hit counter script
Honeywell Granit 1280i User Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Scanner
  5. Granit 1280i
  6. User manual

Honeywell Granit 1280i User Manual

Industrial full range laser scanner
Hide thumbs Also See for Granit 1280i:
Table of Contents

Advertisement

Quick Links

Download this manual
Granit™ 1280i
Industrial Full Range Laser Scanner
User's Guide
http://manualforhoneywellthermostat.com

Advertisement

Table of Contents
loading

Related Manuals for Honeywell Granit 1280i

Summary of Contents for Honeywell Granit 1280i

  • Page 1 Granit™ 1280i Industrial Full Range Laser Scanner User’s Guide http://manualforhoneywellthermostat.com...
  • Page 2 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.
  • Page 3 Use only shielded data cables with this system. This unit has been tested with cables less than 3 meters. Cables greater than 3 meters may not meet class B performance. Caution: Any changes or modifications made to this equipment not expressly approved by Honeywell may void the FCC authorization to operate this equipment.
  • Page 4 5627 BT Eindhoven The Netherlands Honeywell International Inc. shall not be liable for use of our product with equipment (i.e., power supplies, personal comput- ers, etc.) that is not CE marked and does not comply with the Low Voltage Directive.
  • Page 5 For patent information, please refer to www.hsmpats.com. Solids and Water Protection The Granit 1280i has a rating of IP65, totally protected against dust and protected against low pressure water jets. Warning To reduce the possibility of heat-related injuries, avoid touching sections of the scanner that feel warm.
  • Page 6 Required Safety Labels Granit 1280i Scanner Laser Output Laser Label location Part Number, Serial Compliance Number and Revision label location Information location...

  • Page 7: Table Of Contents

    ® Verifone Ruby Terminal Default Settings................2-2 ® Gilbarco Terminal Default Settings ..................2-2 Honeywell Bioptic Aux Port Configuration ................2-2 ® Datalogic™ Magellan Aux Port Configuration..............2-2 NCR Bioptic Aux Port Configuration ..................2-3 Wincor Nixdorf Terminal Default Settings ................2-3 Wincor Nixdorf Beetle™ Terminal Default Settings .............2-3 RS232 Modifiers ........................2-4...
  • Page 8 Beep on BEL Character....................... 3-2 Good Read and Error Indicators..................3-2 Beeper – Good Read..................... 3-2 Beeper Volume – Good Read..................3-2 Beeper Pitch – Good Read.................... 3-3 Beeper - Transmit Order....................3-3 Vibrate – Good Read ..................... 3-3 Beeper Pitch – Error ...................... 3-4 Beeper Duration –...
  • Page 9 Output Sequence Overview....................3-16 Output Sequence Editor ....................3-16 To Add an Output Sequence ..................3-16 Other Programming Selections..................3-17 Output Sequence Editor ....................3-18 Sequence Timeout....................... 3-18 Sequence Match Beeper ..................... 3-18 Partial Sequence ......................3-19 Require Output Sequence ................... 3-19 No Read ..........................
  • Page 10 Code 39 ..........................6-5 Code 32 Pharmaceutical (PARAF) ................6-6 Full ASCII........................6-7 Code 39 Code Page ...................... 6-7 Interleaved 2 of 5......................... 6-8 Matrix 2 of 5......................... 6-9 NEC 2 of 5 ......................... 6-11 Code 93 ..........................6-12 Code 93 Code Page ....................6-13 Straight 2 of 5 Industrial (three-bar start/stop)..............
  • Page 11 Read Time-Out ......................8-3 Resetting the Custom Defaults.................... 8-3 Menu Commands ........................ 8-4 Chapter 9 - Product Specifications Granit 1280i Industrial Corded Scanner Product Specifications.......... 9-1 Depth of Field Charts......................9-2 Typical Performance ..................... 9-2 Guaranteed Performance .................... 9-2 ............................9-3 Standard Connector Pinouts ....................

  • Page 13: Chapter 1 - Getting Started

    Honeywell bar code scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this guide.

  • Page 14: Reading Techniques

    Reading Techniques The Granit 1280i scanner has a bright red scanning line that corresponds to the scanner’s horizontal field of view. The scanning line is smaller when the scanner is closer to the code and larger when it is farther from the code. Symbologies with smaller bars or elements (mil size) should be read closer to the unit.

  • Page 15: Chapter 2 - Programming The Interface

    Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface - Plug and Play Plug and Play bar codes provide instant scanner set up for commonly used interfaces. Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect. RS232 Serial Port The RS232 Interface bar code is used when connecting to the serial port of a PC or terminal.

  • Page 16: Verifone ® Ruby Terminal Default Settings

    Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honeywell bioptic scanner auxiliary port configuration. This bar code sets the baud rate to 38400 bps and the data format to 8 data bits, no parity, 1 stop bit.

  • Page 17: Ncr Bioptic Aux Port Configuration

    NCR Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for an NCR bioptic scanner auxiliary port configuration. The fol- lowing prefixes are programmed for each symbology: Symbology Prefix Symbology Prefix UPC-A Interleaved 2 of 5 UPC-E Code 128 GS1 DataBar...

  • Page 18: Rs232 Modifiers

    RS232 Modifiers RS232 Baud Rate Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 9600. 1200 2400 4800 * 9600 19200 38400...

  • Page 19: Rs232 Word Length: Data Bits, Stop Bits, And Parity

    RS232 Word Length: Data Bits, Stop Bits, and Parity Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set, select 8 data bits per character.

