Toro Groundsmaster 3320 Installation Instructions Manual
15 cu. ft. hopper kit
Hide thumbs
Also See for Groundsmaster 3320:
- Service manual (508 pages) ,
- Operator's manual (52 pages) ,
- Operator's manual (28 pages)
Table of Contents
Advertisement
Quick Links
15 CU. FT. HOPPER Kit
Groundsmaster
Model No. 30356–250000001 and Up
Safety
Before Operating
• Read and understand the contents of this manual before
starting and operating the machine. Become familiar
with all controls and know how to stop quickly.
• Never allow children to operate the machine. Do not
allow adults to operate the machine without proper
instruction. Only trained operators, skilled in slope
operation and who have read this manual should operate
this machine.
• Never operate machine when under the influence of
drugs or alcohol.
• Remove all debris or other objects that might be picked
up and thrown by cutter blades. Keep all bystanders
away from the operating area.
• Keep all shields and safety devices in place. If a shield,
safety device, or decal is defective or damaged, repair
or replace it before operation is commenced. Also,
tighten any loose nuts, bolts, and screws to insure
machine is in safe operating condition.
• Do not wear loose–fitting clothing because it could get
caught in moving parts. Always wear long pants and
substantial shoes. Wearing safety glasses, safety shoes,
and a helmet is advisable and required by some local
ordinances and insurance regulations.
• Be sure interlock switches are adjusted correctly so
engine cannot be started unless traction pedal is
released–neutral position–and PTO switch is in
DISENGAGED position.
• Fill fuel tank before starting the engine. Avoid spilling
any fuel. Since fuel is flammable, handle it carefully.
– Use an approved fuel container.
– Do not fill fuel tank when engine is hot or running.
– Do not smoke while handling fuel.
– Fill fuel tank outdoors and only to the bottom of the
filler neck.
– Wipe up any spilled fuel.
W 2005 by The Toro Company
8111 Lyndale Avenue South
Bloomington, MN 55420-1196
)
3320 and 3380–D
While Operating
• Sit on the seat when starting the engine and operating
the machine.
• Before starting the engine:
– Engage parking brake.
– Make sure traction pedal is in neutral and PTO is in
DISENGAGE position.
– After engine is started, release parking brake and
keep foot off traction pedal. Machine must not
move. If movement is evident, the neutral return
mechanism is adjusted incorrectly. Shut engine off
and adjust until machine does not move when
traction pedal is released.
• Do not run the engine in a confined area without
adequate ventilation. Exhaust fumes are hazardous and
could possibly be deadly.
• Maximum seating capacity is one person. Therefore,
never carry passengers.
• Check carefully for overhead clearances before driving
under any objects.
• The grass deflector or complete blower assembly must
always be installed on cutting unit.
• To maintain machine control, 75 lb. of weight must be
mounted on left front wheel of traction unit before
using the 15 cu. ft. Hopper kit. Refer to traction Unit
Operator's Manual for additional weight requirements.
• Operator must be skilled and trained in how to drive on
hillsides. Failure to use caution on slopes or hills may
cause loss of control and vehicle to tip or roll possibly
resulting in personal injury or death.
• Traverse slopes carefully. Do not start or stop suddenly
when traversing slopes or when traveling uphill or
downhill.
• If engine stalls or machine loses headway and cannot
make it to the top of a slope, do not turn machine
around. Always back slowly straight down the slope.
• Using the machine demands the operator's complete
attention. To prevent loss of control:
– Operate only in daylight or when there is good
artificial light.
– Drive slowly.
1
Form No. 3353–222
Installation Instructions
All Rights Reserved
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro Groundsmaster 3320
Summary of Contents for Toro Groundsmaster 3320
- Page 1 – Wipe up any spilled fuel. – Operate only in daylight or when there is good artificial light. – Drive slowly. W 2005 by The Toro Company All Rights Reserved 8111 Lyndale Avenue South Printed in the USA Bloomington, MN 55420-1196...
- Page 2 • If major repairs are ever needed or assistance is desired, damage before restarting the engine and operating the contact an Authorized TORO Distributor. cutting unit. Assure cutting unit blades are in good condition and blade bolts are torqued to proper •...
-
Page 3: Safety And Instruction Decals
• If the engine must be running to perform maintenance of the machine, use genuine TORO replacement parts or an adjustment, keep clear of PTO shaft, cutting unit and accessories. Replacement parts and accessories blades, and other moving parts. made by other manufacturers may result in non–conformance with the safety standards, and the... -
Page 4: Loose Parts Chart
Set Up LOOSE PARTS CHART Note: Use this chart as a checklist to assure all parts necessary for assembly have been received. Without these parts, total set-up cannot be completed. Some parts may have already been assembled at factory. Description Qty. -
Page 5: Optional Equipment
Description Qty. Hydraulic Hoses Protective Sleeve Retaining Ring Retaining Ring Connect Hydraulic Lines Dust Plug Dust Cap Quick Disconnect (nipple & coupler) Hopper Assembly Welded Mounting Pin Hair Pin Cotter – for 1/2” Shaft Install Hopper Assembly Hair Pin Cotter – for 1/4” Shaft Carriage Bolt 5/16 –... - Page 6 Mount the Control Valve 1. Remove the seat and the seat base from the machine. 3.50 1.25 2. Loosen the fuel tank mounting fasteners so the fuel tank can be elevated enough to gain access to the right fender. 2.25 3.
- Page 7 7. Connect the steering hose (from the lift valve “P” port) 12. Remove the knock–out plug, under the decal, in the to the 90_ fitting on the operator side of the control lower control panel (Fig. 7). valve (Fig. 4). 8.
- Page 8 Mount the Hopper Frame Note: Remove the hairpin cotter and pin securing the right side of the ROPS to the pivot bracket. Re–install the pin from the left side of the pivot bracket and secure with the hairpin cotter. Figure 11 1.
- Page 9 7. From the rear of the machine, slide the front of the 3. Slide the loop end of the dust cap (Fig. 15) over the end hopper frame onto the side mounting bracket pins and of the hydraulic hose coming from the rear valve fitting. the rear of the frame over the rear bracket pin.
- Page 10 Install Front Blowout Shields 4. Secure the harness to stationary frame components with cable ties. Note: The following instructions are as viewed from the front of the machine. Mount Hopper Assembly When hopper is used with a 52” Deck 1. Remove the tie straps securing the tie rods to the hopper arms.
- Page 11 Note: If there is excess thread protruding from the nuts or inside of wheel, cut it off with a hacksaw. The threaded rod must not contact any parts of the machine when the wheel is rotating. Important Refer to the weight chart in the Traction Unit Operator’s Manual for additional weight requirements.
-
Page 12: Hopper Operation
Operation Caution Note: Determine the left and right sides of the machine Use care to avoid a collision between the from the normal operating position. hopper and any stationary objects. Always trim with the left side of the cutting unit. Before Operating Hopper 1. - Page 13 Hopper & Frame Removal 1. Stop the unit, disengage the PTO, set the brake and shut off the ignition. 2. Move the hopper control valve lever forward and reverse a few times to release the pressure in the hydraulic system. 3.
-
Page 14: Maintenance
Maintenance Lubrication After every 25 hours of operation, grease the cylinder and all pivot points with No. 2 multi–purpose lithium base Adjusting the Rear Cover Latch grease. There are (8) grease fittings at various pivot points and (1) fitting on each end of cylinder (Fig. 23). 1. - Page 16 If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.