hit counter script
Sony HDS-7150 Installation Manual
  1. Manuals
  2. Brands
  3. Sony Manuals
  4. Switch
  5. HDS-7150
  6. Installation manual
Sony HDS-7150 Installation Manual

Sony HDS-7150 Installation Manual

Hd digital video switcher, power supply unit, switcher control panel, dme control panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

HD DIGITAL VIDEO SWITCHER
HDS-7150/7100
POWER SUPPLY UNIT
HKDS-7695/7695A
SWITCHER CONTROL PANEL
BKDS-7017/2010
DME CONTROL PANEL
BKDM-3010
HKDS-7031
HKDS-7051
HKDS-7061
HKDS-7071
HZS-7040
HZS-7060
BKDS-7001
BKDS-7003
INSTALLATION MANUAL
1st Edition (Revised 3)
BKDS-7030
BKDS-7031
BKDS-7033
BKDS-7075
BKDS-7091

Advertisement

Table of Contents
loading

Related Manuals for Sony HDS-7150

Summary of Contents for Sony HDS-7150

  • Page 1 HD DIGITAL VIDEO SWITCHER HDS-7150/7100 POWER SUPPLY UNIT HKDS-7695/7695A SWITCHER CONTROL PANEL BKDS-7017/2010 DME CONTROL PANEL BKDM-3010 HKDS-7031 BKDS-7030 HKDS-7051 BKDS-7031 HKDS-7061 BKDS-7033 HKDS-7071 BKDS-7075 HZS-7040 BKDS-7091 HZS-7060 BKDS-7001 BKDS-7003 INSTALLATION MANUAL 1st Edition (Revised 3)
  • Page 2 électrique, d'incendie ou de blessure n'effectuer que les réparations indiquées dans le mode d'emploi à moins d'être qualifié pour en effectuer d'autres. Pour toute réparation faire appel à une personne compétente uniquement. HDS-7150 Serial No. 10001 and Higher HDS-7100 Serial No.
  • Page 3 When this product is installed in a rack, please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading. 1 (P) HDS-7150/7100...

  • Page 5: Table Of Contents

    Power Switch for Service ............1-1 1-2-2. Power Specifications ..............1-1 1-2-3. Power Cord ................. 1-2 1-2-4. Connecting the HDS-7150/7100 with the Power Supply Unit ..1-3 1-3. Example of System Connection ..............1-5 2. Installation of HDS-7150/7100 2-1. External Dimensions ................... 2-1 2-2.
  • Page 6 Input and Output Signals of Connectors ............. 5-6 5-6. Removal of Bottom Panel ................5-7 5-7. Description of Switch on Board ..............5-8 5-7-1. KY-307 Board ................5-8 5-8. Adjustment of the Fader Lever ..............5-9 5-9. Installation of Switch Tip (accessory) ............5-10 HDS-7150/7100...
  • Page 7 Installation of Track Ball ................6-6 6-8. Hard Reset ....................6-7 7. Installation of Options 7-1. Installation of Options for HDS-7150/7100 ..........7-1 7-1-1. Installation Slot of Plug-in Boards ..........7-2 7-1-2. Table of HDS-7150 Plug-in Boards ........... 7-3 7-1-3.
  • Page 8 9. Set-up of HDS-7150 9-1. Overview of Operating/Saving the Set-up Data .......... 9-1 9-2. Installation of Program (HZS-7040) ............9-3 9-2-1. Downloading the Program ............9-4 9-2-2. Initializing the Nonvolatile Memory .......... 9-6 9-3. Set-up ......................9-7 9-3-1. Confirmation of the Software Version ........9-8 9-3-2.

  • Page 9: Manual Structure

    Manual Structure Purpose of this manual This manual is the installation manual of HD Digital Video Switcher HDS-7150/ 7100 and their optional boards and units. This manual is intended for use by trained system and service engineers, and describes the information on installing the HDS-7150/7100 system.

  • Page 10: Contents

    Section 8 Adjustment of Secondary Power Supply Voltage This section describes the power supply voltage adjustments required after connect- ing all the products which constitute HDS-7150/7100 system. Section 9 Set-up of HDS-7150 Section 10 Set-up of HDS-7100 These sections describe the overview of setup operation, installation of program, setup, saving the setup data to nonvolatile memory.

  • Page 11: General Information For Installation

    8 A/DC 12 V (max.), 76 A/DC 3.3 V (max.) As the inrush current at power-on is the maximum 80 A for HDS-7150/7100 and the maximum 20 A for the control panel, the capacity of the AC power must be commensurate with them. If the capacity of the AC power is not adequately large, the breaker of the AC power at the supply side will operate or the unit will abnormally operate.

  • Page 12: Power Cord

    For the customers in the United Kingdom except the United Kingdom Required Parts Required Parts Power Cord, 250 V 10 A (2.4 m) : ! 1-782-165-11 Power Cord, 250 V 10 A (2.0 m) : ! 1-551-631-22 AC inlet AC inlet HDS-7150/7100...

