Advertisement
Available languages
Available languages
Quick Links
MULCH KIT STAMPED 42" DECK
Model No. 19A70041791
Model 19A70041791 mulch kit is designed for use with select 42-inch two-blade
cutting decks. Refer to your tractor's Operator's Manual to assure compatibility.
Carton Contents
Before beginning installation, remove all parts from the carton to make sure
everything is present. Carton contents are listed below and shown in Figure 1. Part
numbers are listed in parentheses.
•
Two Mulching Blades (742-0616A)
•
One Deck Mulch Plug Assembly (631-05195A)
•
One Wing Knob (720-04122)
•
One Flat Washer (736-0159)
•
One Mulch Plug Wire (747-06686)
Figure 1
Blade Installation
Before beginning installation, place the tractor on a firm and level surface, set the
parking brake, place the PTO in the disengaged (OFF) position, stop the tractor's
motor and remove the ignition key to prevent unintended starting.
Cutting blades are sharp. Always protect hands by wearing heavy leather work
gloves to grasp blades.
1.
Remove the cutting deck from beneath the tractor as instructed in your
tractor's Operator's Manual.
2.
Gently flip the deck over to expose its underside.
3.
Stabilize one of the cutting blades with a blade lock tool or a block of wood.
See Figure 2.
INSTALLATION MANUAL
WARNING
WARNING
Figure 2
Form No. 769-19050
(November 12, 2018)
Advertisement
Related Manuals for Craftsman 19A70041791
Summary of Contents for Craftsman 19A70041791
- Page 1 MULCH KIT STAMPED 42” DECK INSTALLATION MANUAL Model No. 19A70041791 Model 19A70041791 mulch kit is designed for use with select 42-inch two-blade Blade Installation cutting decks. Refer to your tractor’s Operator’s Manual to assure compatibility. Carton Contents WARNING Before beginning installation, place the tractor on a firm and level surface, set the Before beginning installation, remove all parts from the carton to make sure parking brake, place the PTO in the disengaged (OFF) position, stop the tractor’s...
- Page 2 Remove the hex flange nut that secures the blade to the spindle. To install the mulch plug, pivot the discharge chute upward. Refer to Figure 5: IMPORTANT: The hex flange nuts have a right-handed (normal) thread pattern. Insert the mulch plug rod into the hole found on the bracket (or deck Do NOT attempt to force the nuts in the opposite direction.
- Page 3 See the inset in Figure 6. Figure 5 Figure 6 IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US. CRAFTSMAN® is a registered trademark of Stanley Black & Decker, Inc., used under license. © 2018 CRAFTSMAN U.S. & Canada Only CRAFTSMAN.com 1-888-331-4569 WWW.CRAFTSMAN.COM...
- Page 4 otes...
-
Page 5: Manual De Instalación
Modelo N.º 19A70041791 Instalación de la cuchilla El kit de abono del modelo 19A70041791 está diseñado para ser utilizado con plataformas de corte de dos cuchillas seleccionadas de 42 pulgadas. Consulte el manual del operador del tractor para asegurar la compatibilidad. - Page 6 IMPORTANTE: Las tuercas hexagonales con brida tienen un patrón de rosca arriba. Consulte la Figura 4: (normal) hacia la derecha. NO intente forzar las tuercas en la dirección opuesta. Inserte la varilla del adaptador para abono en el orificio que se Hacerlo dañará...
- Page 7 Deslice el cable del adaptador para abono (747-06686) sobre el pasador que Figura 6 SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS. CRAFTSMAN® es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencia. © 2018 CRAFTSMAN, se aplica solo en EE. UU. y Canadá CRAFTSMAN.com 1-888-331-4569 WWW.CRAFTSMAN.COM...
- Page 8 otes...
-
Page 9: Manuel D'installation
DE COUPE ÉTAMPÉ DE 42 PO (1,07 M) Numéro de modèle 19A70041791 L'ensemble de déchiquetage, modèle 19A70041791, est conçu pour être utilisé avec Installation de la lame certains plateaux de coupe à deux lames de 42 po (1,07 m). Reportez-vous au manuel de l'utilisateur du tracteur pour vous assurer de la compatibilité. - Page 10 IMPORTANT : Le contre-écrou à embase a un motif de fil droit (normal). d’évacuation vers le haut. Consultez la Figure 4. N'essayez PAS de forcer les écrous dans la direction opposée. Cela pourrait Insérez la tige du couvercle de déchiqueteuse dans l'orifice situé sur endommager les écrous.
- Page 11 Figure 5 Figure 6 COMMUNIQUEZ AVEC NOUS POUR TOUTE CRAFTSMAN® est une marque de commerce enregistrée de Stanley Black & Decker, Inc., elle est utilisée en vertu d'une licence. © 2018 CRAFTSMAN É.-U. et Canada uniquement QUESTION OU TOUT COMMENTAIRE.
- Page 12 CRAFTSMAN® is a registered trademark of Stanley Black & Decker, Inc., used under license. CRAFTSMAN® es una marca registrada de Stanley Black & Decker, Inc., utilizada bajo licencia. CRAFTSMAN® est une marque déposée de Stanley Black & Decker, Inc., utilisée sous licence.