1 Safety Precautions 1.1. General Guidelines 1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. 2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec- trostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor [chip] components.
2.2. About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
3 Service Navigation 3.1. PCB Layout Board Name Function Board Name Function Power Supply Remote receiver, Power LED, C.A.T.S. sensor DC-DC Converter, Tuner Data Driver (Lower Right) Speaker out, AV Terminal, HDMI in, SD Card Data Driver (Lower Left) Digital Signal Processor, PEAKS-sLD Scan Drive Format Converter, Plasma AI, Sub-Field Processor Sustain Drive...
4 Specifications Power Source AC 220-240 V, 50 / 60 Hz (K/M/V) AC 110-240 V, 50 / 60 Hz (P) Power Consumption Average use : 230 W Standby condition : 0.45 W Display panel Aspect Ratio 16:9 Visible screen size 106 cm (diagonal) 921 mm (W) ×...
Page 9
Dimensions (W × H × D) 1,029 mm × 704 mm × 307 mm (With Pedestal) 1,029 mm × 661 mm × 93 mm (TV only) Mass 25.5 kg Net (With Pedestal) 24.0 kg Net (TV only) Note • Design and Specifications are subject to change without notice. Mass and Dimensions shown are approximate.
5 Service Mode 5.1. How to enter into Service Mode While pressing [VOLUME ( - )] button of the main unit, press [RECALL] button of the remote control three times within 2 seconds. 5.1.1. Key command [1] button...Main items Selection in forward direction [2] button...Main items Selection in reverse direction [3] button...Sub items Selection in forward direction [4] button...Sub items Selection in reverse direction...
Page 11
5.1.2. Contents of adjustment mode • Value is shown as a hexadecimal number. • Preset value differs depending on models. • After entering the adjustment mode, take note of the value in each item before starting adjustment. 5.1.3. How to exit Switch off the power with the [POWER] button on the main unit or the [POWER] button on the remote control.
5.2. Option - Mirror Picture can be reversed left and right or up and down. 00 : Default (Normal picture is displayed) 01 : Picture is reversed left and right. 02 : Picture is reversed up and down. Hint : If the defective symptom (e.g. Vertical bar or Horizontal bar) is moved by selection of this mirror, the possible cause is in A-board.
5.4. Hotel mode 1. Purpose Restrict a function for hotels. item Function 2. Access command to the Hotel mode setup menu Hotel Mode Select hotel mode ON/OFF In order to display the Hotel mode setup menu, please Initial INPUT Select input signal modes. enter the following command (within 2 second).
5.5. Data Copy by SD Card 5.5.1. Purpose (a) Board replacement (Copy the data when exchanging A-board): When exchanging A-board, the data in original A-board can be copied to SD card and then copy to new A-board. (b) Hotel (Copy the data when installing a number of units in hotel or any facility): When installing a number of units in hotel or any facility, the data in master TV can be copied to SD card and then copy to other TVs.
Page 15
5.5.3. Data copy from TV set to SD Card 1. Turn on the TV set. 2. Insert SD card with a startup file (pwd file) to SD slot. On-screen Display will be appeared according to the startup file automatically. 3. Input a following password for (a) or (b) by using remote control. (a) For Board replacement : 2770 (b) For Hotel : 4850 Data will be copied from TV set to SD card.
Page 16
5.5.4. Data copy from to SD Card to TV set 1. Turn on the TV set. 2. Insert SD card with Data to SD slot. On-screen Display will be appeared according to the Data folder automatically. 3. Input a following password for (a) or (b) by using remote control. (a) For Board replacement : 2771 (b) For Hotel : 4851 Data will be copied from SD card to TV set.
6 Troubleshooting Guide Use the self-check function to test the unit. 1. Checking the IIC bus lines 2. Power LED Blinking timing 6.1. Check of the IIC bus lines 6.1.1. How to access Self-check indication only: Produce TV reception screen, and while pressing [VOLUME ( - )] button on the main unit, press [OK] button on the remote control for more than 3 seconds.
6.2. Power LED Blinking timing chart 1. Subject Information of LED Flashing timing chart. 2. Contents When an abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by the number of blinks of the Power LED on the front panel of the unit.
6.3. No Power First check point There are following 2 states of No Power indication by power LED. 1. No lit 2. Red is lit then turns red blinking a few seconds later. (See 6.2.)
7 Disassembly and Assembly Instructions 7.1. Remove the Rear cover 7.4. Remove Side terminal cover and the Side shield metal 1. See PCB Layout (Section 3) 7.2. Remove the AC inlet , ×1 , ×1 1. Remove the screws (×2 2.
