Page 1
Front Load Washing Machine Model: HNS1260TVE/ME FRONT LOAD WASHING MACHINE Service Manual Suited model: HNS1260TVE HNS1260TVEME Features 300mm diameter porthole, door may be open at a 180 degrees. Class-A energy-saving; Homocentric tubs with higher energy efficiency Multi-gear speed controller Unique gasket design featuring no residual water hidden inside...
Front Load Washing Machine Model: HNS1260TVE/ME PRODUCT INTRODUCTION It represents HNS series appearance with big window 180 opening window 1200rpm spin speed.S pin speed is adjustive from 400 to 1200 rpm,and alse exclude spin(indicate"0") it's controlled by computer. alse choose cold water.
Front Load Washing Machine Model: HNS1260TVE/ME FEATURES 300mm diameter porthole, door may be open at a 180 degrees. Facilitate view of wash process, facilit ate unloading and easy to use with large porthole. Multi-gear speed controller According to different costuming you can slect corresponding spin speed from 400 to 1400 rpm.
Front Load Washing Machine Model: HNS1260TVE/ME SPECIFICATION Proposal 2007 New Sensor Front load washing machines Brand position center upper frame of door / chromed sticker Model number serigraphy right top corner control panel On white: silver / On silver : black or dark grey...
Page 6
Front Load Washing Machine Model: HNS1260TVE/ME...
Front Load Washing Machine Model: HNS1260TVE/ME Matters Needing Attention 2. Hold the plug and not the electric cable .A separate earthed socket is required for the power supply. The washing machine must be when unplugging the washing machine. positioned so that the plug is accessible.
Page 8
Front Load Washing Machine Model: HNS1260TVE/ME Matters Needing Attention 9.The carpet must not obstruct the ventilation 8.The washing machine should not be install- openings in the base of the washing machine. ed outdoors or in a damp place. In the event of water leakage or splashes allow the machine to dry naturally.
Page 9
Front Load Washing Machine Model: HNS1260TVE/ME Matters Needing Attention 3. Do not place heavy, heating source or wet 4. Do not hot wash foam rubber or sponge-like materials. articles on the top of the washing machine. 5. Before washing, do up zippers, buttons and 6.
Front Load Washing Machine Model: HNS1260TVE/ME Installation Dismantle the packing bolts as shown in Fig. 2. The packing bolts are designed for clamping anti-vibration components inside of the washing machine during the transportation process. Beforeuse: 1. Remove the back plate;...
Page 11
Front Load Washing Machine Model: HNS1260TVE/ME Installation Joining the Inlet Hose to the Washing Machine Connect the nut on the inlet hose to the connector on the water valve. Connect of water inlet valve The height of the drainage outlet must be 80-100cm. To prevent the drainage hose from dropping off, fix it to the drainage hose clip at the back of the washing machine.
Front Load Washing Machine Model: HNS1260TVE/ME Name of the parts Detergent dispenser Top Cover Program selector Button Door handle Porthole Bottom plaque Page 12...
Front Load Washing Machine Model: HNS1260TVE/ME Opertional Functions ••• Power Switch Press this button to switch on the washing machine. Press it again to switch it off. Start / Pause Button When the washing machine is connected to the power socket and a program is selected, washing operation will start.
Page 15
Front Load Washing Machine Model: HNS1260TVE/ME Functions F: Delay Button Touch this button lightly, the washing machine will start operation after a period of time and the corresponding indicator will go on. The range is 0.5-24 hours; each touch of this button increases a half hour.
Front Load Washing Machine Model: HNS1260TVE/ME Error Display and Troubleshooting Error message:Door is not properly shut 20s after program is started. Troubleshooting: Pushing the door to Check Whether Door Shut the door properly. is properly shut or not 220-240v Cut off the power and then turn on again.
Page 18
Front Load Washing Machine Model: HNS1260TVE/ME Error message:Temperature sensor is not properly connected or damaged (display at the end of a program). Troubleshooting: Cut off power and measure the resistance NTC exist open circuit .Replace it of temperature sensor by multimeter, is...
Page 19
Front Load Washing Machine Model: HNS1260TVE/ME Error message:The required water level is not reached within 8 min Troubleshooting: Check if water is leaking from washer Readjust or replace the broken parts bottom. inlet pipe. drain pipe or other pipe connection...
Page 20
Front Load Washing Machine Model: HNS1260TVE/ME Error message. Motor overheat protection or damaged. Troubleshooting: Cut off power and check if motor wires Reconnect well are connected well Put the motor in normal temperature about Measure if resistance of motor winding by ten minutes, and then test again.
Page 21
Front Load Washing Machine Model: HNS1260TVE/ME Error message. Water level exceeds protective value. Troubleshooting: Clean water switch hose and air Check if water switch hose and air collector collector are jammed Pull out water switch inserts and turn on power, then set wash mode. While water...
Page 22
Front Load Washing Machine Model: HNS1260TVE/ME Examination & Troubleshooting Failure:Display nothing Troubleshooting: Repair power supply Measure the power supply ,is it exists 220V-240V AC voltage Press the power switch Is power switch on? Press power switch and check the voltage...
Page 23
Front Load Washing Machine Model: HNS1260TVE/ME Failure:no draining Troubleshooting: Adjust the height of drain pipe to Is the height of drain pipe too high? 80-100 cm Turn filter anticlockwise open and check if Clean and tighten filter clockwise. filter is jammed...
Page 24
Front Load Washing Machine Model: HNS1260TVE/ME Failure:water leaking Troubleshooting: Check if water is leaking from the inlet pipe Readjust it. or the tap Replace drain pipe Is drain pipe broken Remove clothes Check if there is foreign material nipped between cushion of sight window and...