Related Manuals for Hitachi RM-LTX7000DY
Summary of Contents for Hitachi RM-LTX7000DY
- Page 1 INSTRUCTIONS HITACHI G-SWORD ROTARY SHAVER RM-LTX7000DY For household use only RM-LTX7000 交流/充電式兩用 AC/RECHARGEABLE 日本製造 Made in Japan...
- Page 4 〔 〕 （ ） 90°...
- Page 6 English Safety precautions Items described here are for using the product safely and properly, and to prevent hazards and injury to the user and other persons before they occur. Items are classified as follows. All items are important descriptions related to safety, therefore make sure to observe them.
- Page 7 Do not use the power adaptor and LED light dryer in a place where water is splashed, such as a bathroom, or in a place with high humidity. (Cause of electric shocks and short circuits) Prohibited Detach the hand-held part from the supply cord before cleaning it in water. Be sure to disconnect the power adaptor from the outlet and main body for maintenance.
-
Page 8: Safety Precautions
Never use any other power adaptor and LED light dryer than the ones included. Also, do not charge any other product with the included power adaptor. (Cause of fires by short circuits or abnormal heating) Do not remove the main body from the LED light dryer during drying. (Cause of burns by the light emitting lens or foil that becomes hot during drying) Prohibited Do not apply the trimming blade directly to ears and nose. -
Page 9: Preparation Before Use
Trimming knob : Slide this upward. Comb Guides long or rough beard into the foil. LED light dryer (Included in the RM-LTX7000DY) Charging connector Main body detection switch The dry switch cannot be turned on unless the main body is set properly. - Page 10 When the capacity of the battery is sufficient, the charging completion lamp may be turned off early. Charging by using an LED light dryer (Included in the RM-LTX7000DY) Connect the power adaptor to the LED light dryer and an outlet, and insert the main body socket into the charging connector of the LED light dryer.
-
Page 11: How To Use
How to use It is recommended to use the shaver at an ambient temperature of 5°C to 35°C. Use or storage at a temperature below the recommended temperature may disable the shaver or cause a reduced number of operating times. For initial use, trim while lightly applying the shaver to skin. - Page 12 Power mode Beard can be shaved strongly and quickly at the time of start or in response to a thick beard. (Fig.11) Mode indicator “lights.” Auto lamp “turns off.” The auto lamp is "turned off." The mode indicator "lights (blue)." Normal Mode Beard can be shaved comfortably and softly in response to normal beard and finishing.
-
Page 13: Maintenance
3. Turn "OFF" the switch and store the trimming blade after operation. (Fig.16) Caution Never place fingers on the upper side of the trimming knob. (The trimming blade will contact fingers at the time of storing.) If the trimming knob is pushed downward with the trimming blade contacting fingers, storage will be impossible due to the disconnected lever. - Page 14 “EMP” flashes, and then charge for approximately 45 minutes. This mark means suitable for cleaning under an open water tap. Drying with the LED light dryer (Included in the RM-LTX7000DY) The main body and trimming blade cannot be dried. Use at an ambient temperature of 15〜35 or more.
- Page 15 CAUTION Never use alcohol, benzine, and thinner, etc. (Causes of deformation and discoloration) Maintenance of the LED light dryer (Included in the RM-LTX7000DY) The LED light dryer cannot be washed with water. Caution Make sure to disconnect the power adapter from the LED light dryer.
-
Page 16: Troubleshooting
1. Turn "OFF" the switch to remove the cap and head holder. (Fig.17) Press the head holder removal button (1) to remove the head holder in the arrow (2) direction. 2. Detach the foil-cutter assembly. (Fig.28) Slide the foil-cutter assembly detaching knob to the right (1),pick up and pull both ends of the foil-cutter assembly straight upward (2) to detach it. -
Page 17: Specifications
Symptom Check point Remedy - Failure of drying with Check for accumulation of dust, Periodically perform maintenance. the LED light dryer etc., inside the LED light dryer. Check to see if water drops on Wipe off water drops on the main the main body and blade surface body and blade surface before setting. - Page 18 -13-...
- Page 19 -14-...
- Page 20 -15-...
- Page 21 -16-...
- Page 22 -17-...
- Page 23 -18-...
- Page 24 -19-...
- Page 25 -20-...
- Page 26 -21-...
- Page 27 -22-...
- Page 28 -23-...
- Page 29 -24-...