7.5. Remove the Tuner unit 7.7. Remove the Speakers 1. Remove the Side terminal cover and the Side shield 1. Unlock the cable clampers to free the cable. metal. (See section 7.4.) 2. Disconnect the Speaker terminal. 2. Unlock the cable clampers to free the cable. 3.
7.9. Remove the SS-Board 3. Remove the Hanger metals (L, R) fastening screws (×2 each) and remove the Hanger metals (L, R). 1. Remove the Tuner unit. (See section 7.5.) 2. Unlock the cable clampers to free the cable. 3. Disconnect the connectors (SS3, SS11 and SS23). 4.
7.13. Remove the Plasma panel sec- 7.14. Remove the Glass holders tion from the Cabinet assy 1. Remove the Cabinet assy. (See section 7.13.) 2. Remove the screws (×4 (glass) 3. Remove the Glass holder side (L, R). 1. Remove the cabinet assy and the plasma panel fastening 4.
7.16. Replace the plasma panel Caution: A new plasma panel itself without Hanger metals is fragile. To avoid the damage to new plasma panel, carry a new plasma panel taking hold of the Hanger metals after assembling the Hanger metals and the Stand brackets. 1.
8 Measurements and Adjustments 8.1. Adjustment 8.1.1. Vsus selection Caution: When Plasma panel or A-board is replaced, Vsus should be set to LOW or HIGH. Procedure 1. Go into main item [VSUS] in Service Mode. LOW or HIGH will be displayed. 2.
Page 28
8.1.2. Sub-Contrast adjustment Name of measuring instrument Connection Remarks RF generator Base Band signal generator HD signal generator Steps Remarks Adjustment of TV (RF system) Note: Sub-contrast adjustment is unadjusted 1. Receive a RF PAL 100% Full White or Split Colour bar shown as below. for AV/ HD input.
Page 29
Steps Remarks Another procedure Adjustment of AV system 1. PAL 100% Full White or Split Colour bar receive AV1(or AV2), shown as below. 2. Goes into service mode. 3. Push [ 1 ] or [ 2 ] key, and goes into adjustment mode for [ Contrast ]. Adjustment 1.
Page 30
8.1.3. White balance adjustment Name of measuring instrument Connection Remarks W/ B pattern Panel surface Color analyzer (Minolta CA-100 or equivalent) Steps Remarks • Make sure the front panel to be used on the final set is fitted. Picture menu : Dynamic •...
9.3. Block (2/4) Diagram DIGITAL SIGNAL PROCESSOR IC9300 VIDEO DATA PLASMA AI VIDEO DATA LVDS DATA CPG with SS H/V Sync Control VIDEO DATA Sub Filed Processor P+3.3V IC9304 P3V_ P+3.3V ADDR/DATA FLASH IIC2 FLASH I/F MEMORY CONTROL DATA P_S0 P_S0 P_S1 DISCHARGE CONTROL...
10 Wiring Connection Diagram 10.1. Caution statement. Caution: Please confirm that all flexible cables are assembled correctly. Also make sure that they are locked in the connectors. Verify by giving the flexible cables a very slight pull. 10.2. Wiring (1)
12.2. K-Board K-BOARD (FOIL SIDE) TXN/K1LLUM T P 5 0 8 T P 5 0 1 TP2502 TP2501 T P 5 0 2 TP2508 TP2506 TP2504 T P 5 0 4 T P 5 0 3 RM2510 R M 5 1 0 T P 5 0 6 TP2503 TP2505...
12.4. C1-Board C1-BOARD (FOIL SIDE) TXNC11LLUM CMM11 1 C1 TNPA5075 S E E R E V E R S E F O R O R D E R N O . P b F C1-BOARD (COMPONENT SIDE) TXNC11LLUM C 1 2 0 C 1 1 5 R 1 3 1 I C 1 0 1...
12.5. C2-Board C2-BOARD (FOIL SIDE) TXNC21LLUM CMM21 T N P A 5 0 7 6 1 S E E R E V E R S E F O R O R D E R N O . P b F 1 2 3 C2-BOARD (COMPONENT SIDE) TXNC21LLUM...
12.6. SN-Board SN-BOARD (FOIL SIDE) TXNSN1LLUM S N M M 1 CRNo.14 S N M M 2 T P 1 2 2 T P 7 9 L 8 5 1 T P 1 2 1 Q 6 2 1 Q 4 2 1 D 4 2 1 Q 6 0 1 D 6 4 2...
Page 81
SN-BOARD (COMPONENT SIDE) TXNSN1LLUM A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8 A 4 8...
