Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Toro FP-2200
Summary of Contents for Toro FP-2200
- Page 1 Form No. 3379-761 Rev A FP-2200/3000/4000 Forward Plate Compactor Model No. 68025—Serial No. 313000001 and Up Model No. 68026—Serial No. 313000001 and Up Model No. 68027—Serial No. 313000001 and Up g019691 www.discount-equipment.com *3379-761* A Original Instructions (EN)
- Page 2 We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto, Power Blanket, Nifty Lift, Atlas Copco, Chicago Pneumatic, Allmand, Miller Curber, Skyjack,...
-
Page 3: Introduction
This manual identifies potential hazards and has safety messages identified by the safety alert symbol (Figure 2), Whenever you need service, genuine Toro parts, or additional which signals a hazard that may cause serious injury or death information, contact an Authorized Service Dealer or Toro if you do not follow the recommended precautions. -
Page 4: Table Of Contents
Contents Safety Improper use or maintenance by the operator or Introduction ..............2 owner can result in injury. To reduce the potential Safety ................3 for injury, comply with these safety instructions and Safe Operating Practices........... 3 always pay attention to the safety alert symbol, which Safety and Instructional Decals ......... - Page 5 Make any necessary repairs before restarting. • Do not touch parts which may be hot from operation. • Use only genuine Toro replacement parts to ensure that Allow them to cool before attempting to maintain, adjust, original standards are maintained. or service.
-
Page 6: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 117–4979 1. Entanglement hazard, belt—keep away from moving parts; keep all guards and shields in place 93–9084 1. -
Page 7: Setup
Setup Installing the Handle Secure each side of the handle to the plate compactor frame using a bolt, flat washer, spacer, bearing, lock washer, and nut (Figure 3 or Figure 4). g019693 Figure 4 Model no. 3000/4000 1. Nut 5. Spacer 2. -
Page 8: Product Overview
Product Overview Operation Note: Determine the left and right sides of the machine from the normal operating position. Checking the Engine Oil Level Service Interval: Before each use or daily 1. Stop the machine on a level surface. 2. Set the throttle to slow, turn off the engine switch, and wait for all moving parts to stop. -
Page 9: Adding Fuel
Adding Fuel DANGER • For best results, use only clean, fresh (less than 30 days When fueling, under certain circumstances, a static old), unleaded gasoline with an octane rating of 87 or charge can develop, igniting the gasoline. A fire or higher ((R+M)/2 rating method). -
Page 10: Adding Water
g013315 Figure 8 g019702 Figure 10 1. Elastic tank latch 4. Add unleaded gasoline to the fuel tank, until the level is just inside the mesh filter basket. 3. Fill the tank with water, reassemble it to the frame, and Important: This space in the tank allows gasoline reattach the coupler. -
Page 11: Operating The Compactor
g019704 g019775 Figure 12 Figure 14 1. Fuel valve 1. Throttle 3. Move the choke lever to the left if you are starting a 5. Pull the recoil handle sharply to start the engine. cold engine (Figure 13). 6. After the engine starts, gradually move the choke to the right. -
Page 12: Transporting The Machine
Transporting the Machine The rollcage lifteye can be used to lift and transport the machine with straps or a crane (Figure 15). Alternatively, two people can transport the machine by lifting the compactor using the front and rear lift handles (Figure 15). g019776 Figure 15 1. -
Page 13: Maintenance
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Change the engine oil. After the first 25 hours • Check the engine oil level. • Clean debris from the air cleaner. Before each use or daily • Inspect the air cleaner elements. •... -
Page 14: Servicing The Engine Oil
4. Remove the cover. Every 100 hours Note: Be careful to prevent dirt and debris from WARNING falling into the base. Oil may be hot after the engine has been run, and 5. Remove the foam and paper elements from the base (Figure 17). -
Page 15: Cleaning The Sediment Cup
3. Move the fuel shut-off valve to the Off position. 4. Remove the sediment cup and O-ring (Figure 6). 5. Wash the sediment cup in a nonflammable solvent and dry it thoroughly. 6. Place the O-ring in the fuel valve and install the sediment cup, tightening it securely. -
Page 16: Servicing The Spark Plug
Storage 3. Loosen or tighten the puller bolt on the rear of the engine deck until the desired tension is obtained. 4. Replace the belt cover and the four engine mounting 1. Stop the engine, and disconnect the spark plug wire. bolts. -
Page 17: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The engine will not start, starts hard, or 1. The fuel tank is empty. 1. Fill the fuel tank with gasoline. fails to keep running. 2. The spark plug is pitted, fouled, or the 2. - Page 18 Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company. Australian Consumer Law: Australian customers will find details relating to the Australian Consumer Law either inside the box or at your local Toro Dealer.
- Page 19 We sell worldwide for the brands: Genie, Terex, JLG, MultiQuip, Mikasa, Essick, Whiteman, Mayco, Toro Stone, Diamond Products, Generac Magnum, Airman, Haulotte, Barreto, Power Blanket, Nifty Lift, Atlas Copco, Chicago Pneumatic, Allmand, Miller Curber, Skyjack,...