Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
The SSP201 is the Full Face Mask and Belt assembly only, which must be used in conjunction with coalescing filter SSP21X and low
toxic breathing hose SSP20H to provide clean air. The SSP201K is the complete air-fed full face mask system (see parts list). All further
Refer to
Instructions
1.
SAFETY
1.1.
General
The SSP201K Complete Air Kit system is NOT designed for use in atmospheres containing flammable gas mixtures.
The SSP201K is designed for use against contaminants which are NOT immediately dangerous to life and health or where
self-contained breathing apparatus is not essential.
SSP201K is designed for use with COMPRESSED AIR ONLY. DO NOT USE WITH COMPRESSED OXYGEN OR OXYGEN
ENRICHED AIR.
No protection is given unless the mask is correctly fitted and an adequate supply of breathing air is maintained.
Only when the equipment is correctly worn, will it provide the prescribed degree of protection.
The SSP201K is the correct apparatus for persons with a beard or facial hair. DO NOT use a half mask.
A combination of wall mounted filter SSP21X and belt mounted carbon filter unit WILL NOT remove Carbon Monoxide, Carbon
Dioxide, or other toxic gases. Wall mounted filter SSP21X is designed to remove particulate and moisture from the air supply.
If you are in any doubt as to the suitability of the equipment for the work to be undertaken, consult your supplier.
1.2.
Negative Pressure
At high work rates air pressure within the mask may become negative (a vacuum) briefly as the user breathes in.
The apparatus has a maximum flow of 232 ltr/min and MUST NOT be used where work rate will require a supply in excess of
232 ltr/min.
1.3.
Compressed Air Supply
The user MUST ensure that the air supply to the apparatus is within the limits recommended. The air supply should be dry to avoid the
risk of freezing in cold conditions.
If the air supply ceases, or is reduced significantly, withdraw from contaminated atmosphere immediately and check system for faults.
2.
INTRODUCTION
SSP201K
A full kit of equipment manufactured to provide a protection factor of APF40. Primarily for use in automotive spray shops but also suitable for use
in none critical dust and fume applications. Allows user to safely perform all the tasks of cutting, grinding and spraying. Includes complete head set
which has wide vision, is easily adjustable and has a built in audible alert for low airflow. Waist belt assembly with a fixed flow control and easy to
change carbon deodorizing element. Supplied with 10mtr low toxic hose with 1.5mtr leader hose and a complete set of couplings. Adheres to the
following standards EN14594 class 3A, EN166 and EN12021
SSP201
Air fed mask and belt filter for Model No. SSP201K. Light durable mask with specially shaped visor to reduce glare and reflection providing a wide
field of vision. Waist belt assembly with a fixed flow control and an easy to change carbon deodorizing element.
3.
SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SSP201K
Operating Pressure: . . . . . . . . . . . . . . . . 30-100psi (2-7bar)
Maximum Pressure: . . . . . . . . . . . . . . . . . . . . . 116psi (8bar)
Air Flow: . . . . . . . . . . . . . . . . . . .150-180ltr/min (5.4-6.4cfm)
Maximum Operating Temperature: . . . . . . . . . . . . . . . . 35°C
© Jack Sealey Limited
INSTRUCTIONS FOR:
COMPLETE AIR FED BREATHING SYSTEM
SSP201K, SSP201(Mask & Belt Only)
MODEL NO:
references relate to the SSP201K complete kit.
The SSP201K system comprises a lightweight mask connected via
a breathing hose to a pre-set regulator, with spare carbon filter,
mounted on a comfortable waist belt with quick release buckle. The
hose kit consists of a compressed air supply hose and couplings,
fitted with a "Y" piece which connects to the pre-set regulator. A 1.5
metre compressed air supply hose is provided for connection of a
spray gun. A wall-mounted coalescing filter is supplied in the kit.
SSP201 Comprises mask and waist belt only
UK Protection Factor: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Hose Diameter:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8mm
Main Hose Length: . . . . . . . . . . . . . . . . . . . . . . . . . . . .10mtr
Leader Hose Length: . . . . . . . . . . . . . . . . . . . . . . . . 1.5mthr
Original Language Version
SSP201K,SSP201 Issue: 1 - 09/01/15
Advertisement
Related Manuals for Sealey SSP201K
Summary of Contents for Sealey SSP201K
- Page 1 SPECIFICATION Model No: ......SSP201K Operating Pressure: ....30-100psi (2-7bar) UK Protection Factor: .
- Page 2 4.3. Air Supply Pressure: The SSP201K Kit is designed to operate with a compressed air supply pressure of 2-7bar (30-100psi), measured at the input to the supply hose. The mask requires a minimum supply of 150ltr/min (5.4cfm) and if used with a spray gun a minimum of 620ltr/min (21cfm) must be available at 6bar (90psi).
- Page 3 WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Sole UK Distributor, Sealey Group, www.sealey.co.uk 01284 757500 Kempson Way, Suffolk Business Park, Bury St. Edmunds, Suffolk, 01284 703534 sales@sealey.co.uk IP32 7AR Original Language Version SSP201K,SSP201 Issue: 1 - 09/01/15 © Jack Sealey Limited...