Advertisement
Quick Links
thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instruction
protection
manual
1. SaFety
1.1.
General SaFety
disconnect the drill from the battery unit before changing accessories, servicing or performing any maintenance.
9
maintain the drill and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
ensure the drill is switched off before installing the battery pack.
9
Keep the drill and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the drill e.g. ceilings, floors and enclosures may contain electrical items or water piping.
9
ensure battery pack is correctly inserted into the drill handle and latched in place before attempting to switch on drill.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Keep chuck direction switch in the locked position until the drill is required for use.
9
Keep children and unauthorised persons away from the working area.
9
Keep drill and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
9
Do not use the drill where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
Do not allow children to operate the drill.
8
Do not operate the drill if any parts are missing as this may cause failure and/or personal injury.
8
Do not hold unsecured work piece in your hand.
8
Do not leave the drill operating unattended.
8
Do not carry the drill with your finger on the power switch. Keep chuck direction switch in the locked position.
8
Do not use the drill for a task it is not designed to perform.
8
Do not operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Do not get the drill or battery charger wet or use in damp or wet locations.
8
2.
introDuction
i
Powerful, lightweight cordless rotary hammer drill. durable composite housing with soft grip for added comfort. SdS Plus chuck. Two drilling
functions, rotary and rotary with hammer. Built-in LED work light. Forward, reverse and trigger lock. Variable speed trigger for greater control.
Requires Model No's CP20VBP, CP20VBP2 or CP20VBP4 20V Battery and Model No. CP20VMC Mains Charger.
3.
SpeciFication
i
model no: ............................................................CP20VSDS
no load Speed: ...................................................... 900 RPm
Impact Rate: ......................................................... 0-5000bpm
Chuck size: .............................................................SdS Plus
noise Power ..................................................................96 dB
noise Pressure .............................................................85 dB
Vibration ................................................................. 8.64 m/s
Uncertainty ................................................................ 1.5 m/s
Consumables:
Battery: .............................20V 2Ah-4Ah Li-ion (not included)
2Ah Battery .......................................................... CP20VBP2
3Ah Battery ............................................................ CP20VBP
4Ah Battery .......................................................... CP20VBP4
mains charger ....................................................... CP20VMC
© Jack Sealey limited
20V SDS pluS rotary hammer Drill -
boDy only
model no:
Wear a
Wear ear
Wear protective
mask
protection
Original Language Version
cp20VSDS
gloves
2
2
Advertisement
Related Manuals for Sealey CP20VSDS
Summary of Contents for Sealey CP20VSDS
- Page 1 Sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 If you suspect that the brushes may be worn, have them replaced at an authorised service centre. 5.5. StoraGe 5.5.1. Store this tool carefully in a secure, dry place out of the reach of children. Original Language Version © Jack Sealey limited...
- Page 3 Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk business park, bury St edmunds, Suffolk. ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...