  • Page 20: Rs232 Handshaking

    RS232 Handshaking RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. RTS/CTS Off: RTS/CTS is turned off so no data flow control is used, but RTS is still active. RTS/CTS Off, RTS Inactive: RTS/CTS is turned off so no data flow control is used and RTS is inactive. Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be asserted by the host.

  • Page 21: Rs232 Timeout

    RS232 Timeout When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the bar code below, then setting the timeout (from 1-65535 milli- seconds) by scanning digits from the inside back cover, then scanning Save.

  • Page 22: Nak Retries

    Timeout Retries This setting limits the number of Communication Timeout retries. If the Timeout Retries is set to 0, the transmission is terminated after the initial Communication Timeout. Scan the bar code below, then set the number of retries (from 0- 255) by scanning digits from the Programming Chart, then scanning Save.

  • Page 23: Rs232 Defaults

    RS232 Defaults If you want the custom RS232 default settings restored to your scanner, scan the RS232 Defaults bar code below. This resets the scanner to the custom default settings (see Setting Custom Defaults on page 1-2). If there are no custom defaults, it will reset the scanner to the factory default settings.

  • Page 24: Ncr Suffix

    Scanner to Bioptic Communication The following settings are used to set up communication between Honeywell scanners and bioptic scanners. Note: The scanner’s baud rate must be set to 38400 and the RS232 timeout must be set to 3000 in order to communicate with a bioptic scanner.

  • Page 25: Scanner-Bioptic Packet Mode

    Scanner-Bioptic Packet Mode Packet Mode On must be scanned to set the scanner’s format so it is compatible with a bioptic scanner. Default = Packet Mode Off. * Packet Mode Off Packet Mode On 2 - 11...
  • Page 26 2 - 12...

  • Page 27: Chapter 3 - Input/Output Settings

    Input/Output Settings Power Save Mode Power Save Mode allows you to automatically set the conditions under which the scanner idles, sleeps, and wakes up. When Off is selected, no power saving is used and the scanner remains powered on until the trigger is pressed. When Sleep Mode is selected, the scanner goes into sleep mode (powered off) after the time interval set using Power Save Mode Timeout...

  • Page 28: Beep On Bel Character

    * Power Up Beeper On - Scanner Beep on BEL Character You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On bar code below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off. *Beep on BEL Off Beep on BEL On Good Read and Error Indicators...

  • Page 29: Beeper Pitch - Good Read

    Beeper Pitch – Good Read The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium. Low (1600 Hz) * Medium (3200 Hz) High (4200 Hz) Beeper - Transmit Order The beeper transmit order determines when the good read beep occurs.

  • Page 30: Beeper Pitch - Error

    Vibrate Duration If you want to set the length for the good read vibration, scan the bar code below, then set the duration (from 100 - 2,000 milliseconds) by scanning digits from the inside back cover, then scanning Save. If you need to scan multiple bar codes in succession, you may wish to set a short duration time, since the trigger cannot be used until the vibration has ended.

  • Page 31: Number Of Beeps - Good Read

    Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1 - 9. The same number of beeps will be applied to the beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five beeps and five LED flashes in response to a good read.

  • Page 32: Laser Aimer - Scanning Duration

    Laser Aimer - Scanning Blinking Dot Laser Aimer - Scanning 3 Segment Line Laser Aimer - Scanning 5 Segment Line * Laser Aimer - Scanning 10 Segment Line Laser Aimer - Scanning Duration Use the Laser Aimer - Scanning Duration bar code to specify how long you want the Laser Aimer - Scanning Pattern remain on after the trigger is released.

  • Page 33: Laser Aimer - Good Read Duration

    * Laser Aimer - Good Read 10 Segment Line Laser Aimer - Good Read Duration Use the Laser Aimer - Good Read Duration bar code to specify how long you want the Laser Aimer - Good Read Pattern to remain on after a bar code has been successfully read. Scan the bar code below, then set the duration (from 0 - 65535 milliseconds) by scanning digits from the inside back cover, then scanning Save.

  • Page 34: Led Indicators

    LED Indicators The green and red LEDs can be programmed to be On or Off and at different brightness levels to indicate various scanner states. Use the following bar codes to program the LED indicators. LED Settings Default = Red LED On with Laser, Green LED On with Good Scan. Red LED Off Green LED Off Red LED On with Good Scan...

  • Page 35: Good Read Delay

    The following settings program the scanner’s behavior when it is out of the stand, or hand-held. Note: The Granit 1280i does not support In-Stand settings. It supports only the standard Honeywell Out-of-Stand settings. Caution: When working with Out-of-Stand settings, enable the settings you want before disabling those you do not want to use.

  • Page 36: Presentation Mode

    Presentation Mode When the scanner is in Presentation Mode, it automatically detects bar codes, then scans and transmits the data. To set the time period before the scanner can read the same bar code a second time use Reread Delay (page 3-11).

  • Page 37: Manual Activation Laser Timeout - Trigger Settings

    Manual Activation Laser Timeout - Trigger Settings You can set a timeout for the length of time the laser remains on and attempting to decode bar codes when the trigger is held down, and after it is released. Set the length (in milliseconds) for a timeout by scanning one of the following bar codes, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.

  • Page 38: Codegate

    ® CodeGate When CodeGate is On, the trigger is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding bar codes, but the bar code data is not transmitted until the trigger is pressed. When CodeGate is Off, bar code data is transmitted when it is decoded.

  • Page 39: End Character Activation After Good Read

    End Character Activation After Good Read After a bar code is successfully detected and read from the scanner, the illumination can be programmed either to remain on and scanning, or to turn off. When End Character Activation After Good Read is enabled, the illumination turns off and stops scanning after a good read.

