Advertisement
Quick Links
(Moving) Clowns spinning dishes : Assembly Instructions
View of completed model
Assembly Instructions : Six A4 sheets (No. 1 to No. 6)
* Build the model by carefully reading the Assembly Instructions , in the parts sheet page order.
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Scissors, set square, glue(We recommend stick glue), pencil, used
Tools and materials
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
Assembly tip
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
Caution
so be sure to keep them out of the reach of young children.
*
This model changes appearance in a number of
ways when you move the lever beneath the model's
frame to the left and right : the eyes on the giant
clown face blink, open wide, and move in circles.
Glue
The glue spot(colored dot)
shows where to apply the glue.
Glue spot(Red dot)
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue spot(Blue dot)
Glue to the rear of the other part.
©
Canon Inc.
Before starting assembly : Writing the number of each section on its back side
before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out
the sections.)
Round bar : Use to give parts a curved surface.
Tweezers : Useful in working with fine parts.
Glue the entire reverse sides of part 1 and
part 4 to each other, as shown in this illustration.
Take care in positioning and direction of
the parts when gluing them.
Caution :
Spread the glue in a thin layer,
to prevent these parts from
warping after you glue them
together.
Glue part 2 to the remaining
uncovered area of part 4.
©
Hideharu Naitoh & F design
Indicates where sections should
be glued together.
Indicates where to insert sections.
Do not glue the sections together.
Cut along the line.
Use care here.
Glue the rear sides of part 2 and part 3
to each other, lining these parts up.
Advertisement
Related Manuals for Canon CREATIVE PARK (Moving) Clowns spinning dishes
Summary of Contents for Canon CREATIVE PARK (Moving) Clowns spinning dishes
- Page 1 (Moving) Clowns spinning dishes : Assembly Instructions © Canon Inc. © Hideharu Naitoh & F design Indicates where sections should Before starting assembly : Writing the number of each section on its back side be glued together. before cutting out the sections is highly recommended.
- Page 2 (Moving) Clowns spinning dishes : Assembly Instructions © Canon Inc. © Hideharu Naitoh & F design Parts 18 and 19 Build two identical parts.
- Page 3 (Moving) Clowns spinning dishes : Assembly Instructions © Canon Inc. © Hideharu Naitoh & F design Parts , and Glue the reverse sides of parts 20 and 24 together, by aligning the V-Shaped cutouts at either end. Caution : spread a thin layer of glue on the surface to ensure it does not warp after gluing these parts together.
- Page 4 (Moving) Clowns spinning dishes : Assembly Instructions © Canon Inc. © Hideharu Naitoh & F design Use a round bar to give a slight curve to the left and Parts right sides of the hat. Parts Parts...
- Page 5 (Moving) Clowns spinning dishes : Assembly Instructions © Canon Inc. © Hideharu Naitoh & F design Parts Build two identical parts, using these as the left and right sides of the frame. Parts Front corner Rear corner...
- Page 6 (Moving) Clowns spinning dishes : Assembly Instructions © Canon Inc. © Hideharu Naitoh & F design Place the model in a vertical position, against a wall or some other surface, to check its overall movement. Finished!