  • Page 13: Connecting The Hds-7150/7100 With The Power Supply Unit

    . Never use a DC power cord other than the supplied DC power cord. It may cause fire or electric shock. The HDS-7150/7100 does not have a power switch and power indicator. For the power-on/off of the HDS- 7150/7100, use the power switch of the HKDS-7695/7695A.
  • Page 14 (2) Connect the PROCESSOR A connector of the second HKDS-7695/7695A and the POWER SUPPLY 2 A connector of the HDS-7150 using the harness A (MB-PA2). Connect the PROCESSOR B connector of the HKDS-7695/7695A and the POWER SUPPLY 2 B connector of the HDS-7150 using the harness B (MB-PB2).

  • Page 15: Example Of System Connection

    1-3. Example of System Connection 1-3. Example of System Connection HDS-7150 SUB PANEL KEYER CONTROL PANEL MAIN PANEL BKDS-2010 BKDS-7060 BKDS-7017 SWER CONTROL OUT 1 SWER SWITCHER HD SDI PANEL MONITOR RS-422A (SWER) PANEL 2/ REMOTE 3 MONITOR CAMERA ME PVW...
  • Page 16 HD Routing Switcher LINE IN SWITCHER GPI DME GPI DME PANEL INPUT OUTPUT • • • • • • REF INPUT PROCESSOR SWER A TALLY INTERFACE TALLY UNIT DME CONTROL PANEL SYSTEM EDITOR BKDS-7700 BKDM-3010 BVE-9100 REF INPUT SIGNAL GENERATOR HDS-7150/7100...

  • Page 17: Installation Of Hds-7150/7100

    Section 2 Installation of HDS-7150/7100 2-1. External Dimensions 403.2 47.7 250.8 111.1 Unit : mm HDS-7150/7100...

  • Page 18: Rack Mounting

    HDS-7150/7100 2-2. Rack Mounting 2-2. Rack Mounting The HDS-7150/7100 can be mounted in a 19-inch standard rack. Be sure to use the optional Rack Mount Rail RMM-18DV. Required Parts . Rack Mount Rails (RMM-18DV) : 2 sets . Screws for plate nut (long) installing (B4 x 8) : 16 pcs .
  • Page 19 (1) Pull out the inner member while pressing the stopper of the RMM-18DV. Outer member 1 Stopper Inner member (2) Secure the four inner members to the HDS-7150/7100 by the 32 screws (B4 x 8) supplied with the RMM-18DV. (3) Remove the feet of the HDS-7150/7100 as required. HDS-7150/7100...
  • Page 20 HDS-7150/7100 2-2. Rack Mounting (4) Temporarily secure the bracket and the plate nut (long) to the outer member 1 by the preparated screws (B4 x 8) for fixing the plate nut (long). While sliding the outer member 2 back-and-forth, to see the screw hole of the outer member 1, attach the bracket and the plate nut (long).
  • Page 21 HDS-7150/7100 2-2. Rack Mounting (6) Install the HDS-7150/7100 in the rack while releasing the stoppers of the inner members. (7) After confirming that the unit can be moved smoothly, tighten the screws temporarily secured in the step (5). Rack Outer member 2 HDS-7150/7100 .
  • Page 22 Outer member Ornamental washer RK5 x 16 Ornamental washer . When HDS-7150/7100 is mounted in a rack, the maximum moving distance is illustrated below. Maximum moving distance Distance to slide rail center Set height when mounted in rack Unit : mm...

  • Page 23: Matching Connectors

    2-3. Matching Connectors When connecting cables to various connectors on the rear panel at the time of installing, connecting or servicing, connect the following connectors or their equivalents. 2-3-1. HDS-7150 Connector indication on rear panel Connector parts No. and name (cable side)

  • Page 24: Hds-7100

    HDS-7150/7100 2-3. Matching Connectors 2-3-2. HDS-7100 Connector indication on rear panel Connector parts No. and name (cable side) SWITCHER PANEL (SWER) D-sub 9-pin, Male Connector 9-pin, Male : 1-560-651-00 EXT DME 1 Junction Shell 9-pin : 1-561-749-00 SERIAL TALLY DME PANEL...