  • Page 40: Deactivation Character

    Deactivation Character This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion Chart (Code Page 1252), page A-2, find the hex value that represents the character you want to use to terminate scanning. Scan the following bar code, then use the Programming Chart inside the back cover of this manual to read the alphanu-...

  • Page 41: Blinky Mode

    Right of Centering Window Blinky Mode When either Blinky Mode On or Blinky Always On/Continuous is scanned, the scanner blinks on and off at 50% duty cycle (250 milliseconds on, then 250 milliseconds off.) Default = Blinky Mode Off. * Blinky Mode Off Blinky Mode On Blinky Always On/ Continuous...

  • Page 42: Decode Security

    Decode Security This selection allows you to adjust the decode security needed while scanning. For good quality codes, choose Low to achieve fast scan speed. For codes prone to misreads, choose High. Default = Low. Note: Increasing the security level may decrease the scan speed. * Low Low/Medium Medium/High...

  • Page 43: Other Programming Selections

    indicating all lengths.) When calculating the length, you must count any programmed prefixes, suffixes, or formatted characters as part of the length (unless using 9999). 4. Character Match Sequences On the ASCII Conversion Chart (Code Page 1252), page A-2, find the Hex value that represents the character(s) you want to match.

  • Page 44: Output Sequence Editor

    The breakdown of the command line is shown below: SEQBLKsequence editor start command code identifier for Code 39 0012 A - Code 39 sample length (11) plus CR suffix (1) = 12 start character match for Code 39, 41h = “A” termination string for first code code identifier for Code 128 0013...

  • Page 45: Partial Sequence

    * Sequence Match Beeper On Partial Sequence If an output sequence operation is terminated before all your output sequence criteria are met, the bar code data acquired to that point is a “partial sequence.” Scan Discard Partial Sequence to discard partial sequences when the output sequence operation is terminated before completion.

  • Page 46: No Read

    No Read With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data Window (see page 7-2), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear. Default = Off.

  • Page 47: Chapter 4 - Data Editing

    Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along with the bar code data. This group of bar code data and additional, user-defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.

  • Page 48: To Clear One Or All Prefixes Or Suffixes

    Example: Add a Tab Suffix to All Symbologies Step 1. Scan Add Suffix. Step 2. Scan 9, 9 from the Programming Chart inside the back cover of this manual to apply this suffix to all symbologies. Step 3. Scan 0, 9 from the Programming Chart inside the back cover of this manual.

  • Page 49: Function Code Transmit

    Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained within the scanned data, the scanner transmits the function code to the terminal. Charts of these function codes are provided in Supported Interface Keys starting on page...

  • Page 50: Intercharacter Delay

    Intercharacter Delay An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay bar code below, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual.

  • Page 51: Intermessage Delay

    To remove this delay, scan the Interfunction Delay bar code, then set the number of delays to 0. Scan the Save bar code using the Programming Chart inside the back cover of this manual. Intermessage Delay An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission. Scan the Intermessage Delay bar code below, then scan the number of 5ms delays, and the Save bar code using the Programming Chart inside the back cover of this manual.
  • Page 52 4 - 6...

  • Page 53: Chapter 5 - Data Formatting

    Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in bar code data as it is scanned. The selections in the following pages are used only if you wish to alter the output.

  • Page 54: Other Programming Selections

    Step 5. Length Specify what length (up to 9999 characters) of data will be acceptable for this symbology. Scan the four digit data length from the Programming Chart inside the back cover of this manual. For example, 50 characters is entered as 0050. Note: 9999 indicates all lengths.

  • Page 55: Terminal Id Table

    Terminal ID Table Terminal Model(s) Terminal ID Serial RS232 True Data Format Editor Commands When working with the Data Format Editor, a virtual cursor is moved along your input data string. The following commands are used to both move this cursor to different positions, and to select, replace, and insert data into the final output. Send Commands Send all characters F1 Include in the output message all of the characters from the input message, starting from current cursor position,...
  • Page 56 Send all characters up to a particular character F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is moved forward to the “ss”...
  • Page 57 <CR> Insert symbology name B3 Insert the name of the bar code’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page A-1). Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-2 for decimal, hex and character codes.

  • Page 58: Move Commands

    B3 is the “Insert symbology name” command F4 is the “Insert a character multiple times” command 20 is the hex value for a space 01 is the number of times the space character is sent B4 is the “Insert bar code length” command F4 is the “Insert a character multiple times”...

  • Page 59: Search Commands

    F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 4567890ABCDEFGHIJ <CR> Move the cursor backward a number of characters F6 Move the cursor back “nn” characters from current cursor position. Syntax = F6nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved back.
  • Page 60 The data is output as: DEFGHIJ <CR> Search backward for a character F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page A-2 for decimal, hex and character codes.

  • Page 61: Miscellaneous Commands

    F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 37692 <CR> Search backward for a non-matching character E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non-“xx”...
  • Page 62 02 is the total count of characters to be replaced, plus the replacement characters (0 is replaced by CR, so total char- acters = 2) 30 is the hex value for 0 0D is the hex value for a CR (the character that will replace the 0) F1 is the “Send all characters”...

  • Page 63: Data Formatter

    ED is the “Check for a non-numeric character” command F1 is the “Send all characters” command 0D is the hex value for a CR If this bar code is read, the next data format, if there is one, will be used on this data. If there is no other format, the format fails and the raw data is output as 1234AB.

  • Page 64: Data Format Non-Match Error Tone

    Choose one of the following options. Default = Data Formatter On, Not Required, Keep Prefix/Suffix. * Data Formatter On, Not Required, Keep Prefix/Suffix Data Formatter On, Not Required, Drop Prefix/Suffix Data Format Required, Keep Prefix/Suffix Data Format Required, Drop Prefix/Suffix Data Format Non-Match Error Tone When a bar code is encountered that doesn’t match your required data format, the scanner normally generates an error tone.

