLY/ RF SECTION IN MAIN SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE :TO POWER TRANSFORMER SECTION :TO SYSTEM CONTROL & SERVO SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION Q1001 QR1002 Q1011 :TO Hi-Fi AUDIO SECTION 2SD602A...
Page 111
(BUFFER) R7653 R7654 150K 150K R7652 100K NV-HS825EG/B/EC POWER SUPPLY/RF NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SECTION IN MAIN SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU DC VOLTAGE ON THIS DIAGRAM IS STOP MODE. SCHEMATIC DIAGRAM ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 112
8.3. TIMER SECTION IN MAIN SCHEMATIC DIAGRAM DP7501 A2BD00000040 :TO POWER TRANSFORMER SECTION :TO POWER SUPPLY/RF SECTION S-VHS :TO SYSTEM CONTROL & SERVO SECTION :TO Hi-Fi AUDIO SECTION Link R7508 HEATER (+) C7501 0.01 HEATER DC (-) D7501 C7502 R7511 R7510 MN4220NM 50V10...
Page 113
S7510 S7516 EVQ11L07B EVQ11L07B EVQ11G07K EVQ11G07K R7519 R7536 R7522 R7523 4300 5600 8200 NV-HS825EG/B/EC TIMER SECTION IN MAIN NOTE:DO NOT USE PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLESE REFER TO PARTS LIST. SCHEMATIC DIAGRAM...
Page 114
8.4. SYSTEM CONTROL & SERVO SECTION IN MAIN SCHEMATIC DIAGRAM :TO POWER TRANSFORMER SECTION CAPSTAN SERVO SPEED LOOP CAPSTAN SERVO PHASE LOOP CYLINDER SERVO SPEE :TO POWER SUPPLY/RF SECTION :TO LUMINANCE & CHROMINANCE/AUDIO SECTION :TO Hi-Fi AUDIO SECTION :TO TIMER SECTION R2507 R2508 C2514...
Page 116
SAVE C6034 220P Q6007 2SD1819A (BUFFER) R6068 R6069 R2520 R2521 R2522 220K 100K QR6004 R1017 R6016 XN1211 (SLEEP :OFF) R2509 C2524 L2501 C2516 C2526 R2518 6V220 L6001 100u C6001 6V47 NV-HS825EG/B/EC SYSTEM CONTROL & SERVO SECTION IN MAIN SCHEMATIC DIAGRAM...
Page 117
R2517 R2519 SLEEP POWER SAVE PROJECT 50 UNREG 14.5V NV-HS825EG/B/EC SYSTEM CONTROL & SERVO SECTION IN MAIN NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 118
8.5. LUMINANCE & CHROMINANCE/ AUDIO SECTION IN MAIN SCHEMATIC DIAGRA VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE :TO POWER SUPPLY/RF SECTION :TO SYSTEM CONTROL & SERVO SECTION :TO Hi-Fi AUDIO SECTION N SW 5V PAL EP C4017 QR4005...
Page 120
-10dB R4072 100K R4065 FROM -10dB -10dB CLAMP 3300 QR4002 MESEC -DET UN2211 IC3001 (PAL EP :ON) C4016 C1AB00001299 6V100 (1.8) (0.1) (2.6) TW3001 C3002 150P R3003 1500 NOTE:DO NO NV-HS825EG/B/EC LUMINANCE & CHROMINANCE/AUDIO SECTION IN MAIN SCHEMATIC DIAGRAM ORDER...
Page 121
(SWITCHING) FREQ.ADJ L3003 AV3 C IN VIDEO/Y IN NORMAL L3015 NV-HS825EG/B/EC LUMINANCE & CHROMINANCE/AUDIO NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR SECTION IN MAIN SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 122
8.6. Hi-Fi AUDIO SECTION IN MAIN SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE AUDIO MAIN SIGNAL PATH IN REC MODE :TO POWER SUPPLY/RF SECTION :TO SYSTEM CONTROL & SERVO SECTION VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNAL PATH IN PLAYBACK MOD :TO LUMINANCE &...
Page 123
TUNER AUDIO (L) L4501 1.2u GND (SYS) GND (LVM) GND (HA2) NV-HS825EG/B/EC NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS Hi-Fi AUDIO SECTION IN MAIN RACKETS ON THIS DIAGRAM IS PLAYBACK MODE SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU SCHEMATIC DIAGRAM...
Page 124
8.7. INPUT/ OUTPUT PACK SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MODE AUDIO MAIN SIGNA R3911 R390 L3907 C3945 R3939 C3936 C3937 R3908 R3938 6V330 220K Q3902 2SD601A R3912 C3914 C3913 R3906 C3912 L3908 (AMP)
Page 125
UN2212 P3022 R3910 4700 (RGB OFF :ON) NV-HS825EG/B/EC INPUT/OUTPUT PACK OUT OF THE BRACKETS ON THIS DIAGRAM IS PLAYBACK MODE NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST.
Page 126
8.8. DNR PACK SCHEMATIC DIAGRAM VIDEO MAIN SIGNAL PATH IN REC MODE VIDEO MAIN SIGNAL PATH IN PLAYBACK MOD A-LINE LB3302 V BLK VR3001 C3302 C3303 R3326 C3301 100KB 0.01 680P 5600 0.01 R3302 PS3301 R3323 110K Y/C C OUT C3304 CNR OFF R3301...