  • Page 25: Input And Output Signals Of Connectors

    HDS-7150/7100 2-4. Input and Output Signals of Connectors 2-4. Input and Output Signals of Connectors The input and output signals of the connectors on the rear panel are specified in the following table. And refer to the following illustration for the pin positions of the connectors.
  • Page 26 HDS-7150/7100 2-4. Input and Output Signals of Connectors HDS-7100 [D-sub 56-pin, Female] EXT VIEW POWER SUPPLY 1 POWER SUPPLY 1 [D-sub 25-pin, Female] EDIT PVW OUTPUTS EXT VIEW [D-sub 15-pin, Female] EXT VIEW [D-sub 9-pin, Female] EXT VIEW Rear panel...
  • Page 27 HDS-7150/7100 2-4. Input and Output Signals of Connectors SWITCHER PANEL : RS-422A (D-sub 9-pin, Female) The <CONTROLLER> indicates the controlling device. <DEVICE> from Control Panel BKDS-7017, etc. The <DEVICE> indicates the controlled device. Pin No. Signal Name Function Frame ground POWER SUPPLY 1-A, 2-A : (D-sub 56-pin, Female) <DEVICE>...
  • Page 28 HDS-7150/7100 2-4. Input and Output Signals of Connectors EDITOR A/REMOTE 1 : RS-422A (D-sub 9-pin, Female) EXT DME 1, 2 : RS-422A (D-sub 9-pin, Female) <DEVICE> from Editor <DEVICE> from HD Digital Multi Effects HDME-7000, etc. Pin No. Signal Name Function Pin No.
  • Page 29 HDS-7150/7100 2-4. Input and Output Signals of Connectors DME PANEL : RS-422A (D-sub 25-pin, Female) SWITCHER GPI, DME GPI : (D-sub 25-pin, Female) TTL input x 8 to Adaptor Box (BKDS-7075) Relay contact output x 4 (max. 30 V AC/DC, 0.1A) Pin No.

  • Page 30: Removal Of Front Panel

    HDS-7150/7100 2-5. Removal of Front Panel 2-5. Removal of Front Panel (1) Loosen the six fixing screws on the front panel. The screws have the drop-safe. (2) Remove the front panel in the direction of the arrow. Fixing screws Front panel...

  • Page 31: Removal Of Parts On The Front Side

    HDS-7150/7100 2-6. Removal of Parts on the Front Side 2-6. Removal of Parts on the Front Side (1) Remove the front panel. (Refer to Section 2-5.) (2) Remove the ten screws on the two board retainers and the one board holder.

  • Page 32: Description Of Switches And Leds On Boards

    HDS-7150/7100 2-7. Description of Switches and LEDs on Boards 2-7. Description of Switches and LEDs on Boards The address on the board is shown in the parentheses. 2-7-1. Power Indicators on CKG-26/CPU-183/CRK-9/DI-37/DLP-17/DSK-16/MEM- 65C/MEM-65K/MEM-65Y/MIX-43/MPU-111/OUT-20/VSE-19/VSE-20/VSE-21/ VSW-66/WKG-29 Boards The following boards (including the optional boards) have the LEDs indicating status of +5 V, +3 V, +12 V, _5 V and other power supplies.
  • Page 33 SLOT NO. 1 NO. 16 The +5 V, +3 V, _5 V and _12 V are supplied from the power supply unit HKDS-7695/7695A to the HDS-7150/7100 and optional boards. The power indicators light when the power is supplied. The power indicators go out when the power is not supplied or fuses on the boards are blown.

  • Page 34: Board

    HDS-7150/7100 2-7. Description of Switches and LEDs on Boards 2-7-2. CKG-26 Board Top side COP7 COP8 COP9 Pin header COP10 COP11 COP12 3.3 V GND _5 V VCC VDD VEE Front side A side (Component side) CN9 (Q-9) : +5 V (A) TEST terminal The +5 V (A) voltage measurement terminal.
  • Page 35 HDS-7150/7100 2-7. Description of Switches and LEDs on Boards S1 (Q-8) : Mode setting switch This switch is used for the factory setting. Set all knobs to ON position for normal operation. indicates the knob position. COP2, COP3, COP4, COP5, COP6, and COP7 (P-7) : Mode setting connector pin These jumpers are used for the factory setting.

  • Page 36: Board (Hds-7150/Hds-7100/Hkds-7071)

    S2 (Q-5) : RESET switch Use the RESET switch to re-start forcibly the system by means of hardware. When this switch is pressed, the HDS-7150/7100 perform the same operation as the power-on sequence. However, the resume function is not operated.

  • Page 37: Board

    HDS-7150/7100 2-7. Description of Switches and LEDs on Boards 2-7-4. DI-37 Board Top side _2 V +1.2 V CRCC 1 2 9 10 11 12 13 14 15 _2 V Front side A side (Component side) D20, D21, D22, D23, D24, D25, D26, D27 (Q-8), D28, D29, D30, D31, D32, D33, and D34 (Q-9) :...

  • Page 39: Installation Of Hkds-7695/7695A

    Section 3 Installation of HKDS-7695/7695A 3-1. External Dimensions 304.8 73.7 101.6 Unit : mm HDS-7150/7100...