  • Page 65: Single Scan Data Format Change

    Data Format 1 Data Format 2 Data Format 3 Single Scan Data Format Change You can also switch between data formats for a single scan. The next bar code is scanned using an alternate data format, then reverts to the format you have selected above (either Primary, 1, 2, or 3). For example, you may have set your device to the data format you saved as Data Format 3.
  • Page 66 5 - 14...

  • Page 67: All Symbologies

    Symbologies This programming section contains the following menu selections. Refer to Chapter 8 for settings and defaults. • All Symbologies • GS1 Emulation • China Post (Hong Kong 2 of 5) • GS1-128 • Codabar • Interleaved 2 of 5 •...

  • Page 68: Codabar

    Codabar <Default All Codabar Settings> Codabar On/Off * On Codabar Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/ Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Codabar Check Character Codabar check characters are created using different “modulos.”...

  • Page 69: Codabar Concatenation

    Validate Modulo 16 and Transmit Validate Modulo 7 CD, but Don’t Transmit Validate Modulo 7 CD and Transmit Validate CLSI, but Don’t Transmit Validate CLSI and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D”...
  • Page 70 Concatenation Timeout When searching for bar codes during concatenation, you may wish to set a delay used to find the next bar code. Set the length (in milliseconds) for this delay by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.

  • Page 71: Code 39

    Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Code 39 Start/Stop Characters Start/Stop characters identify the leading and trailing ends of the bar code. You may either transmit, or not transmit Start/ Stop characters. Default = Don’t Transmit. Transmit * Don’t Transmit Code 39 Check Character...

  • Page 72: Code 32 Pharmaceutical (Paraf)

    Code 39 Redundancy If you are encountering errors when reading Code 39 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.

  • Page 73: Full Ascii

    * Off Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will be interpreted as a single character. For example: $V will be decoded as the ASCII character SYN, and /C will be decoded as the ASCII character #. Default = Off.

  • Page 74: Interleaved 2 Of 5

    Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On NULL Characters Interleaved 2 of 5 requires an even number of characters. When an odd number of characters is present, it is due to NULL characters embedded in the bar code.

  • Page 75: Matrix 2 Of 5

    Validate and Transmit Interleaved 2 of 5 Redundancy If you are encountering errors when reading Interleaved 2 of 5 bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.
  • Page 76 When Check Character is set to Validate, but Don’t Transmit, the unit only reads Matrix 2 of 5 bar codes printed with a check character, but will not transmit the check character with the scanned data. When Check Character is set to Validate and Transmit, the scanner only reads Matrix 2 of 5 bar codes printed with a check character, and will transmit this character at the end of the scanned data.

  • Page 77: Nec 2 Of 5

    NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of 5 On/Off * Off Check Digit No Check Digit indicates that the scanner reads and transmits bar code data with or without a check digit. When Check Digit is set to Validate, but Don’t Transmit, the unit only reads NEC 2 of 5 bar codes printed with a check digit, but will not transmit the check digit with the scanned data.

  • Page 78: Code 93

    NEC 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93...

  • Page 79: Code 93 Code Page

    Code 93 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 93 Append This function allows the scanner to append the data from several Code 93 bar codes together before transmitting them to...

  • Page 80: Straight 2 Of 5 Industrial (Three-Bar Start/Stop)

    Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial On/Off * Off Straight 2 of 5 Industrial Redundancy If you are encountering errors when reading Straight 2 of 5 Industrial bar codes, you may want to adjust the redundancy count.

  • Page 81: Straight 2 Of 5 Iata (Two-Bar Start/Stop)

    Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA On/Off * Off Straight 2 of 5 IATA Redundancy If you are encountering errors when reading Straight 2 of 5 IATA bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.

  • Page 82: Code 11

    Code 11 <Default All Code 11 Settings> Code 11 On/Off * Off Check Digits Required This option sets whether 1 or 2 check digits are required with Code 11 bar codes. Default = Two Check Digits. One Check Digit * Two Check Digits Code 11 Redundancy If you are encountering errors when reading Code 11 bar codes, you may want to adjust the redundancy count.

  • Page 83: Code 128

    Maximum Message Length Code 128 <Default All Code 128 Settings> Code 128 On/Off * On 128 Group Separator Output If you wish to transmit embedded FNC1 characters as group separators (1B hex) with your Code 128 bar code output, scan the On bar code.

  • Page 84: Isbt 128 Concatenation

    Code 128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 0-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Code 128 Append This function allows the scanner to append the data from several Code 128 bar codes together before transmitting them to...
  • Page 85 Concatenation Timeout When searching for bar codes during concatenation, you may wish to set a delay used to find the next bar code. Set the length (in milliseconds) for this delay by scanning the following bar code, then setting the timeout (from 1-65535 milliseconds) by scanning digits from the Programming Chart, then scanning Save.
  • Page 86 ISBT 128 Predefined Concatenation Sequences On/Off The following selections allow you to enable or require the Predefined ISBT 128 Concatenation Sequences. If you scan Off, the predefined concatenation sequences are disabled. If you scan the Allow Predefined Sequence code, then the scanner will output only the data combination specified in the predefined concatenation sequence you selected.
  • Page 87 Step 1. Scan the 1st Left Identifier bar code, below. Step 2. Use the Programming Chart to scan 3, D (hex for “=”). Step 3. Scan Save. Step 4. Scan the 2nd Left Identifier bar code, below. Step 5. Use the Programming Chart to scan 4, 7 (hex for “G”).
  • Page 88 Allow User-Defined Sequence Require User-Defined Sequence Content Verification When the On bar code is scanned, the check character values are output along with the bar code data, thus allowing you to verify that the check character is in agreement with that calculated for the data stream. Default = Off. * Off Transmit Identifiers You may disable the transmission of the ISBT Code 128 data identifiers by scanning Off.

