Advertisement
Available languages
Available languages
Quick Links
Drive Shield Kit
Power Max
Model No. 115-5699
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
1
Removing the Belt Covers and
Cleaning the Snowthrower
Frame
No Parts Required
Procedure
1. Remove the 4 bolts that hold the belt covers in place,
and remove the belt covers.
Note: Save the screws to install the belt cover.
2. Clean and dry the top of the snowthrower frame to
remove all oil and dirt.
Important: The sealant will not adhere to a
dirty frame, and an improper seal may allow
moisture to penetrate the seal and leak onto the
friction wheel.
© 2008—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Snowthrowers
Description
No parts required
Drive shield
Bolt
Trim seal
Register at www.Toro.com.
Qty.
–
1
Install the drive shield.
2
1
Install the trim seal.
2
Installing the Drive Shield
Parts needed for this procedure:
1
Drive shield
2
Bolt
Procedure
Important: You will need a flexible silicone RTV
sealant (such as Loctite 5045 or Loctite 5905) to
complete this procedure. The sealant should be
water and oil resistant.
1. Apply 2 parallel beads of sealant to the bottom of
the drive shield (Figure 1).
Note: Do not apply sealant in the area between the
locating tabs and the front edge of the drive shield
(Figure 1).
Form No. 3361-375 Rev A
Installation Instructions
Use
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Advertisement
Related Manuals for Toro Power Max 115-5699
Summary of Contents for Toro Power Max 115-5699
- Page 1 (Figure 1). Register at www.Toro.com. © 2008—The Toro® Company Original Instructions (EN) 8111 Lyndale Avenue South Printed in the USA Bloomington, MN 55420...
- Page 2 Figure 1 1. Locating tab 3. Bead of silicone RTV sealant 2. Front edge of drive shield Figure 3 1. Drive shield 3. Small gap 2. Pull the traction idler pulley toward the side of the 2. Traction idler pulley arm frame, and slide the drive shield into place, with the mounting tabs on the outside of the frame and the Note: Insert a wedge (such as a screwdriver)
- Page 3 Installing the Trim Seal (Optional) Parts needed for this procedure: Trim seal Procedure On models with more than a 1/2-inch gap between the belt cover and the front of the engine, add the trim seal to the belt cover to further prevent moisture from entering the drive area.
- Page 4 Notes:...
- Page 5 Remarque: N'appliquez pas de mastic entre les languettes d'alignement et le bord avant de la tôle de protection (Figure 1). © 2008—The Toro® Company Enregistrez votre produit à www.Toro.com. Traduction du texte d'origine (FR) 8111 Lyndale Avenue South Imprimé aux États-Unis Bloomington, MN 55420 Tous droits réservés...
- Page 6 Figure 1 1. Languette d'alignement 3. Cordon de mastic RTV à base de silicone 2. Bord avant de la tôle de Figure 3 protection 1. Tôle de protection 3. Petit espace 2. Bras de la poulie de 2. Tirez la poulie de tension vers le côté du châssis, et tension glissez la tôle de protection en place en appuyant contre le bord avant du châssis les languettes...
- Page 7 Montage du joint de garniture (option) Pièces nécessaires pour cette opération: Joint de garniture Procédure Sur les modèles présentant un écart de plus de 1,25 cm (1/2") entre le couvercle de courroie et l'avant du moteur, ajoutez le joint de garniture sur le couvercle de courroie pour renforcer la protection contre l'humidité...