  • Page 40: Rack Mounting

    4 pcs . Ornamental washers for rack mounting : 4 pcs (Sony part number : 2-297-913-00) Be sure to fix the rack to the floor with bolts. When the unit is pulled out from the rack, this will prevent its fall.
  • Page 41 (2) Secure the two inner members to the HKDS-7695/7695A by the six screws (B4 x 8) supplied with the RMM-30. (3) Remove the feet of the HKDS-7695/7695A. B4 x 8 HKDS-7695/7695A Inner member Inner member Feet B4 x 8 HDS-7150/7100...
  • Page 42 (5) Temporarily secure the front and rear brackets to the outside of the rack by the eight screws (B 5 x 8) supplied with the RMM-30. Rack Rack 12.7 Outer members 31.75 12.7 31.75 12.7 B 5 x 8 B 5 x 8 Front bracket Rear bracket HDS-7150/7100...
  • Page 43 When using the two units of HKDS-7695/7695A (Used for redundant power supply) Rack Outer member HKDS-7695/7695A Stoppers Inner members A combination of the HKDS-7695 and the HKDS-7695A is not allowed. Use two power supply units of the same model. HDS-7150/7100...
  • Page 44 RK5 x 16 Outer member Ornamental washer . When the HKDS-7695/7695A is mounted in a rack, the maximum moving distance is illustrated below. Maximum moving distance Distance to slide rail center Set height when mounted in rack Unit : mm HDS-7150/7100...

  • Page 45: Notes When Using Hkds-7695/7695A Without Mounting In A Rack

    3-3. Notes when Using HKDS-7695/7695A without Mounting in a Rack When the HKDS-7695/7695A is placed on top of the HDS-7150/7100 without installing in a rack, be sure to fix the HKDS-7695/7695A to the HDS-7150/7100 with the connecting metals (supplied with the HKDS- 7695/7695A).

  • Page 46: Input And Output Signals Of Connectors

    >PBT+GF30< EXT VIEW Rear panel Pin position The <DEVICE> indicates the controlled device. PROCESSOR A : (D-sub 56-pin, Female) PROCESSOR B : (D-sub 56-pin, Female) <DEVICE> from HDS-7150/7100 <DEVICE> from HDS-7150/7100 Pin No. Signal Name Function Pin No. Signal Name...

  • Page 47: Installation Of Bkds-7017

    Section 4 Installation of BKDS-7017 4-1. External Dimensions 76.8 TOP MENU UTILITY AUX DELEGATION PGM/PST DOWNSTREAM KEYER Unit : mm HDS-7150/7100...

  • Page 48: Installation Space To Console

    Extension panel : adaptor box BKDS-7075 Unit : mm 2-M4 4-2. Installation Space to Console The BKDS-7017 can be installed in the console by drilling the holes of the following specifications in the console. 11-M4 about 75d Unit : mm HDS-7150/7100...

  • Page 49: Installation In Console

    (For the details of the power supply cord, refer to Section 1-2-3.) *1 : The following solderless contact must be used for the plug. AWG #18 to #22 : 1-566-493-21 AWG #22 to #24 : 1-564-774-11 AWG #24 to #30 : 1-564-775-11 HDS-7150/7100...

  • Page 50: Input And Output Signals Of Connectors

    *1 : BKDS-7001 (Option : IF-523 board) is required for the REMOTE 1 to 4. DME : RS-422A (D-sub 9-pin, Female) TERMINAL 1, 2 : RS-232C (D-sub 9-pin, Female) <CONTROLLER> to HD Digital Multi Effects HDME- to Terminal 7000 or to HDS-7150. Pin No. Signal Name Function Pin No.
  • Page 51 LED light disable signal Ground Control signal for switch read and LED light Switch read data Ground TSEQ Control signal for character display TQCLK Control signal for character display +12 V Power supply +12 V +12 V Power supply +12 V Ground HDS-7150/7100...

  • Page 52: Opening And Closing Of Panel

    (3) Push up the panel and open it. Panel Slide knob Slide knob Slide knob (4) Close the panel and push down the panel until the slide knobs are locked. (5) Tighten the screws of the slide knobs at both sides of the panel. HDS-7150/7100...

  • Page 53: Description Of Switches And Leds On Boards

    COP1 (E-3) : This is used to select the mode corresponding to the synchronized signal that is connected to the SWITCHER on the rear panel. For HDS-7150/7100, this is opened under normal status. COP3 (E-3) : This is used to select the RS-232C signal that is connected to the TERMINAL 2 on the rear panel.
  • Page 54 S5 (N-1) : SUB CPU switch This switch is used to select the operation mode of SUB CPU. Factory setting : All OFF indicates the knob position. (1) Selection under normal status Set this switch as follows for normal operation. HDS-7150/7100...

  • Page 55: Cn-1150 Board

    When the +12 V source provides to the CN5 through CN18 on the CN-1150 board, this LED lights. D5 (Green) (D-1) : When the +5 V source provides to the CN5 through CN18 on the CN-1150 board, this LED lights. HDS-7150/7100...