  • Page 89: Gs1-128

    GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off * On GS1-128 Application Identifier Parsing This allows a single GS1-128 bar code to be broken into multiple transmissions based on the presence of application iden- tifiers (AI) embedded in the bar code. To use this feature, first enable 128 Group Separator Output (page 6-17).

  • Page 90: Telepen

    GS1-128 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length Telepen <Default All Telepen Settings>...

  • Page 91: Upc-A

    Telepen Redundancy If you are encountering errors when reading Telepen bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the bar code.
  • Page 92 UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On UPC-A Number System The numeric system digit of a U.P.C. symbol is normally transmitted at the beginning of the scanned data, but the unit can be programmed so it will not transmit it.
  • Page 93 UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You must then turn on a 2 or 5 digit addenda listed on page 6-26. Default = Not Required. Required * Not Required UPC-A Addenda Separator When this feature is on, there is a space between the data from the bar code and the data from the addenda.

  • Page 94: Upc-A/Ean-13

    UPC-A/EAN-13 with Extended Coupon Code Use the following codes to enable or disable UPC-A and EAN-13 with Extended Coupon Code. When left on the default setting (Off), the scanner treats Coupon Codes and Extended Coupon Codes as single bar codes. If you scan the Allow Concatenation code, when the scanner sees the coupon code and the extended coupon code in a single scan, it transmits both as separate symbologies.

  • Page 95: Upc-A Number System 5 Addenda Required

    Default = Don’t Require Coupon Code. * Don’t Require Coupon Code Require Coupon Code UPC-A Number System 5 Addenda Required This setting programs the scanner to require any combination of a coupon code, a 2 digit addenda, or a 5 digit addenda on UPC-A bar codes that begin with a “5.”...

  • Page 96: Coupon Gs1 Databar Output

    Require Coupon Code or 5 Digit Addenda Require Coupon Code, 2 Digit Addenda, or 5 Digit Addenda Addenda Timeout You can set a time during which the scanner looks for a coupon code. If a coupon code is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A/EAN-13 with Extended Coupon Code...

  • Page 97: Upc-E0

    UPC-E0 <Default All UPC-E Settings> UPC-E0 On/Off Most U.P.C. bar codes lead with the 0 number system. To read these codes, use the UPC-E0 On selection. Default = On. * UPC-E0 On UPC-E0 Off UPC-E0 Expand UPC-E Expand expands the UPC-E code to the 12 digit, UPC-A format. Default = Off. * Off UPC-E0 Number System The numeric system digit of a UPC-A symbol is normally transmitted at the beginning of scanned data.
  • Page 98 UPC-E0 Number System and Check Digit UPC-E0 sample showing the number system and check digit: Number Check Digit UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default = Not Required. Required * Not Required UPC-E0 Addenda Separator...
  • Page 99 UPC-E0 Leading Zero This feature allows the transmission of a leading zero (0) at the beginning of scanned data. To prevent transmission, scan Off. Default = Off. * Off UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On...

  • Page 100: Ean/Jan-13

    EAN/JAN-13 <Default All EAN/JAN Settings> EAN/JAN-13 On/Off * On Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is selected, UPC-A bar codes are converted to 13 digit EAN-13 codes by adding a zero to the front. When Do not Convert UPC-A is selected, UPC-A codes are read as UPC-A. Default = Do not Convert UPC-A.
  • Page 101 EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default = Off for both 2 Digit and 5 Digit Addenda. 2 Digit Addenda On * 2 Digit Addenda Off 5 Digit Addenda On * 5 Digit Addenda Off EAN/JAN-13 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-13 bar codes that have addenda.
  • Page 102 Default = Don’t Require 2 Digit Addenda. 2 Digit * Don’t Require Addenda 2 Digit Addenda Require EAN-13 Beginning with 290 Addenda Required This setting programs the scanner to require a 5 digit addenda only on EAN-13 bar codes that begin with “290.” The follow- ing settings can be programmed: Require 5 Digit Addenda: All EAN-13 bar codes that begin with “290”...
  • Page 103 Require 2 Digit Addenda Require 5 Digit Addenda Require 2 or 5 Digit Addenda EAN-13 Beginning with 414/419 Addenda Required This setting programs the scanner to require any combination of a 2 digit addenda or a 5 digit addenda on EAN-13 bar codes that begin with a “414”...
  • Page 104 Don’t Require Addenda: If you have selected Require Addenda, and you want to disable this feature, scan Don’t Require Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/JAN-13 Addenda Required. Default = Don’t Require Addenda. * Don’t Require Addenda Require 2 Digit Addenda Require 5 Digit Addenda...
  • Page 105 Don’t Require 5 Digit Addenda: If you have selected Require 5 Digit Addenda, and you want to disable this feature, scan Don’t Require 5 Digit Addenda. EAN-13 bar codes are transmitted, depending on the setting you are using for EAN/ JAN-13 Addenda Required.

  • Page 106: Isbn Translate

    Addenda Timeout You can set a time during which the scanner looks for a coupon code. If a coupon code is not found within this time period, the data can be either transmitted or discarded, based on the setting you are using for UPC-A/EAN-13 with Extended Coupon Code UPC-A Number System 4 Addenda...

