Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when building this shed.
Keep the work area clean, uncluttered and ensure there is adequate lighting.
Keep children and unauthorised persons away from the working area.
DO NOT use the shed for any purpose other than that for which it is designed.
Use appropriate safety clothing including eye protection.
The assembly of this product will require assistance.
DO NOT attempt assembly in windy conditions.
2. INTRODUCTION
Galvanized, steel panels easily assembled to form a rigid and secure shed, has skillion (sloping) roof and single door. Door is secured by cross
bolt and eyelet which will accept a padlock (not supplied) for additional security. Supplied with bolt-down fixing kit.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . GSS1515G
Overall Size: . . . . . . . . 1500 x 1500 x 1900mm
Roof Type: . . . . . . . . . . . . . . . . . . . . . . Skillion
© Jack Sealey Limited
INSTRUCTIONS FOR:
GALVANIZED STEEL SHED GREEN
1.5 X 1.5 X 1.9M
GSS1515G
MODEL NO:
Original Language Version
GSS1515G
Issue: 1 - 26/09/14
Advertisement
Related Manuals for Sealey GSS1515G
Summary of Contents for Sealey GSS1515G
- Page 1 (not supplied) for additional security. Supplied with bolt-down fixing kit. 3. SPECIFICATION Model No: ....GSS1515G Overall Size: ..1500 x 1500 x 1900mm Roof Type: .
-
Page 2: Concrete Slab
This will allow for a 50mm edge around the shed. We recommend that you slope the 50mm edges downward by 10 mm so that rain water can be drained away from the shed. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited... -
Page 3: Tools Required
Location Check Sheet 2057x770 zinc- Sheet rear wall left Sheet Sheet 2057x770 zinc- rear wall right Sheet 1977-2057x770 Sheet side wall zinc-left Sheet 1977-2057x770 Sheet side wall zinc-right Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited... - Page 4 Channel channel 674 zinc front Jamb jamb 1898 white front Jamb jamb 1898 white front Jamb jamb 775 white front lip 1601 zinc roof FITTINGS PACK Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 5 Self tapper safety cover (L type) Channel safety cover Rawl bolt (R type) In the unlikely event that you find you are missing a part, please contact your Sealey dealer. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
-
Page 6: Parts Diagram
7. PARTS DIAGRAM Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited... - Page 7 (diagram B) Note that the small lip of the channel is always facing out. This is to ensure that rain water cannot build up inside the shed. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 8 8.1.3. Now fit 31 mid wall channel to the sheeting and position it using the self tapping screws. Please note that the groove should face downwards. Position the top and bottom channels using the self tapping screws as well. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 9 This is to ensure that rain water can not build up inside the shed. Repeat the same steps for 2L and 7L the other side wall. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 10 8.3.2. Now tap or slide in 20A and 20A channels to the sheeting and fix them using the self tapping screws. 8.3.3. Now fit two 51 side lips to the sheeting and fix them using the self tapping screws. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 11 Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 12 8.4.2. Fit the 41A jamb, 42 jamb and 23 bottom channel in and fix them using the self tapping screws (not those with cross mark at this stage). Be aware of the joint details as per the diagrams). Diagram B is the same as diagram A. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 13 Fix 70 pad bolt (but NOT its keeper in this stage) to the pre-drilled holes and rivet or use self tapping screws as required. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 14 8.6.1. Attach the side walls to the back wall, then the front wall, then the roof. Fix all the components using the self tapping screws. Fix 71 pad bolt keeper with rivets or screws as required. For greater security fit rivets as below. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 15 8.6.2. Now fit the bolt down kit as per the diagram. Strengthen the mid wall brace by applying 72 the mid wall brace bracket on each corner. RAWL BOLT Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 16 8.6.3. Apply channel safety cover L type on channel 32 and R type on channel 33R. Apply the self-tapper covers on the screws fixed on the wall to prevent accidental injuries. Original Language Version GSS1515G Issue: 1 - 26/09/14 © Jack Sealey Limited...
- Page 17 8.6.4. If required, the door can be assembled on the opposite side. Align the door with the edge and drill new holes. Remove the pin from the hinge and reverse it before assembling the door. Fill the old pre-drilled holes with rivets if required. Perform the same procedure for the pad lock.