Toro Z Master G3 Setup Instructions
Riding mower with 60in or 72in turbo force® side discharge mower
Hide thumbs
Also See for Z Master G3:
- Operator's manual (72 pages) ,
- Setup instruction (17 pages) ,
- Operator's manual (68 pages)
Advertisement
Z Master
with 60in or 72in TURBO FORCE
Model No. 74975—Serial No. 310000001 and Up
Model No. 74977—Serial No. 310000001 and Up
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
9
10
1
Unfolding the Crate
No Parts Required
Procedure
Refer to the Packaging Crate Instructions included with
the machine.
© 2010—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
G3 Riding Mower
Description
No parts required
No parts required
No parts required
No parts required
No parts required
Bolt (1/2 x 3-1/4 inch)
Locknut (1/2 inch)
Number 2 general purpose lithium base
or molybdenum base grease. (Purchase
separately.)
No parts required
No parts required
Operator's Manual
Engine Owner's Manual
Registration Card
Operator training material
Key
Register at www.Toro.com.
®
Side Discharge Mower
Qty.
–
Unfold the crate.
–
Check the tire pressure.
–
Charge the battery.
–
Check the engine oil level.
–
Add fuel to the machine.
1
Install ROPS Hardware
1
1 tube
Check the machine for grease.
–
Prepare the side discharge chute.
Check the machine before delivery to
–
the customer.
1
1
1
Delivering the machine to the customer.
1
2
2
Checking the Tire Pressure
No Parts Required
Procedure
Pressure: 13 psi (90 kPa)
Note: The front caster wheel is a semi-pneumatic tire
and does not need to be checked.
Check the air pressure in the drive tires.
Form No. 3365-290 Rev A
Setup Instructions
Use
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro Z Master G3
Summary of Contents for Toro Z Master G3
- Page 1 Note: The front caster wheel is a semi-pneumatic tire the machine. and does not need to be checked. Check the air pressure in the drive tires. Register at www.Toro.com. © 2010—The Toro® Company Original Instructions (EN) 8111 Lyndale Avenue South Printed in the USA. Bloomington, MN 55420...
-
Page 2: Charging The Battery
Figure 1 Figure 2 Charging the Battery Checking the Engine Oil Level No Parts Required No Parts Required Procedure Procedure Before you start the engine and use the machine, check WARNING the oil level in the engine crankcase; refer to Servicing Charging the battery produces gasses that can the Engine Oil Level in Operator’s Manual. - Page 3 4. Align the center hole over the mounting pin that points straight up on the mower as shown in Figure 3. g013437 Figure 4 1. LPG fuel hose connection 3. Fuel gauge G013619 fitting Figure 3 2. Tank valve 1. Tank collar 3.
- Page 4 G009029 Figure 6 2. Check the grease for the pump drive belt idler arm. G013506 Figure 5 1. Locknut (1/2 inch) 3. Bolt (1/2 x 3-1/4 inch) 2. ROPS Checking the Machine for Figure 7 Grease Parts needed for this procedure: 3.
-
Page 5: Checking The Side Discharge Chute
Checking the Side Discharge Chute No Parts Required Procedure If there are plastic ties holding the side discharge chute up, remove them and lower the chute into place. WARNING Figure 9 An uncovered discharge opening could allow the 1. Grass Deflector 4. - Page 6 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator’s Manual for instructions on performing these procedures.
- Page 7 Delivering the Machine to the Customer Parts needed for this procedure: Operator’s Manual Engine Owner’s Manual Registration Card Operator training material Procedure At delivery, Fill in the model and serial number and complete the items listed in the following table and initial each when finished.
- Page 8 Make sure that the customer receives the Operator’s Manual, Engine Owner’s Manual, Set Up Instructions, and operator training material. Make sure the customer knows the Parts Catalog is available at www.Toro.com. Assist the customer in loading the mower. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.