  • Page 56: Board (Bkds-7071/7091)

    * : The LED (D9) of the power supply unit that is not operating correctly lights off. RV1 (D-2) : Used for +12 V power supply voltage. (Refer to Section 8-2-1.) RV2 (D-3) : Used for +5 V power supply voltage. (Refer to Section 8-2-1.) 4-10 HDS-7150/7100...

  • Page 57: Adjustment Of Fader Lever

    2 : If turning the screw clockwise, the operating force of the fader lever becomes heavier. 3 : If turning the screw counterclockwise, the operating force of the fader lever becomes lighter. Fader assembly L shaped hex. wrench (4.0 mm) Screw * This is the illustration of the BKDS-7017. 4-11 HDS-7150/7100...

  • Page 58: Installation Of Switch Tip (Accessory)

    (4) Insert the switch tip (key top sheet) between diffusion plate (milky white color) and key top (clear) as shown below, and assemble them by pushing in the key. Key top Switch tip Diffusion plate Cap pull tool 4-12 HDS-7150/7100...

  • Page 59: Hard Reset

    4-10. Hard Reset 4-10. Hard Reset (1) Open the panel. (Refer to Section 4-6.) (2) Press the RESET switch (S1) on the CPU-246 board in the control panel. Or, turn off/on the power switch. (Refer to Section 7-2-1.) 4-13 HDS-7150/7100...

  • Page 61: Installation Of Bkds-2010

    Section 5 Installation of BKDS-2010 5-1. External Dimensions 177.9 17.9 119.7 59.2 29.5 23.5 Unit : mm HDS-7150/7100...

  • Page 62: Installation Space

    The BKDS-2010 can be installed in the console by drilling the holes of the following specifications in the console. Also the unit can be installed in the SONY standard console (19-inch type) by using the rack mount metal (RMM-3000) of an optional accessory. For the details, refer to “5-3. Installation in Console”.

  • Page 63: Installation In Console

    BKDS-2010 5-3. Installation in Console 5-3. Installation in Console The BKDS-2010 can be installed in the SONY standard console (19-inch type) by using the Rack Mount Metal (RMM-3000) of an optional accessory. Prepared Parts Rack Mount Metal RMM-3000 The RMM-3000 is supplied with the following parts.
  • Page 64 5-3. Installation in Console (2) Attach the fixtures to the BKDS-2010 with the four screws. BKDS-2010 PTPWH3 PTPWH3 Fixture (L) Fixture (R) PTPWH3 (3) Secure the BKDS-2010 on the console with four washers and screws. Washer Washer Washer Washer Console HDS-7150/7100...

  • Page 65: Matching Connectors

    (For the details of the power cord, refer to Section 1-2-3.) *1 : The following solderless contact must be used for the plug. AWG #18 to #22 : 1-566-493-21 AWG #22 to #24 : 1-564-774-11 AWG #24 to #30 : 1-564-775-11 HDS-7150/7100...

  • Page 66: Input And Output Signals Of Connectors

    AC IN (3-pin AC Connector x 1) AC Power Input Pin No. Signal Name Function Frame ground RX-A Received data (_) TX-B Transmitted data (+) TX-COM Signal ground RX-COM Signal ground RX-B Received data (+) TX-A Transmitted data (_) Frame ground HDS-7150/7100...

  • Page 67: Removal Of Bottom Panel

    PWH3 x 5 PWH3 x 5 Bottom panel (2) Disconnect the two connectors (CN83 and CN84) on the CN-980 board and one connector (CN1) on the KY-307 board, then remove the bottom panel. CN84 CN83 CN-980 board KY-307 board HDS-7150/7100...

  • Page 68: Description Of Switch On Board

    BKDS-2010 can not be hard reset. ON : Reset disable OFF : Factory setting S201 (D-6) : MODE switch bit1 to 6, and 8 : Only used in Factory. Do not set to ON. bit7 : Reset setting Factory setting : All OFF position HDS-7150/7100...

  • Page 69: Adjustment Of The Fader Lever

    The operating force can be adjusted by turning the specsified screw. 2 : If turning the screw clockwise, the operating force of the fader lever becomes heavier. 3 : If turning the screw counterclockwise, the operating force of the fader lever becomes lighter. Phillips screwdriver Screw HDS-7150/7100...

  • Page 70: Installation Of Switch Tip (Accessory)

    (4) Insert the switch tip (key top sheet) between diffusion plate (milky white color) and key top (clear) as shown below, and assemble them by pushing in the key. Key top Switch tip Diffusion plate Cap pull tool 5-10 HDS-7150/7100...

  • Page 71: Installation Of Bkdm-3010

    Section 6 Installation of BKDM-3010 6-1. External Dimensions 23.5 ( 408 ) Unit : mm 6-2. Installation Space The BKDM-3010 can be installed in a console. Unit : mm HDS-7150/7100...

