Table of Contents
Advertisement
Quick Links
CE Guard Kit
Groundsmaster
Model No. 30689
Note:
Determine the left and right sides of the machine from the normal operating position.
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger. Replace any decal that is damaged or missing.
144-7254
1. Read the Operator's Manual.
© 2021—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
360 Multi-Purpose Machine
decal144-7254b
Register at www.Toro.com.
Form No. 3444-746 Rev A
Installation Instructions
*3444-746*
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro Groundsmaster 30689
Summary of Contents for Toro Groundsmaster 30689
- Page 1 Replace any decal that is damaged or missing. decal144-7254b 144-7254 1. Read the Operator’s Manual. *3444-746* © 2021—The Toro® Company Original Instructions (EN) Register at www.Toro.com. 8111 Lyndale Avenue South Printed in the USA Bloomington, MN 55420...
- Page 2 decal144-7261 144-7261 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site.
-
Page 3: Table Of Contents
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Push nut (3/8 inch) Secure the storage compartment. Right shield Rear shield Install the shield(s). U-bolt Flange nut Locking latch Latch plate Bolt (3/8 x 1 inch) Install the hood locking latch. -
Page 4: Procedure
Securing the Storage Installing the Shield(s) Compartment Parts needed for this procedure: Right shield Parts needed for this procedure: Rear shield Push nut (3/8 inch) U-bolt Flange nut Procedure Park the machine on a level surface, lower the For Models Equipped with a cutting unit or attachment, engage the parking brake, and shut off the engine, and remove the Kubota Engine... -
Page 5: U-Bolt
For Models Equipped With a Yanmar Engine (Without a Cab) Loosely install a rear shield to the right rear frame tube with a U-bolt and 2 flange nuts (Figure Position the shield near the tube radius and contacting the frame plate. g026721 Figure 4 1. -
Page 6: Flange Head Bolt (3/8 X 1 Inch)
Securing the Floor Plate Parts needed for this procedure: Flange head bolt (3/8 x 1 inch) Push nut (3/8 inch) Retaining nut (3/8 inch) Procedure Raise the floor plate. Install a retaining nut at the frame hole under the right front corner of the floor plate (Figure g014581 Figure 5... -
Page 7: Flange Head Bolt (3/8 X 1 Inch)
Securing the Seat Plate Securing the Front Cover Parts needed for this procedure: Parts needed for this procedure: Flange head bolt (3/8 x 1 inch) Push nut Push nut (3/8 inch) Retaining nut (3/8 inch) Procedure Remove the 2 flange head bolts securing the Procedure front cover to the top of the front axle (Figure... -
Page 8: Flange Head Bolt (5/16 X 1-1/4 Inches)
Securing the Belt Covers Securing the Floor Plate Cab Models Only Parts needed for this procedure: Flange head bolt (5/16 x 1-1/4 inches) Parts needed for this procedure: Retaining nut (5/16 inch) Push nut Push nut Procedure Procedure Remove the 4 bolts securing the floor plate to Perform this procedure for the right and left side belt the frame (Figure... - Page 9 Securing the Firewall Cab Models Only Parts needed for this procedure: Push nut Procedure Remove the 4 bolts securing the firewall to the frame (Figure 11). g014587 Figure 11 1. Firewall 3. Push nut 2. Flange head bolt Install the flange head bolts into the firewall using push nuts (3/8 inch).
-
Page 10: Stability Decal (Part No. 144-7261)
Installing the Decal Parts needed for this procedure: Stability decal (Part No. 144-7261) Sound decal (Part No. 144-7254) Applying the Tipping Hazard Decal Portion Angle Decal Portion Table 18 degrees 19 degrees 20 degrees 21 degrees 22 degrees 23 degrees 2015 and After Model-Number Configuration Table Model 30481 Model 30353... - Page 11 g351697 Figure 12 1. Tipping hazard portion—stability decal (Part No. 138-8203) Dampen the area with water or mildly soapy water. Peel off the backing of the decal portion, apply it over the existing tipping-hazard warning as shown in Figure 12, and squeegee across the decal using overlapping strokes from the center toward the edges. Applying the Sound Power and CE Decal Portions Sound-Power Decal Portion Table 103 dBA...
- Page 12 Pre-2015 Model-Number Configuration Table (cont'd.) 31223 4WD Kubota 1505 Highlighted values (*) that show the standard configuration of the model. These numbers include an uncertainty value (k) of 1 dBA. Sound power level was determined according to procedures outlined in ISO 11094. Use the Sound-Power Decal Portion Table and the 2 model-number configuration tables to select the portion of the sound decal (144-7253) for your machine.