Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
Maintain the Impact Wrench and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the Impact Wrench is switched off before installing the battery pack.
9
Keep the Impact Wrench and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the Impact Wrench; e.g. ceilings, floors and enclosures may contain electrical items or
9
water piping
Ensure battery pack is correctly inserted into the Impact Wrench handle and latched in place before attempting to switch on Impact
9
Wrench.
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Be aware that this Impact Wrench does not need to be plugged into the mains power.
9
Keep direction switch in the locked position until the Impact Wrench is required for use.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the Impact Wrench where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the Impact Wrench.
8
DO NOT operate the Impact Wrench if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the Impact Wrench operating unattended.
8
DO NOT carry the Impact Wrench with your finger on the power switch. Keep direction switch in the locked position.
8
DO NOT use the Impact Wrench for a task it is not designed to perform.
8
DO NOT operate the Impact Wrench when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the Impact Wrench or battery charger wet or use in damp or wet locations.
8
2. INTRODUCTION
Compact, lightweight cordless impact wrench. Comfortable composite housing with soft grip to reduce vibration. Variable speed control trigger
with lock function gives more control during application. Integrated LED battery level indicator and LED work light. Supplied with belt hook for
safer storage while not in use. Requires Model No. CP1200BP 12V 1.5Ah Lithium-ion Battery and Model No. CP1200MC Battery Charger.
3. SPECIFICATION
Model No.. ................................................................. CP1204
Battery options
12V 1.5Ah Li-ion, 12V 3Ah Li-ion, 12V 4Ah Li-ion (not included)
Consumable parts
CP1200BP - Battery 12V 1.5Ah,
CP1200BP3 - Battery 12V 3Ah,
CP1200BP4 - Battery 12V 4Ah (not included)
Drive .......................................................................... 3/8" Sq
Impact rate ........................................................... 0-3500bpm
Max. torque ..................................................... 80Nm (58lb.ft)
No load speed .......................................................0-2500rpm
Noise power/pressure .......................................... 85/74dB(A)
Vibration/uncertainty ........................................ 2.898/1.5m/s²
Replacement parts ..................... CP1200MC - Mains charger
© Jack Sealey Limited
12V 3/8"SQ DRIVE CORDLESS IMPACT WRENCH
80NM - BODY ONLY
CP1204
MODEL NO:
Wear protective
Wear ear
gloves
protection
Original Language Version
Wear a mask
fig.1
CP1204 | Issue 2 11/05/20
Advertisement
Related Manuals for Sealey CP1204
Summary of Contents for Sealey CP1204
- Page 1 CP1204 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...