  • Page 72: Matching Connectors

    Connector indication on rear panel Connector parts No. and name (cable side) PROCESSOR D-sub 25-pin, Male Connector 25-pin, Male : 1-560-904-11 Junction Shell 25-pin : 1-563-377-11 MONITOR Supplied with a CPD-15SF8 SPARE A PCY-330 or a Microsoft mouse HDS-7150/7100...

  • Page 73: Input And Output Signals Of Connectors

    0.714 V p-p (± 10%) /75 Z Data terminal ready Blue output 0.714 V p-p (± 10%) /75 Z Signal ground Ground Request to send Ground Ground Ground Ground Ground H sync H sync output (TTL level) V sync V sync output (TTL level) HDS-7150/7100...

  • Page 74: Removal Of Bottom Panel

    BKDM-3010 6-4. Input and Output Signals of Connectors 6-5. Removal of Bottom Panel 6-5. Removal of Bottom Panel PROCESSOR : RS-422A (D-sub 25-pin, Female) <CONTROLLER> to HDS-7150/7100 etc. (1) Turn BKDM-3010 upside down. Pin No. Signal Name Function (2) Remove the six screws shown in the figure, then open...

  • Page 75: Description Of Switches On Board

    Used for operation check. S2-6 : Connects TX-A and RX-A signals internally. Used for operation check. S2-7, 8 : CN1 test switch S2-7 : Connects TXD and RXD signals internally. Used for operation check. S2-8 : Inputs RXD signal to connector (CN1). HDS-7150/7100...

  • Page 76: Installation Of Track Ball

    Track ball Z sensor plate (4) Push in the Z-ring while pressing it against the Z sensor plate. (5) Turn the ball cover clockwise and tighten it. Z-ring Track ball Z-ring Z sensor plate Z sensor plate Track ball HDS-7150/7100...

  • Page 77: Hard Reset

    LEFT RIGHT (2) This initial screen appears on the menu monitor. (ex) 0 TOP MENU BKGD FREZE VIDEO PATH EDGE RECUR CTRL UTLTY NON- LIGHT STATS SET/ LINEAR DIAG T TRGT SKW/ASP X 12.1116 Y 1.0002 Z -90.1118 PAGE-12 HDS-7150/7100...

  • Page 79: Installation Of Options

    Operation Software with Manual (E) for HDS-7100 *1 : For the installation of the HZS-7040, refer to “Section 9 Set-up of HDS-7150” and User’s Guide. *2 : For the installation of the HZS-7060, refer to “Section 10 Set-up of HDS-7100” and User’s Guide.

  • Page 80: Installation Slot Of Plug-In Boards

    The slot number and a name of the plug-in board to be installed in the slot are indicated at the upper side of the chassis in the HDS-7150/7100. Each optional board should also be installed at the specified slot according to the slot number as well as the standard board.

  • Page 81: Table Of Hds-7150 Plug-In Boards

    7-1. Installation of Options for HDS-7150/7100 7-1-2. Table of HDS-7150 Plug-in Boards Slot No. Optional Board Standard Board Board Function 1 MEM-87 1 Memory board 2 MEM-103 2 Memory board 3 CPU-183C 3 CPU board 4 CKG-26A 4 Clock generator board...
  • Page 82 7-1. Installation of Options for HDS-7150/7100 Slot No. Optional Board Standard Board Board Function HKDS-7071 (Option) !; VSE-21 !; Recursive prosessor (K) !' CRK-9 !' Chromakey board HKDS-7031 (Option) !, WKG-26 !, Wipe generator board !. MIX-43 !. Mixer board...

  • Page 83: Table Of Hds-7100 Plug-In Boards

    7-1. Installation of Options for HDS-7150/7100 7-1-3. Table of HDS-7100 Plug-in Boards Slot No. Optional Board Standard Board Board Function 1 MEM-87 1 Memory board 2 MEM-103 2 Memory board 3 CPU-183C 3 CPU board 4 CKG-26 4 Clock generator board...
  • Page 84 7-1. Installation of Options for HDS-7150/7100 Slot No. Optional Board Standard Board Board Function HKDS-7071 (Option) !; VSE-21 !; Recursive prosessor (K) !' CRK-9 !' Chromakey board HKDS-7031 (Option)) !, WKG-26 !, Wipe generator board !. MIX-43 !. Mixer board...

  • Page 85: Installation Of Hkds-7031/7061/7071

    7-1. Installation of Options for HDS-7150/7100 7-1-4. Installation of HKDS-7031/7061/7071 Be sure to turn off the power switch (on the HKDS-7695/7695A) before installing or removing the plug-in boards. If not, it will damage the boards or cause an electric shock.

