Table of Contents
Advertisement
Quick Links
C H A P T E R
2
Preparing for Installation
This chapter provides safety information and describes the tasks you must perform before
you install the LightStream 100 ATM switch.
This chapter contains the following sections:
•
Safety Recommendations
•
Installation Environmental Conditions
•
Confirming the Contents of the Shipping Container
•
LightStream 100 ATM Switch Components
Safety Recommendations
The following guidelines will help to ensure your general safety and protect the equipment:
•
Keep the chassis area clear and dust-free during and after installation.
•
Put the removed chassis cover in a safe place.
•
Keep tools away from walk areas where you and others could fall over them.
•
Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf
and roll up your sleeves.
•
Wear safety glasses if you are working under any conditions that might be hazardous to
your eyes.
•
Do not perform any action that creates a potential hazard to people or makes the
equipment unsafe.
Preparing for Installation 2-1
Advertisement
Table of Contents
Related Manuals for Cisco LightStream 100
Summary of Contents for Cisco LightStream 100
-
Page 1: Preparing For Installation
C H A P T E R Preparing for Installation This chapter provides safety information and describes the tasks you must perform before you install the LightStream 100 ATM switch. This chapter contains the following sections: • Safety Recommendations •... -
Page 2: Maintaining Safety With Electricity
“TN Power Warning” section in the “Translated Safety Warnings” appendix. • Locate the emergency power-off switch for the room in which you are working. Then, if an electrical accident occurs, you can act quickly to turn OFF the power. •... -
Page 3: Preventing Electrostatic Discharge Damage
• Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, and missing safety grounds. • If an electrical accident occurs, proceed as follows: — Use caution; do not become a victim yourself. —... -
Page 4: Installation Environmental Conditions
Installation Environmental Conditions Installation Environmental Conditions Install the LightStream 100 ATM switch in an area that meets the following conditions: Make sure the LightStream 100 switch remains operational within the temperature and humidity limits shown in Table 1-3. Allow the following minimum vacant space surrounding the LightStream 100 switch to ensure proper heat radiation: —... - Page 5 The quantity and type of cards depend on your system configuration. LightStream 100 ATM Switch Components References throughout this publication refer to the LightStream 100 ATM switch front and rear panel layouts. Figure 2-1 shows the front panel layout, and Figure 2-2 shows the rear panel layout.
- Page 6 LightStream 100 ATM Switch Components Figure 2-1 Run LED Status LED Failure LED 2-6 Cisco LightStream 100 User Guide LightStream 100 ATM Switch Front Panel EIA/TIA-232 Ethernet connection Reset button Operator LEDs (16) LEDs...
- Page 7 LightStream 100 ATM Switch Components Figure 2-2 LightStream 100 ATM Switch Rear Panel Cooling fans AC power connector Power switch Preparing for Installation 2-7...
- Page 8 LightStream 100 ATM Switch Components Figure 2-3 LightStream 100 ATM Switch Internal View GWPAD : Gateway Packet Assembler/Disassembler LINF BCONV : Bus Converter PROC 2-8 Cisco LightStream 100 User Guide Motherboard Power supply Line Interface Processor Versa Module Eurocard LINF card...
- Page 9 Subboard ATOM switch LINF card ATOM SW Asynchronous Transfer Mode Output-Buffer Modular Switch CLKGEN Clock Generator DMUX Demultiplexer GWPAD Gateway Packet Assembler/Disassembler LINF Line Interface Multiplexer LightStream 100 ATM Switch Components CLKGEN MUX/DMUX GWPAD card Motherboard Preparing for Installation 2-9...
- Page 10 LightStream 100 ATM Switch Components 2-10 Cisco LightStream 100 User Guide...