12.7. SS-Board SS-BOARD (FOIL SIDE) TXNSS1LLUM C 2 4 1 C 1 9 3 L 0 1 4 L 0 1 3 L 0 1 2 L 3 0 3 L 0 1 1 C R N o . 1 6 L 1 0 3 T P 6 6 T N P A 5 0 7 2...
Page 83
SS-BOARD (COMPONENT SIDE) TXNSS1LLUM C 2 4 4 R 1 3 1 R 1 3 5 C 1 0 6 C 1 0 5 R 1 3 6 C 2 4 2 R 1 9 1 C 1 0 4 D 1 3 1 C 1 0 3 C 3 2 8...
Page 89
13.1.5. Mechanical Replacement Parts List...
Page 90
Ref. Safety Part No. Part Name & Description Q'ty Remarks K2AHYH000033 AC INLET WITH CABLE 1 PAVCSG K2CT3YY00021 AC CORD 1 PAVCSG K/P/V K2CT3YY00022 AC CORD 1 PAVCSG P MD42H13A2J PLASMA DISPLAY PANEL N2QAYB000370 REMOTE CONTROL TBL3EX0007 PEDESTAL STAND 1 PAVCSG TBLA3679 STAND POLE R TBLA3680...
Page 91
Ref. Safety Part No. Part Name & Description Q'ty Remarks TPE3EP002 BAG FOR AC CORD 1 PAVCSG TPE3EP003 ACCESSORIES BAG 1 PAVCSG TPEB340 BAG (STAND ACCESSORY) TPEH418 SET BAG 1 PAVCSG TQB3EC0013 INSTRUCTION BOOK(ENGLISH) 1 PAVCSG TQB3EC0014 INSTRUCTION BOOK(ARABIC) 1 PAVCSG M/P TQB3EC0017 INSTRUCTION BOOK(CHINESE) 1 PAVCSG K/V...
13.2. Electrical Replacement Parts List 13.2.1. Replacement Parts List Notes...
Page 93
13.2.2. Electrical Replacement Parts List Safety Ref. No. Part No. Part Name & Pcs Remarks Description Safety Ref. No. Part No. Part Name & Pcs Remarks C2204 F1J1E105A231 C 1 UF 25V Description C2205 F1J1A106A087 C 0.010UF, K, TZTNP01LLUM CIRCUIT BOARD A (RTL) C2206 F1H0J475A041 C 4.7UF, K, 16V...
Page 94
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description C2275 F1J1E105A231 C 1 UF 25V C4749 F1G1H102A730 C 1000UF, 50V C2277 F1H1C105A145 C 0.01UF, K, 16V C4750 F1G1C104A116 C 0.10UF, K, 16V C2279 F1G1C104A116 C 0.10UF, K, 16V...
Page 95
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description C8002 ECJ1VB0J105K C 1UF, K, 6.3V C8074 F1G1H102A730 C 1000UF, 50V C8003 F1G1C104A116 C 0.10UF, K, 16V C8075 F1G1C104A116 C 0.10UF, K, 16V C8004 F1G1C104A116 C 0.10UF, K, 16V...
Page 96
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description C8517 F1J1A106A087 C 0.010UF, K, C9371 F1J1A106A087 C 0.010UF, K, C8519 F1G1A105A047 C 1UF, K, 10V C9372 F1J1A106A087 C 0.010UF, K, C8520 F1G1C104A116 C 0.10UF, K, 16V C9373...
Page 97
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description C14984 F1L2E224A028 E 2200UF, 25V C16581 F1K1E105A029 C 1UF, Z, 25V C14987 F1H1H104A970 C 0.1UF, K, 50V C16582 F1K1E475A134 C 4.7UF, Z, 25V C14988 F1H1H104A970 C 0.1UF, K, 50V...
Page 98
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description K1MY55B00001 55P CONNECTOR D16411 B0ACCJ000048 DIODE K1MY55B00001 55P CONNECTOR D16421 B0FACP000006 DIODE K1MY55B00001 55P CONNECTOR D16441 B0ECHR000001 DIODE K1MY55B00001 55P CONNECTOR D16451 B0ECHR000001 DIODE...
Page 99
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description IC2106 C1AB00003069 IC JK4501 K1FY119D0011 CONNECTOR PAVCSG IC2108 C1AB00003240 IC PAVCSG JK4502 K1FY119E0015 CONNECTOR PAVCSG IC2109 C1AB00002428 IC PAVCSG JK8502 K1NA12E00017 12P CONNECTOR...