  • Page 86: Installation Of Hkds-7051

    7-1. Installation of Options for HDS-7150/7100 7-1-5. Installation of HKDS-7051 The CCR-1827 board (HKDS-7051 : Color correction board) is installed on the VSW-66 board of slot 13. (1) Remove the front panel. (Refer to Section 2-5.) (2) Remove the two board retainers and the board holder. (Refer to “2-6. Removal of Parts on the Front”.)

  • Page 87: Installation Of Options For Bkds-7071

    . For the fader lever operating force adjustment of the BKDS-7030, refer to Section 4-8. 7-2-1. Turning On/Off the Power (1) Open the panel. (Refer to Section 4-6.) (2) Turn off the power switches A and B in the control panel. Panel Power switch A Power switch B Slide knobs (right and Left) HDS-7150/7100...

  • Page 88: Installation Of Bkds-7001

    PSW3 x 8 (5) Turn on the power switches in the control panel. (If the one power unit is installed, turn on the power switch of the side that the power unit is installed in.) (6) Close the panel. 7-10 HDS-7150/7100...

  • Page 89: Installation Of Bkds-7003

    (5) Install the DC-92 board on the KY-389A, KY-389B, or KY-441 board using the two screws for board support supplied with the BKDS-7003. Screws for board support DC-92 board Screws for board support DC-92 board (For KY-389A/389B board) KY-389A/389B/441 board CN15 CN16 (For KY-389A/389B board) 7-11 HDS-7150/7100...
  • Page 90 LE-148 board P2.6 x 5 P2.6 x 5 P2.6 x 5 KY-389A/389B/441 board (For LE-147/180 board) (For LE-148 board) Install the KY-389A, KY-389B, or KY-441 board. Turn on the power switch in the control panel. (10) Close the panel. 7-12 HDS-7150/7100...

  • Page 91: Installation Of Bkds-7030/7031/7033

    Harness (CTRL5) : 1 pc Harness (DC9) : 1 pc Screws (PSW3 x 8) : 4 pcs Installation to Adaptor Box (BKDS-7075) (1) Remove the two screws then remove the AD panel. B3 x 5 AD panel B3 x 5 7-13 HDS-7150/7100...
  • Page 92 PWH3 x 8 (3) Connect the three harnesses of the IF-629 board to the CN1 through CN3 on the KY-328/329/395C board. KY-328/329/395C board IF-629 board White (4) Secure the AD panel to the adaptor box by the two screws. 7-14 HDS-7150/7100...

  • Page 93: Joining Of Bkds-7075

    . Removal and installation of IF-629 board . Joining of adaptor box . Joining of AD panel IF-629 board Vertical direction Horizontal direction Type-B Type-A Type-C IF-629 boards Type-B Vertical and horizontal direction Type-C Type-B Type-D Type-A Type-A Type-C 7-15 HDS-7150/7100...
  • Page 94 (3) Install the IF-629 board according to the type using the six screws as shown. Type-A (Factory setting) Type-B IF-629 board IF-629 board Type-C Type-D IF-629 board IF-629 board (4) Install the three connectors and the caps except CN4 on the IF-629 board. (5) Install the AD panel to the adaptor box. 7-16 HDS-7150/7100...
  • Page 95 (2) Insert in the nylon rivet. (3) Insert in the joint brackets. (In the case of the vertical direction) Joint bracket Joint bracket Nylon rivet (In the case of the horizontal direction) Joint bracket Nylon rivet Joint bracket 7-17 HDS-7150/7100...
  • Page 96 B3 x 5 Boss Boss Joint Boss B3 x 5 * When you want to join the panels in both vertical and horizontal direction, join the panels to the vertical direction after joining them to the horizontal direction. 7-18 HDS-7150/7100...

  • Page 97: Connection Of Bkds-7017 And Bkds-7075

    7-2. Installation of Options for BKDS-7071 7-2-6. Connection of BKDS-7017 and BKDS-7075 Connect the adaptor box to the BKDS-7017 using the BVS cables. Adaptor ( BKDS-7075 ) OPTION PANEL Control Panel (BKDS-7017) *1 : Use the BVS cables (1-574-993-11). 7-19 HDS-7150/7100...

  • Page 98: Installation Of Bkds-7091

    (4) Turn the levers at both sides of the power unit in the direction of the allow. (5) Secure BKDS-7091 to the control panel by the two screws supplied with the BKDS-7091. Lever PS3 x 6 PS3 x 6 BKDS-7091 (6) Turn on the power switches in the control panel. (7) Close the panel. 7-20 HDS-7150/7100...

  • Page 99: Adjustment Of Secondary Power Supply Voltage

    8-1. HDS-7150/7100 (HKDS-7695/7695A) The HDS-7150/7100 has the five power supplies of +5 V (A), +5 V (B), +5 V (C), +3 V, +12 V, and _5 V. The CKG-26 board has the test terminals to which the probe of the digital voltmeter can be connected for measuring the power supply voltages of +5 V (A), +3 V and _5 V.

