Advertisement
Quick Links
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE
AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1.
SAFETY INSTRUCTIONS
the warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that may occur. It
must be understood that common sense and caution are factors which cannot be built into this product, but must be applied by the
operator.
WARNING! USE EXTREME CAUTION when working with high voltages. IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.
WARNING! Engines produce carbon monoxide which is odourless and causes slower reaction time which could lead to serious injury.
An engine which is operating should be in a well ventilated area, or the vehicle's exhaust should be connected to an adequate fume
removal system.
DO NOT use the relay tester if it has been damaged.
DO NOT use the relay tester when hands are wet.
familiarise yourself with the fuses and relays layout, normally shown on the fuse and relay housing cover or the vehicle manual.
switch off ignition and remove ignition key when removing and replacing fuses. .
Always renew a fuse with the identical fuse and rating, never use one with a different rating or substitute anything else.
switch off ignition and remove ignition key when removing and replacing relays.
Always renew a relay with an identical relay, never use one that is similar, which may perform different functions.
familiarise yourself with the application and limitations of the relay tester.
When working on a vehicle which is being tested or repaired ensure that the handbrake is on and the front wheels are chocked to avoid
the vehicle moving and causing injury.
Wear suitable eye protection when testing or repairing a vehicle.
select the relay to be tested and follow the instructions before commencing testing.
Always take care when working with voltages above 35V Dc. these voltages are considered a shock hazard.
If any abnormal results occur, the relay tester must be checked out by an authorised technician.
When not in use, store the relay tester carefully in a safe, dry, childproof location out of direct sunlight. storage temperature range:
-15°c to +50°c.
2. INTRODUCTION
Health test for 4 and 5 pin electro-mechanical relays commonly found on modern vehicles. test feature will cycle the relay ten times, testing
the resistance, contacts and consistency within each cycle. If a cycle fails on the test then this will be indicated by a red LED and alternatively
a green LED if the relay works. supplied in zipped pouch.
red (+)
3. SPECIFICATION
© Jack sealey Limited 2013
InstructIons for:
RELAY TESTER
MoDEL no: TA131
Black (-)
Model Number:...............................TA131
Relay configuration.......................... 4 pin/5 pin
supply voltage..................................12VDc (vehicle battery)
flying lead length.............................1400mm
tester module size (L x W x D)........130mm x 70mm x 35mm
Battery connection........................... Insulated crocodile clips
Weight..............................................245g
Original Language Version
Green LED (Pass)
red LED (fail)
test button
(red)
test sockets
4 PIn / 5 PIn
selector switch
tA131 Issue: 1 - 28/03/13
Advertisement
Related Manuals for Sealey Auto Service Line TA131
Summary of Contents for Sealey Auto Service Line TA131
- Page 1 RELAY TESTER MoDEL no: TA131 thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
- Page 2 WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. INFORMATION: for a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode. Sole UK Distributor, Sealey Group, www.sealey.co.uk...