Page 4
3.装置への取り付け・取り外し 下記の手順にて装置に取り付けを行ってください。 ● 取り付ける装置の説明書を参照し、「安全上のご注意」、「取り扱い上のご注意」を守って 取り付け・取り外しを行ってください。 ※本製品を取り付けることにより、本体外形寸法が以下となります。 175.0 mm (幅) X 492.0 mm (奥行き) X 367.0 mm (高さ) (突起物含まず) フロントベゼル 1. フロントベゼルを開いて、手前に引き、 取り外してください。 ② ① デバイスドア 2. デバイスドアを開いて、上方向に スライドさせ取り外してください。 ② ① 3. 前項のデバイスドアの取り外しと 防塵ドア ...
Page 5
4. アクセントカバーのツメ4箇所を押してフロントベゼルから外します。 矢印の方向にツメを押して アクセントカバーを外す。 ① ① アクセントカバー ② ① ① 5. 前項のアクセントカバーの取り外しと 逆の手順で防塵カバーをフロントベゼルに 取り付けます。 ② 防塵カバー ① 5 ...
N8146-44 Dust Proof Kit with Sensor User's Guide Preface Thank you very much for your purchase of this product. The guide is intended to allow you to install and use the product correctly and safely. Read the guide carefully before handling the product.
Safety Precautions Observe the following notes to use the product safely. WARNING If smoke, odor, or noise is present, immediately turn off the server and disconnect the power plug from the outlet, then contact the store where you purchased the product or your maintenance service company. Using the server in such conditions may cause a fire.
Transfer to Third Party Make sure to provide all accessories including this manual along with the product to a third party. Disposal Dispose of this product according to all national laws and regulations. Dispose of this product as plastic garbage. 1.Notes on Using the Product ●This product is dedicated to Express5800/T110f-E server.
Page 15
Note: The outer dimension of NEC Express5800/T110f-E is as follows after the bezel is installed. 175.0 mm (Width) × 492.0 mm (Depth) × 367.0 mm (Height) (Projection excluded) 1.
Page 16
4. Push the four claws as shown in figure below then remove the accent cover. Push four claws ① ① Accent Cover ② ① ① 5. Install the dust proof cover as shown in figure below. ② Dust Proof Cover ① ...
Page 17
6. Install the sensor to front bezel as shown in figure below. Install the sensor by adjusting the positioning pins to the positioning on the front bezel. ● Be aware of the side and orientation of the sensor. If the sensor is installed incorrectly, it cannot work properly.
Page 18
8. Attach the sensor cable to the front bezel. 9. Remove the side cover, holding it firmly. Pull in the sensor cable from the hole of the server front side, and install the front bezel. Insert the three hinges of front bezel into the holes of server.
Page 19
10. Connect the sensor cable to the Motherboard. Connector for the Sensor cable 11. Stick the nameplate on the front bezel shown by the slant lines in the figure below. Nameplate (T110f-E) 4.Filter Monitor Software Install Regarding the installation procedure of the Filter Monitor Software, refer to “Filter Monitor Software Instruction Guide”...
Page 20
5.Replacement of Dust-proof Filter The service life of dust-proof filter is six months (recommended) or one year (maximum). The life time depends on usage environment. Use N8147-27 Dust filter for tower for replacement. ●If the server is operated for long time without replacing the filter, a malfunction may be generated due to the temperature rise of the device caused by clogged dust.
Page 21
2.Replacement of dust-proof filter 2.1 Pull the tab and remove the dust proof filter. Dust Proof Filter 2.2 Install the dust proof filter in reverse order of removal procedure. ● Be sure to set the dust proof filter without interstices. ●...
Page 22
Remarks (1) No part of this manual may be reproduced in any form without the prior written permission of NEC Corporation. (2) The contents of this User's Guide may be revised without prior notice. (3) The contents of this User's Guide shall not be copied or altered without the prior written permission of NEC Corporation.