Table of Contents
Advertisement
Power Clear 621 QZR/QZE Snowthrower
Model No. 38458—Serial No. 312000001 and Up
Model No. 38459—Serial No. 312000001 and Up
Introduction
This machine is intended to be used by residential
homeowners. It is designed for removing snow from
paved surfaces, such as driveways and sidewalks,
and other surfaces for traffic on residential or
commercial properties. It is not designed for
removing materials other than snow, nor is it
designed for clearing off gravel surfaces.
Read this information carefully to learn how to operate
and maintain your machine properly and to avoid injury
and machine damage. You are responsible for operating
the machine properly and safely.
You may contact Toro directly at www.Toro.com for
machine and accessory information, help finding a
dealer, or to register your machine.
Whenever you need service, genuine Toro parts, or
additional information, contact an Authorized Service
Dealer or Toro Customer Service and have the model
and serial numbers of your machine ready. Figure 1
identifies the location of the model and serial numbers
on the machine. Write the numbers in the space
provided.
Figure 1
1. Model and serial number location
Purchased 2/1/14 Russopower.com
38459
Model No.
314001381
Serial No.
© 2011—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
This manual identifies potential hazards and has
safety messages identified by the safety alert symbol
(Figure 2), which signals a hazard that may cause serious
injury or death if you do not follow the recommended
precautions.
1. Safety alert symbol
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
Safety
Read and understand the contents of this manual
before you start the engine.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all
safety messages that follow this symbol to avoid
possible injury or death.
Improperly using or maintaining this machine
could result in injury or death. To reduce this
potential, comply with the following safety
instructions.
This machine is capable of amputating hands and
feet and of throwing objects. Failure to observe the
following safety instructions could result in serious
injury.
Training
• Read, understand, and follow all instructions on the
machine and in the manual(s) before operating this
machine. Be thoroughly familiar with the controls
and the proper use of the machine. Know how to
stop the machine and disengage the controls quickly.
Register at www.Toro.com.
Form No. 3369-499 Rev A
Operator's Manual
Figure 2
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Advertisement
Table of Contents
Related Manuals for Toro Power Clear 621QZE
Summary of Contents for Toro Power Clear 621QZE
- Page 1 Whenever you need service, genuine Toro parts, or Safety additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your machine ready. Figure 1 Read and understand the contents of this manual identifies the location of the model and serial numbers before you start the engine.
- Page 2 • Never allow children to operate the machine. Never repair to protect eyes from foreign objects that may allow adults to operate the machine without proper be thrown from the machine. instruction. • Keep the area of operation clear of all persons, Operation particularly small children.
-
Page 3: Clearing A Clogged Discharge Chute
Toro Snowthrower Safety The following list contains safety information specific to Toro products or other safety information that you must know. • Rotating rotor blades can injure fingers or hands. Stay behind the handles and away from the... -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Important: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 94-2577 1. To engage the rotor blades, hold the control bar against the handle. 2. To disengage the rotor blades, release the control bar. 117-9102 (Model 38458 only) Order part no. -
Page 5: Loose Parts
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Unfold the handle. Screws Install the discharge chute. Chute assembly Unfolding the Handle No Parts Required Figure 5 Procedure 1. -
Page 6: Installing The Discharge Chute
Note: The bottle of oil may contain an ounce or two more than the engine requires. Do not overfill the engine. Max fill: 20 oz. (0.6 l), type: automotive detergent oil Installing the Discharge Chute with an API service classification of SJ, SL, or higher. Use Figure 8 below to select the best oil viscosity for the Parts needed for this procedure: outdoor temperature range expected:... -
Page 7: Product Overview
Operation Note: Determine the left and right sides of the machine from the normal operating position. Adjusting the Control Cable DANGER No Parts Required Gasoline is extremely flammable and explosive. A fire or explosion from gasoline can burn you and others. -
Page 8: Checking The Engine Oil Level
starting, poor engine performance, and may cause 2. Pull out the choke lever (Figure 14 and Figure 15). internal engine damage. Note: For best results, purchase only the quantity of gasoline that you expect to use in 30 days. Otherwise, you may add fuel stabilizer to newly purchased gasoline to keep it fresh for up to 6 months. - Page 9 (model 38459 only) (Figure 17), or pull the recoil attempts, take the machine to an Authorized start handle (Figure 18). Service Dealer for service (model 38459 only). Note: If you pull the recoil handle and feel no resistance, the starter may be frozen. Thaw out the starter before attempting to start the machine.
-
Page 10: Stopping The Engine
Disengaging the Rotor Blades To disengage the rotor blades, release the control bar (Figure 20). Figure 20 Stopping the Engine To stop the engine, turn the ignition key Figure 22 counterclockwise to the Off position (Figure 21). To raise or lower the angle of the chute deflector, press the trigger on the chute deflector and move the chute deflector up or down (Figure 23). -
Page 11: Operating Tips
Clearing a Clogged Discharge only) to prevent the recoil starter and/or the electric starter from freezing up. Chute • In snowy and cold conditions, some controls and Important: Hand contact with the rotating moving parts may freeze. Do not use excessive force rotor blades inside the discharge chute is the when trying to operate frozen controls. -
Page 12: Recommended Maintenance Schedule(S)
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Check the control cable and adjust it if necessary. After the first hour • Check for loose fasteners and tighten them if necessary. •... -
Page 13: Changing The Engine Oil
1/8-inch (2 mm to 3 mm) gap between the control bar and the handle (Figure 25). Note: Moving the Z-fitting higher decreases the gap between the control bar and the handle; moving it lower increases the gap. 3. Hook the spring to the adjuster link and slide the spring cover over the adjuster link. -
Page 14: Servicing The Spark Plug
Figure 30 1. Oil fill cap Figure 32 7. Unscrew the oil fill cap and remove it (Figure 30). 9. Screw the oil fill cap into the oil fill hole, and hand 8. With the machine in the operating position, carefully tighten it securely. - Page 15 4. Remove the 4 screws that secure the shroud (Figure 34). Figure 35 1. Center electrode insulator 3. Air gap (not to scale) 2. Side electrode 12. Install the spark plug and torque it to 20–22 ft-lb (27–30 N-m). 13. Connect the wire to the spark plug. Note: Ensure that the breather tube is routed above the spark plug wire as shown in Figure 36.
-
Page 16: Replacing The Drive Belt
Replacing the Drive Belt the loose rotor pulley positioned just above the rotor shaft (Figure 37). If drive belt becomes worn, oil-soaked, excessively 6. Install the rotor pulley onto the rotor shaft cracked, frayed, or otherwise damaged, replace the belt. (Figure 37). - Page 17 Figure 40 1. Cable clamps 2. Position the Quick Shoot control between the two arrows located on the right hand side of the upper handle (Figure 41). Figure 42 4. Hold the discharge chute in the straight-ahead position, pull the lower cable casing downward until you remove the slack in the cable, and tighten the screw on the lower cable clamp securely (Figure 43).
- Page 18 7. Dispose of unused fuel properly. Recycle it according to local codes, or use it in your automobile. 8. While the engine is still warm, change the engine oil. Refer to Changing the Engine Oil. 9. Remove the spark plug. 10.
- Page 19 Air Induction System Where a warrantable condition exists, The Toro Company and its affiliate, — Air cleaner Toro Warranty Company, promise to repair your engine at no cost to you, including diagnosis, parts, and labor. — Intake manifold — Controlled hot air intake system Manufacturer’s Warranty Coverage...
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor’s service or have difficulty obtaining guarantee information, contact the Toro importer.