Page 100
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description L9800 G1C6R8Z00010 INDUCTION COIL Q8312 B1CBHD000002 FET L9801 G1C100MA0416 INDUCTION COIL Q8313 B1CBHD000002 FET L16011 G0ZZ00002183 PEAKING COIL Q9000 B1ABCF000231 TRANSISTOR L16012...
Page 101
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R2119 D0GA470JA015 M 47 OHM, R2290 D0GA153JA015 M 15K OHM J J,0.063W 0.063W R2122 ERJ2GEJ221 M 220 OHM, R2299 D1BB75R0A055 M 75 OHM, 1/10W J,0.063W...
Page 102
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R2515 D0GB473JA057 M 47KOHM,J,1/10W R4739 D0GA473JA015 M 47 OHM, J,0.063W R2516 D1BB6800A055 M 680 OHM, 1/10W R4740 D0GA473JA015 M 47 OHM, R2517 ERJ3GEYJ223 M 22KOHM,J,1/16W...
Page 103
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R5673 D0GA473JA015 M 47 OHM, R8056 D0GA152JA015 M 1.5KOHM, J,0.063W J,0.063W R5674 D0GA222JA015 M 2.2KOHM, R8057 D0GA152JA015 M 1.5KOHM, J,0.063W J,0.063W R5675...
Page 104
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R8332 ERJ2GEJ220 M 22 OHM, R9072 ERJ2GEJ103 M 10KOHM, J,0.063W J,0.063W R8336 ERJ2GEJ220 M 22 OHM, R9100 D0GA473JA015 M 47 OHM, J,0.063W J,0.063W R8337...
Page 105
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R9213 D0GA470JA015 M 47 OHM, R9998 D1BA1601A014 M1.60KOHM, 1/10W PAVCSG J,0.063W R9999 D0GA472JA015 M 4.7KOHM, R9215 ERJ2GEJ104 M 100KOHM, J,0.063W J,0.063W R14349...
Page 106
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R16191 ERJ6GEYJ151V M 150 OHM,J,1/ R16506 ERJT06J100V M 10 OHM,F,0.25W R16510 ERJT14J1R0U C1.0 OHM, J,1/4W R16192 D0GB103JA057 M 10K OHM J 1/ R16512 D0GB473JA057 M 47KOHM,J,1/10W R16517...
Page 107
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R16679 D1BB1002A087 M 10KOHM, 1/10W R16843 ERJ6GEYJ102V M 1K OHM J 1/10W R16680 D1BB1002A087 M 10KOHM, 1/10W R16844 ERA6YEB242 M 24KOHM, 1/10W R16681...
Page 108
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R17217 EXB38V681J RESISTOR ARRAY C113 F1J1E225A209 C 2.2 UF 25V R17218 EXB38V470J RESISTOR ARRAY C114 F1H1C224A065 C 0.22UF, K, 50V R17219 ERJ6GEY0R00V M 0 OHM J 1/10W C115...
Page 109
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description C724 ECJ1VB1H103K C 0.001UF, K, F100 K5E802BZ0002 FUSE C725 ECJ1VB1H103K C 0.001UF, K, F101 K5E802BZ0002 FUSE F200 K5G631B00008 FUSE C726 F1J1H333A571 C 0.033UF, 50V C727...
Page 110
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description Q901 B1CERP000025 FET R218 D0B1825JA033 M1.22MOHM,J,0.05 R300 D0GZ181JA020 M 180 OHM,J, R101 D0GB394JA057 M 390KOHM J 1/ 0.5W R301 D0GZ181JA020 M 180 OHM,J, R102...
Page 111
Safety Ref. No. Part No. Part Name & Pcs Remarks Safety Ref. No. Part No. Part Name & Pcs Remarks Description Description R627 D0GB103JA057 M 10K OHM J 1/ R746 ERJ6GEYJ103V M 10K OHM J 1/ R628 ERJ3GEYJ222 M 2.2KOHM,J,1/ R749 ERJ6GEY0R00V M 0 OHM J 1/10W R750...
Page 112
Safety Ref. No. Part No. Part Name & Pcs Remarks Description R908 ERJ6ENF3301 M 3.3KOHM, 1/10W R909 D0GB473JA057 M 47KOHM,J,1/10W R910 ERJ3GEYJ333 M 33KOHM,J,1/16W R911 ERJ3GEYD153V M 15KOHM,J,1/16W R912 ERJ6GEYJ331V M 330 OHM J 1/ R913 ERJ6RBD152 M 1.5KOHM,J,1/ R914 ERJ6GEYJ102V M 1K OHM J 1/10W R915 ERJ6GEY0R00V M 0 OHM J 1/10W...