  • Page 107: Issn Translate

    ISBN Reformat In normal use, the first two or three digits of an EAN-13 bar code identify the country of origin. The country prefixes are 978 and 979. To reformat ISBN codes so the country prefix is dropped out, scan the Reformat On bar code below. Default = Reformat Off.

  • Page 108: Ean/Jan-8

    EAN/JAN-8 <Default All EAN/JAN-8 Settings> EAN/JAN-8 On/Off * On EAN/JAN-8 Check Digit This selection allows you to specify whether the check digit should be transmitted at the end of the scanned data or not. Default = On. * On EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data.
  • Page 109 * 5 Digit Addenda Off EAN/JAN-8 Addenda Required When Required is scanned, the scanner will only read EAN/JAN-8 bar codes that have addenda. Default = Not Required. Required * Not Required EAN/JAN-8 Addenda Separator When this feature is On, there is a space between the data from the bar code and the data from the addenda. When turned Off, there is no space.

  • Page 110: Msi

    EAN/JAN-8 Redundancy If you are encountering errors when reading EAN/JAN-8 bar codes, you may want to adjust the redundancy count. Redun- dancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors. Note that the higher the redundancy count, the longer it will take to decode the ba code.
  • Page 111 Validate 2 Type 10 Characters, but Don’t Transmit Validate 2 Type 10 Characters and Transmit Validate Type 11 then Type 10 Character, but Don’t Transmit Validate Type 11 then Type 10 Character and Transmit Disable MSI Check Characters MSI Redundancy If you are encountering errors when reading MSI bar codes, you may want to adjust the redundancy count.

  • Page 112: Plessey Code

    Plessey Code < Default All Plessey Code Settings > Plessey Code On/Off * Off Plessey Check Character No Check Character indicates that the scanner reads and transmits bar code data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Plessey bar codes printed with a check character, but will not transmit the check character with the scanned data.

  • Page 113: Gs1 Databar Omnidirectional

    Plessey Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length GS1 DataBar Omnidirectional <...

  • Page 114: Gs1 Databar Limited

    GS1 DataBar Limited < Default All GS1 DataBar Limited Settings > GS1 DataBar Limited On/Off * On GS1 DataBar Limited Redundancy If you are encountering errors when reading GS1 DataBar Limited bar codes, you may want to adjust the redundancy count.

  • Page 115: Gs1 Databar Expanded

    GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On GS1 DataBar Expanded Redundancy If you are encountering errors when reading GS1 DataBar Expanded bar codes, you may want to adjust the redundancy count.

  • Page 116: Trioptic Code

    Trioptic Code Note: If you are going to scan Code 32 Pharmaceutical codes (page 6-6), Trioptic Code must be off. Trioptic Code is used for labeling magnetic storage media. * Off Trioptic Code Redundancy If you are encountering errors when reading Trioptic bar codes, you may want to adjust the redundancy count. Redundancy adjusts the number of times a bar code is decoded before transmission, which may reduce the number of errors.

  • Page 117: China Post (Hong Kong 2 Of 5)

    GS1 Code Expansion Off EAN8 to EAN13 Conversion * GS1 Emulation Off China Post (Hong Kong 2 of 5) <Default All China Post (Hong Kong 2 of 5) Settings> China Post (Hong Kong 2 of 5) On/Off * Off China Post (Hong Kong 2 of 5) Redundancy If you are encountering errors when reading China Post (Hong Kong 2 of 5) bar codes, you may want to adjust the redun- dancy count.
  • Page 118 China Post (Hong Kong 2 of 5) Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page 6-1) for additional information. Minimum and Maximum lengths = 1-80. Minimum Default = 3, Maximum Default = 80. Minimum Message Length Maximum Message Length 6 - 52...

  • Page 119: Chapter 7 - Utilities

    Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission of a Code I.D. before the decoded symbology. (See the Symbology Charts, beginning on page A-1) for the single character code that identifies each symbology.) This action first clears all current prefixes, then programs a Code I.D.

  • Page 120: Application Plug-Ins (Apps)

    Application Plug-Ins (Apps) Any apps that you are using can be turned off or on by scanning the following bar codes. Apps are stored in groups: Decoding, and Formatting. You can enable and disable these groups of apps by scanning that group’s On or Off bar code below. You can also scan the List Apps bar code to output a list of all your apps.

  • Page 121: Installing Ezconfig-Scanning From The Web

    7. Using Explorer, go to the c:\windows\temp file. 8. Double click on the Setup.exe file. Follow the screen prompts to install the EZConfig-Scanning program. 9. If you’ve selected the defaults during installation, you can click on Start Menu-All Programs-Honeywell-EZConfig- Scanning.
  • Page 122 7 - 4...

  • Page 123: Chapter 8 - Serial Programming Commands

    Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the serial commands and the programming bar codes will program the scanner. For complete descriptions and examples of each serial programming com- mand, refer to the corresponding programming bar code in this manual.

  • Page 124: Responses

    Data Field Usage When a query is used in place of the Data field, the query applies only to the specific command identified by the Tag and SubTag fields. Concatenation of Multiple Commands Multiple commands can be issued within one Prefix/Storage sequence. Only the Tag, SubTag, and Data fields must be repeated for each command in the sequence.

  • Page 125: Serial Trigger Commands

    the Minimum Message Length (MIN) is set to 2 characters; the Maximum Message Length (MAX) is set to 60 characters; and the Default setting (DFT) has no value. Serial Trigger Commands You can activate and deactivate the scanner with serial trigger commands. The trigger is activated and deactivated by sending the following commands: Activate: SYN T CR...

