Table of Contents
Related Manuals for Sharp HP-TW10
Summary of Contents for Sharp HP-TW10
- Page 1 ENGLISH MODEL HP-TW10 TRUE WIRELESS STEREO EARPHONES OPERATION MANUAL Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product.
-
Page 2: Page Accessories
Accessories The following accessories are included. Stereo earbuds x 1 pair Charging case x 1 Eartips x 3 pairs USB charging cable x 1... -
Page 3: Table Of Contents
Contents Page Page Charging operation Accessories ........1 Charging the earbuds ...... 14 Contents ......... 2 Charging the charging case..... 14 Special notes ........ 3 Battery charging ......17 Getting started ........3 Troubleshooting ......18 Precautions ........6 Factory reset........20 Overview Specification Getting started ........ -
Page 4: Special Notes
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth ® SIG, Inc. and any use of such marks by SHARP is under license. Other trademarks and trade names are those of their respective owners. Getting started „... - Page 5 (Product with embedded battery ONLY). ● In case this product contains a battery incorporated within the product which cannot be readily removed by end users, SHARP recommends that only qualified professionals remove the battery, either for replacement or for recycling at the end of this product’s working life. To prevent damage to...
- Page 6 Special Notes (continued) Avoiding hearing damage If volume on the earphones is too high, permanent hearing loss may occur. Please set the volume to a safe level. You can become habitual to hear at high volume that may sound normal but can damage your ears. If you experience ringing in your ears or muffled speech, stop listening and have your ears checked by the specialist doctor.
-
Page 7: Precautions
● This unit should only be used within the range of 0°C - 40°C (32°F - 104°F). ● The apparatus is designed for use in moderate climates. ● SHARP is not responsible for damage due to improper use. Refer all servicing to a SHARP authorized service center. - Page 8 Precautions (continued) ● Use this product only with an agency approved power supply which meets local regulatory requirements (e.g., UL, CSA, VDE, CCC). ● The product rating is located at the bottom of the product. CAUTION: Risk of explosion if the battery is replaced by an incorrect type ●...
-
Page 9: Overview
Overview Thank you for choosing our product. Our HP-TW10 TRUE WIRELESS STEREO EARPHONES are designed with fashionable looks, powerful features and high compatibility, providing you with hands-free convenience in making calls and listening to music. Best choice for office using, traveling and driving. -
Page 10: Product Features And Functions
Product features and functions ● Integrated Bluetooth earbuds to meet various needs such as music listening and phone answering. ● With True Wireless Stereo technology, left and right earbuds are wirelessly connected. ● Stereo sound effect to enjoy perfect music. ●... -
Page 11: General Control
The earbuds will automatically power bluetooth device and search for “HP- off if there is no bluetooth connection TW10 SHARP” between the bluetooth source device ● If the earbuds are not turned on, and the earbuds for more than 5 touch and hold both L and R MFB minutes. -
Page 12: Bluetooth Connection
2 seconds to power on and it will auto reconnect to the bluetooth enabled device that was last connected. If there is no paired record, it will automatically enter pairing mode after power on. Turn on your Bluetooth device and search for “HP-TW10 SHARP” E-11... -
Page 13: Music Mode
Music mode Touch and hold R MFB Touch R MFB pad once pad for about 2 seconds to increase the volume. to skip up to next song. Touch and hold L MFB pad Touch L MFB pad once to for about 2 seconds to skip decrease the volume. -
Page 14: Phone Call Mode
Phone call mode Touch L or R MFB Touch L or R MFB pad twice to answer pad twice to end a a call. call. Touch and hold L or R MFB pad for about 2 seconds to reject an incoming call. While answering a call, to switch the call from the earbuds to mobile phone or vice versa, touch and hold L or R MFB pad for about 2 seconds. -
Page 15: Charging Operation
Charging operation Charging the earbuds „ Put the earbuds into the charging case. Earbuds red LED lights up indicate under charging. Earbuds red LED turns off indicate fully charged. Charging: Red LED light up Fully charged: Red LED light off Charging the charging case „... - Page 16 Charging operation (continued) Charging via USB cable : Insert the USB cable (provided) to the USB terminal located at the rear of the charging case as shown. Wireless charging : Place the charging case on the surface of a wireless charger with direction as shown.
- Page 17 Charging operation (continued) 0-25% 1st white LED blinking. 25-50% 1st LED lights up, 2nd LED blinking. 50-75% 1st and 2nd LED light up, 3rd LED blinking. 75-99% 1st, 2nd and 3rd LED light up, 4th LED blinking. 100% fully charged, four LEDs light up permanently. Notes : ●...
-
Page 18: Battery Charging
Charging operation (continued) Battery charging „ The earbuds use embedded rechargeable battery that cannot be removed. Do not attempt to remove the battery from the earbud or the charging case. Otherwise, the earbud or charging case may be damaged. If the earbud is not used in a long time, keep it in a cool and well ventilated place. Charge the earbuds every months. -
Page 19: Troubleshooting
Troubleshooting Problem Cause Solution Description The earbuds The earbud is out of power. Put the earbuds into the cannot be charging case. If the charging powered on case is also out of power, charge the case with an adapter first. The MFB button is not pressed Press and hold the MFB button and held for sufficient time. - Page 20 Troubleshooting (continued) Problem Cause Solution Description The earbuds cannot be powered off. The earbud program is in error Reset the earbuds. Refer to There is due to an incorrect operation. “Factory reset” on page 20. no interlink between L and R earbuds.
-
Page 21: Factory Reset
Troubleshooting (continued) Factory reset „ During power off, touch and hold both L and R MFB pad simultaneously for about 10 seconds. (The earbud will power on and off back again) Touch and hold the MFB pad for about 2 seconds to power on. A “Tone”... -
Page 22: Specification
Specification As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual unit. -
Page 23: Bluetooth
Specification (continued) Bluetooth „ Version V 5.0 (HSP / HFP / A2DP / AVRCP) Maximum < 20 dbm power transmitted Frequency 2.402 GHz - bands 2.480 GHz E-22... - Page 24 Printed in China 21E R MW 1 92L5350010491B...