Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
instruction
manual
1. SAFETY
‰
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this bench.
9
Locate the bench in a suitable work area.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
‰
WARNING! Use the bench on level and solid ground, preferably concrete.
9
Keep the bench clean and tidy in accordance with good workshop practice.
9
Keep children and unauthorised persons away from the work area.
8
DO NOT use the bench for any purpose other than for which it is designed.
8
DO NOT undertake work on the bench without the workpiece being adequately secured.
8
DO NOT use the bench outdoors.
8
DO NOT clean the bench with any solvents which may damage the surface or the protective coating on the worktop.
8
DO NOT get the bench wet or use in damp or wet locations or areas where there is condensation.
2. INTRODUCTION
Made from Rubber Wood. Features tool well, shelf, 4 tool drawers, front vice, four metal bench stops and four wooden board jacks.
Supplied with 4 Wooden Pegs and 4 Anvil Pegs.
3. SPECIFICATION
Model No: ................................................................. AP1640
Overall Size (W x D x H): .......... 1520mm x 620mm x 820mm
Worktop: .........................................................1520 x 500mm
4. CONTENTS
Part
Description
no.
1
Table top
2
Shelf
3
Cross brace
4
Leg
5
Vice
6
Screw 60mm
7
Bolt 90mm
8
Connecting nut
9
Hex wrench 50mm
10
Wood peg
11
Anvil peg
12
Vice screw & washer
13
Screw 30mm
14
Screw 35mm
15
Sliding partition
16
Lower support
17
Drawer front panel (P1)
18
Drawer back panel (P2)
19
Drawer panel (P3)
© Jack Sealey Limited
1.52M WOODWORKING BENCH WITH 4
DRAWERS
AP1640
MODEL NO:
Quantity
1
1
2
2
1
4
4
8
1
4
4
1
32
8
1
2
4
4
4
Original Language Version
Tool Well: ........................................................ 1110 x 410mm
Drawer(x4): ...............................................460 x 390 x 80mm
Vice (x1): ...............................280mm wide x 180mm opening
AP1640 Issue:1 17/05/22
Advertisement
Related Manuals for Sealey AP1640
Summary of Contents for Sealey AP1640
- Page 1 AP1640 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 4 pcs of 35mm screws (14) at both ends of the feet. Step 6: The lower support(16) is also attached to the partition wall with rails (15) using 2 pcs of 35mm screws (14). Original Language Version © Jack Sealey Limited AP1640 Issue:1 17/05/22...
- Page 3 Step14: Fasten the holding rods (10) and the bench hooks (11) in the holes provided in the worktop. Original Language Version © Jack Sealey Limited AP1640 Issue:1 17/05/22...
- Page 4 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...