  • Page 126: Menu Commands

    PAP232 OPOS Mode OPOS Mode PAPOPS Plug and Play Codes Verifone Ruby Terminal PAPRBY Gilbarco Terminal PAPGLB Honeywell Bioptic Aux Port PAPBIO Datalogic Magellan Aux Port PAPMAG NCR Bioptic Aux Port PAPNCR Wincor Nixdorf Terminal PAPWNX Wincor Nixdorf Beetle PAPBTL...
  • Page 127 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry RS232 Handshaking *RTS/CTS Off 232CTS0 Flow Control, No Timeout 232CTS1 Character-Based Flow Control, No 232CTS7 Timeout Two-Direction Flow Control 232CTS2 Flow Control with Timeout 232CTS3 Character-Based Flow Control with 232CTS9 Timeout *RTS/CTS Off, RTS Inactive...
  • Page 128 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Power Up Beeper Power Up Beeper Off - Scanner BEPPWR0 *Power Up Beeper On - Scanner BEPPWR1 Beep on BEL Character Beep on BEL On BELBEP1 *Beep on BEL Off BELBEP0 Beeper - Good Read BEPBEP0...
  • Page 129 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Aimer Delay 200 milliseconds SCNDLY200 400 milliseconds SCNDLY400 *Off (no delay) SCNDLY0 User-Specified Aimer Delay Range 0 - 4,000 ms SCNDLY#### LED Indicators Red LED Off LEDFN10 Green LED Off LEDFN20 Red LED On with Good Scan...
  • Page 130 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Character Activation Mode *Off HSTCEN0 3-12 HSTCEN1 3-12 Activation Character (Range 0- HSTACH### 3-12 255) *18 [CAN] Do Not End Character Activation HSTCGD0 3-13 After Good Read *End Character Activation After HSTCGD1 3-13...
  • Page 131 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Prefix/Suffix Selections Add CR Suffix to All Symbologies VSUFCR Prefix Add Prefix PREBK2## Clear One Prefix PRECL2 Clear All Prefixes PRECA2 Suffix Add Suffix SUFBK2## Clear One Suffix SUFCL2 Clear All Suffixes SUFCA2...
  • Page 132 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Single Scan Data Format Change Single Scan-Primary VSAF_0 5-13 Data Format Single Scan-Data Format 1 VSAF_1 5-13 Single Scan-Data Format 2 VSAF_2 5-13 Single Scan-Data Format 3 VSAF_3 5-13 Symbologies...
  • Page 133 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Code 39 Message Length Minimum (1 - 80) *3 C39MIN## Maximum (1 - 80) *80 C39MAX## Code 39 Append *Off C39APP0 C39APP1 Code 32 Pharmaceutical (PARAF) *Off C39B320 C39B321 Code 39 Full ASCII...
  • Page 134 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Code 93 Default All Code 93 C93DFT 6-12 Settings C93ENA0 6-12 C93ENA1 6-12 Code 93 Redundancy Redundancy C93VOT## 6-12 Code 93 Message Length Minimum (1 - 80) *3 C93MIN## 6-13 Maximum (1 - 80) *80...
  • Page 135 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry ISBT 128 *Off ISBENA0 6-18 ISBENA1 6-18 Concatenation Timeout DLYCCT 6-19 ISBT128 Predefined Concatenation * Donation ID Number (001) ISBPCS0 6-19 Sequences and ABO/RhD Blood Groups (002) Donation ID Number (001) and ISBPCS1 6-19...
  • Page 136 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Telepen Default All Telepen TELDFT 6-24 Settings *Off TELENA0 6-24 TELENA1 6-24 Telepen Output *AIM Telepen Output TELOLD0 6-24 Original Telepen Output TELOLD1 6-24 Telepen Redundancy Redundancy TELVOT## 6-25 Telepen Message Length...
  • Page 137 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry UPC-A Number System 5 Addenda * Don’t Require Coupon Code/ ARQSY50 6-29 Required Addenda Require 2 Digit Addenda ARQSY51 6-29 Require 5 Digit Addenda ARQSY52 6-29 Require 2 or 5 Digit Addenda ARQSY53 6-29 Require Coupon Code...
  • Page 138 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry EAN/JAN-13 Check Digit E13CKX0 6-34 E13CKX1 6-34 EAN/JAN-13 2 Digit Addenda 2 Digit Addenda On E13AD21 6-35 *2 Digit Addenda Off E13AD20 6-35 5 Digit Addenda On E13AD51 6-35 *5 Digit Addenda Off...
  • Page 139 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry ISSN Translate *Off E13ISS0 6-41 E13ISS1 6-41 Reformat On E13ISR1 6-41 *Reformat Off E13ISR0 6-41 EAN/JAN-8 Default All EAN/ EA8DFT 6-42 JAN 8 Settings EA8ENA0 6-42 EA8ENA1 6-42 EAN/JAN-8 Check Digit EA8CKX0...
  • Page 140 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Plessey Check Char. *No Check Char. PLSCHK0 6-46 Validate, But Don’t PLSCHK1 6-46 Transmit Validate, PLSCHK2 6-46 and Transmit Plessey Redundancy Range (0 - 10) *0 PLSVOT## 6-46 Plessey Message Length Minimum (1 - 80) *3...
  • Page 141 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Utilities Add Code I.D. Prefix to All Symbologies (Temporary) PRECA2,BK2995C80! Show Software Revision REVINF Show Data Format DFMBK3? Test Menu TSTMNU1 *Off TSTMNU0 Application Plug-Ins (Apps) *Decoding Apps On PLGDCE1 Decoding Apps Off PLGDCE0...
  • Page 142 8 - 20...

