hit counter script
Download
Share
Print this page
Toro 132-9543 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower Accessories
  5. 132-9543
  6. Installation instructions manual
Toro 132-9543 Installation Instructions Manual

Toro 132-9543 Installation Instructions Manual

Console kit for greensmaster 3320 or 3420 series triflex traction unit
Hide thumbs

Advertisement

Quick Links

Download this manual
Console Kit
Greensmaster
Model No. 132-9543
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.
1. Engine speed (high)
2. Engine speed (low)
3. Lower and engage the reels
4. Raise and disengage the reels
5. Traction unit (transport)
6. Traction unit (mow)
© 2016—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
3320 or 3420 Series TriFlex
132-9548
7. Traction unit (neutral)
8. Reel (transport)
9. Reel (mow)
10. Reel (backlaping)
11. Move forward
Register at www.Toro.com.
Form No. 3397-700 Rev A
®
Traction Unit
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3397-700* A
Printed in the USA

Advertisement

loading

Related Manuals for Toro 132-9543

Summary of Contents for Toro 132-9543

  • Page 1 Greensmaster ® 3320 or 3420 Series TriFlex ® Traction Unit Model No. 132-9543 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.

  • Page 2: Table Of Contents

    132-9550 1. Choke 3. Engine (run) 2. Engine (start) 4. Engine (stop) Installation Loose Parts Use the chart below to verify that all parts have been shipped. Description Qty. – No parts required Prepare the machine. – No parts required Remove the console.

  • Page 3: Console Assembly

    Preparing the Machine Removing the Throttle Assembly Note: Set aside all of the items that you remove from this 1. Move the machine to a level workspace. procedure. 2. Shut off the engine, set the parking brake, and remove the key from the ignition switch. 1.
  • Page 4 Removing the Mow-Control Assembly Removing the Function-Control Assembly 1. Remove and set aside the knob from the mow-control shaft (Figure Note: Set aside all of the items that you remove in the following procedure unless otherwise instructed. 1. Remove the 2 bolts and nut clip securing cable clamp and shim to the console assembly (Figure Figure 4...
  • Page 5 Figure 7 1. Retaining nut 3. Proximity sensor 2. Washer Figure 9 1. Bolt 3. Nut 6. Remove the knob from the function lever (Figure 2. Function-control assembly Disconnecting the Choke Cable 1. Disconnect the cable from the choke control on the engine.
  • Page 6 Removing the Switches and Indicators Note: Set aside all of the items that you remove from this procedure. 1. Remove the retaining ring to remove the display from the console assembly (Figure 10). Figure 12 Cutaway View 1. Hour meter 3.
  • Page 7 Removing the Console Assembly Installing the Kit Set aside all of the items that you remove from this procedure. Installing the Console Assembly 1. Remove the 2 carriage bolts and flange nuts that secure the console assembly to the console bracket (Figure 14).

  • Page 8: Speed Nut

    Installing the Mow-Control Assembly Installing the Choke Assembly 1. Use the 2 bolts (#10 x 1/2 inch) and locknuts to secure Gas Engine Only the joystick assembly to the console (Figure 17). 1. Follow the original cable routing to route the new choke cable and secure it to the machine with cable ties (Figure...

  • Page 9: Bolt (#10 X 1/2 Inch)

    Installing the Slot Cover 2. Use the locknut, flat washer, spacer tube, and bolt that you removed earlier to secure the handle assembly to the bracket (Figure 22). Diesel Engine Only Use the bolt (#10 x 3/8 inch) to secure the slot cover to the console (Figure 20).

  • Page 10: Bolt (1/4 X 5/8 Inch)

    Installing the Neutral-Lock Cable Installing the Switches and Indicators 1. Remove the original cable and route the new cable in 1. Press hour meter into the cutout until it is secure with its place. the retainer (Figure 26). 2. Connect the neutral-lock cable to the pedal shifter (Figure 24).

  • Page 11: Bolt (#10 X 3/8 Inch)

    Completing the Install 1. Use the 8 bolts that you removed earlier to secure the console cover to the console assembly (Figure 31). Figure 28 1. Display 2. Retaining ring Figure 31 4. Use the retaining nut you removed earlier to secure the ignition switch to the console assembly (Figure 29).
  • Page 12 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.