Page 127
0.01 Q3303 C3430 2SB1218A 0.01 (AMP) C3427 C3415 C3428 C3429 C3431 C3432 16V10 16V10 L3317 NV-HS825EG/B/EC NOTE:DO NOT ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. DNR PACK SCHEMATIC DIAGRAM...
Page 129
C7715 C7729 R7745 6V100 L7701 R7746 100u L7703 R7747 100u R7748 C7731 C7714 C7730 6V220 6V220 NV-HS825EG/B/EC NOTE:DO NOT USE PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR OSD/SECAM SCHEMATIC DIAGRAM ORDERING.WHEN YOU ORDER A PART,PLESE REFER TO PARTS LIST.
Page 130
8.10. TV DEMODULATOR PACK SCHEMATIC DIAGRAM VIDEO SIGNAL PATH AUDIO SIGNAL PATH R0713 C0724 220P: EG/EC 330P:B R0742 Q0702 2SD601A (AMP) PK0701 DU7601-19 DU7601-20 C0721 R0741 DU7601-21 120P: DU7601-22 SIF/QPSK EG/EC DU7601-23 AFC S-CURVE 82P:B DU7601-24 TUNER VIDEO DU7601-25 TUNER 5V R0743 DU7601-26 IC0701...
Page 131
R0707 C0702 C0703 1000P R0719 C0712 4700 X0704 VLF1493: EG/EC VLF1495: C0710 0.01 L0703 R0725 2.2u:EG/EC 1.8u:B C0715 EG/EC 12P:B C0711 R0715 16V22 NV-HS825EG/B/EC SHOWN ON THIS SCHEMATIC DIAGRAM FOR TV DEMODURATOR PACK SCHEMATIC DIAGRAM PART,PLEASE REFER TO PARTS LIST.
Page 133
10KB TL7303 R7306 R7305 5600 5600 X7301 C7307 C7304 VSX1086 680P 680P C7306 C7305 0.012 0.012 E ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR NV-HS825EG WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. DECODER PACK SCHEMATIC DIAGRAM...
Page 136
MAIN COIL 2 MAIN COIL 3 HALL IC GND (CYL) MAIN COIL 1 NV-HS825EG/B/EC CYLINDER STATOR UNIT NOTE:DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. SCHEMATIC DIAGRAM 8.14.
Page 137
R0212 R0213 Q0203 Q0202 Q0201 R0210 D0203 TL0204 TL0202 TL0203 TL0201 L0201 C0208 R0204 C0210 C0209 OUT2 CAPSTAN MOTOR DRIVER MAIN COIL OUT1 TL0205 DRIVER CONTROL LOGIC NV-HS825EG/B/EC CAPSTAN UNIT SCHEMATIC DIAGRAM...
Page 138
GND (AV) AV3 Y IN AV3 S-VHS IN R4804 R4805 NV-HS825EG/B/EC NOTE: DO NOT USE ANY PART NUMBER SHOWN ON THIS SCHEMATIC DIAGRAM FOR ORDERING.WHEN YOU ORDER A PART,PLEASE REFER TO PARTS LIST. FRONT SCHEMATIC DIAGRAM 8.16. JOG SCHEMATIC DIAGRAM...
Page 140
IC3001 AUDIO HEAD P5001 MUTE Q7601 FROM DECODER/ TUNER AUDIO (N) MUTE TV DEMODU FM MODULATOR/ DEMODULATOR NORMAL A.HEAD (W) MUTE SELECT SWITCH TO/FROM FROM MUTE AC HEAD & MUTE SYSTEM SWITCH CONTROL MUTE A.HEAD (R) NV-HS825EG/B/EC AUDIO BLOCK DIAGRAM...
Page 141
CH UP N.SW S7512 S7503 S7504 Q1501 D1501 Q1502 S7507 TAKE UP SENSOR SUPPLY SAFETY T-REEL PULSE PHOTO PHOTO TAB SW SENSOR SENSOR P4002 CTL HEAD (-) HEAD P4002 NV-HS825EG/B/EC 112 CTL HEAD (+) SYSTEM CONTROL & SERVO BLOCK DIAGRAM...
Page 142
TUNER VIDEO TP3023 PP3904 PS3904 PS3905 PP3905 AV3 C IN JK4801 VIDEO IN PS4801 PP3906 FRONT VIDEO IN IC3991 JK4802 S-VIDEO PS4801 PP3906 FRONT C IN PS4801 PP3906 FRONT Y IN NV-HS825EG/B/EC LUMINANCE & CHROMINANCE BLOCK DIAGRAM AV3 S IN...
Page 143
HEAD TO/FROM TRAP CYLINDER LEVEL & SW VIDEO HEAD SECAM L.P.F. P5001 LP/EP L P5001 MAIN C BDL LP/EP COM CONV 2 P5001 LP/EP R LP/EP Q3005 NV-HS825EG/B/EC Q3006 NV-HS825EG/B/EC LUMINANCE & CHROMINANCE BLOCK DIAGRAM LUMINANCE & CHROMINANCE BLOCK DIAGRAM...