  • Page 143: Chapter 9 - Product Specifications

    Product Specifications Granit 1280i Industrial Corded Scanner Product Specifications Parameter Specification Dimensions (Typical): Height 7.7 in. (19.45cm) Length 5.2 in. (13.31cm) Width 2.9 in. (7.5cm) Weight 11.8 oz. (335g) Scan Line: Peak Wavelength Laser 650nm IEC 60825-1: “Class 2” Optical Power Laser <1mW...

  • Page 144: Depth Of Field Charts

    Depth of Field Charts Typical Performance Focus Near Distance Far Distance Paper 18.5 7.5 mil 32.5 10 mil 10.2 82.6 62.5 15 mil 10.2 158.8 83.4 20 mil 11.4 211.8 13.5 178.5 55 mil 34.3 453.4 36.5 183.5 100 mil 92.7 466.1 Retro-reflective...
  • Page 145 Focus Near Distance Far Distance Minimum Resolution: 5 mil 9 - 3...

  • Page 146: Standard Connector Pinouts

    Standard Connector Pinouts Serial Output 10 Pin RJ41 Modular Plug - connects to the scanner Cable shield Cable select Supply ground Transmit data Receive data - serial data to scanner +5V power 9 - 4...

  • Page 147: Chapter 10 - Maintenance

    The interface cable is designed to be field replaceable. • Order replacement cables from Honeywell or from an authorized distributor. • When ordering a replacement cable, specify the cable part number of the original interface cable.

  • Page 148: Replacing An Interface Cable

    Replacing an Interface Cable 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s cable from the terminal or computer. 3. Unscrew the locking plate on the bottom of the scanner. 4. Slide the locking plate away from the connector and pull the cable out of the scanner. 5.

  • Page 149: Chapter 11 - Customer Support

    Limited Warranty Honeywell International Inc. ("HII") warrants its products to be free from defects in materials and workmanship and to conform to HII’s published specifications applicable to the products purchased at the time of shipment. This warranty does not cover any HII product which is (i) improperly installed or used;...
  • Page 150 HII extends these warranties only to the first end-users of the products. These warranties are non-transferable. The duration of the limited warranty for the Granit 1280i scanner is three (3) years. 11 - 2...

  • Page 151: Symbology Charts

    Refer to Data Editing beginning on page 4-1 and Data Formatting beginning on page 5-1 for information about using Code ID and AIM ID. Linear Symbologies Honeywell Possible modifiers Symbology All Symbologies Codabar Code 11 Code 128 0, 1, 2, 4 Code 32 Pharmaceutical (PARAF) <...

  • Page 152: Postal Symbologies

    Honeywell Possible modifiers Symbology UPC-A UPC-A with Add-On UPC-A with Extended Coupon Code UPC-E UPC-E with Add-On UPC-E1 Add Honeywell Code ID 5C80 Add AIM Code ID 5C81 Add Backslash 5C5C Batch mode quantity Postal Symbologies Honeywell Possible modifiers Symbology...

  • Page 153: Lower Ascii Reference Table

    Non-printable ASCII control Keyboard Control + ASCII (CTRL+X) Mode characters Windows Mode Control + X Mode On (KBDCAS2) Char Control + X Mode Off (KBDCAS0) CTRL + X CTRL + X function Insert CTRL+ N CTRL+ O Open CTRL+ P Print Home CTRL+ Q...
  • Page 154 Printable Characters (Continued) Character Character Character < > ⌂ Extended ASCII Characters CP 1252 ASCII Alternate Extended PS2 Scan Code ↑ € Ç 0x48 up arrow ↓ ü 0x50 down arrow → ‚ é 0x4B right arrow ← ƒ â 0x4D left arrow „...
  • Page 155 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code ¢ ó Left Ctrl 0x1D £ ú Left Shift 0x2A ¤ ñ Right Shift 0x36 ¥ Ñ Print Screen ¦ ª 0x0F § º Shift Tab 0x8F ¨ ¿...
  • Page 156 Extended ASCII Characters (Continued) CP 1252 ASCII Alternate Extended PS2 Scan Code Ö ╓ × ╫ Ø ╪ Ù ┘ Ú ┌ Û █ Ü ▄ Ý ▌ Þ ▐ ß ▀ à α á ß â Γ ã π ä...

  • Page 157: Iso 2022/Iso 646 Character Replacements

    (standard ASCII) Automatic National Character ISO/IEC 2022 2 (default) Replacement Binary Code page Default “Automatic National Character replacement” will select the below Honeywell Code Page options for Code128, Code 39 and Code 93. United States ISO/IEC 646-06 Canada ISO /IEC 646-121...
  • Page 158 à â ç ê î ô é ù è û à â ç ê É ô é ù è û ⎯ ¥ ⎯ ¥ £ ˜ £ à ° ç § µ é ù è ¨ § Ä Ö Ü ä...

  • Page 159: Unicode Key Maps

    Unicode Key Maps 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 4B 50 55 5A 5F 64 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 4C 51 56 5B 60 65 1F 20 21 22 23 24 25 26 27 28 29...
  • Page 160 A - 10...
  • Page 161 Sample Symbols UPC-A 0 123456 7890 Interleaved 2 of 5 1234567890 EAN-13 9 780330 290951 Code 128 Code 128 Code 39 BC321 Codabar A13579B Code 93 123456-9$...
  • Page 162 Programming Chart...
  • Page 163 Programming Chart Save Discard Reset Note: If you make an error while scanning the letters or digits (before scanning Save), scan Discard, scan the correct letters or digits, and Save again.
  • Page 164 Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com 1280i-UG Rev B 7/14...

Table of Contents