  • Page 100: Power Supply Voltage Adjustment With Hkds-7695

    180d. (Refer to the following illustra- (Refer to the following illustration.) tion.) (3) Remove the front panel of the HDS-7150/7100. (Refer (3) Turn off the power switch of the power unit B. to “2-5. Removal of Front Panel”.) (4) Perform the procedure A.
  • Page 101 8-1. HDS-7150/7100 (HKDS-7695/7695A) HDS-7150/7100 3.3 V _5 V CN-1539 board CN-1539 SLOT 1 SLOT 13 SLOT 16 Pin 4 OUT-20 CN51 +5 V CN52 VSW-66 CN9 (Q9) CN10 (Q9) 3.3 V CKG-26 board CN11 (Q9) +5 V _5 V CN12 (Q9)

  • Page 102: Power Supply Voltage Adjustment With Hkds-7695A

    180d. (Refer to the following (Refer to the following illustration.) illustration.) (3) Remove the front panel of the HDS-7150/7100. (Refer (3) Switch the redundant switches of the power unit A to “2-5. Removal of Front Panel”.) and power unit B to “2”.
  • Page 103 8-1. HDS-7150/7100 (HKDS-7695/7695A) HDS-7150/7100 3.3 V _5 V CN-1539 board CN-1539 SLOT 1 SLOT 13 SLOT 16 Pin 4 OUT-20 CN51 +5 V CN52 VSW-66 CN9 (Q9) CN10 (Q9) 3.3 V CKG-26 board CN11 (Q9) +5 V _5 V CN12 (Q9)

  • Page 104: Bkds-7017

    (2) Perform the procedure A. (3) Turn off the power switch A of the power unit A and turn on the power switch B of the power unit B. (4) Confirm that the indicators (D1 through D5) on the CN-1150 board light. HDS-7150/7100...
  • Page 105 Specifications Test connector Adjustment potentiometer +5.10 ± 0.02 V +5 V CN-1150 board RE-146 board TP2 (+5 V) 5 E1 (GND) 1RV2 +12.24 ± 0.02 V +12 V CN-1150 board RE-146 board TP1 (+12 V) 5 E1 (GND) 1RV1 HDS-7150/7100...

  • Page 107: Set-Up Of Hds-7150

    Section 9 Set-up of HDS-7150 The control panel BKDS-7017 is used for the set-up of the HDS-7150. This section describes the installation of operating program, the set-up required in the construction of system, and the saving of set-up data for HDS-7150 system.
  • Page 108 HDS-7150 9-1. Overview of Operating/Saving the Set-up Data Keys and Display of Control Panel The keys and display are named as follows. . How keys are displayed : ex.) [1] (SYSTEM) This means that “SYSTEM” is indicated on the display in the right side of the item selector button [1].

  • Page 109: Installation Of Program (Hzs-7040)

    9-2. Installation of Program (HZS-7040) 9-2. Installation of Program (HZS-7040) Before using the HDS-7150 system, the operating program of the HZS-7040 (Optional Operation Soft- ware) is installed to the flash memory in the system. The program on the flash memory is not cleared by turning on/off the power.

  • Page 110: Downloading The Program

    HDS-7150 9-2. Installation of Program (HZS-7040) 9-2-1. Downloading the Program (1) In the set-up menu screen, press the keys on the display panel in the following sequence. [1] (SYSTEM), [F10] (INSTALL) The function key indications change as follows. HDS7150 EXEC SYSTEM (2) Press the [F2] (HDS7150 SYSTEM) key (highlight indication), then press the [F10] (EXEC) key.
  • Page 111 (8) When loading is completed, “Load Complete. Insert the OPERATING PROGRAM 3.” is indicated, and the function key indications change as follows. Because the OPERATING PROGRAM 3 is not used in the HDS-7150, press the [F10] (EXEC) to end the installation of the program.

  • Page 112: Initializing The Nonvolatile Memory

    HDS-7150 9-2. Installation of Program (HZS-7040) 9-2-2. Initializing the Nonvolatile Memory (1) In the set-up menu screen, press the keys on the display panel in the following sequence. [1] (SYSTEM), [F5] (BACKUP) The function key indications change as follows. SETUP LOCK...

  • Page 113: Set-Up

    HDS-7150 9-3. Set-up 9-3. Set-up The processes to construct the system are described below. Basically set up in the following sequence. However, it is not necessary to set the item again whose setting is not changed. 1. Confirmation of the Software Version 2.
  • Page 114 HDS-7150 9-3. Set-up 9-3-1. Confirmation of the Software Version In the set-up menu screen, press the keys on the display panel in the following sequence. [1] (SYSTEM), [F7] (INFOR-MATION) The software’s and the ROM’s versions installed in each product are displayed.
  • Page 115 HDS-7150 9-3. Set-up Press the [F4] (SCREEN) key. The function key indications change as follows. SCREEN 16:9 EXEC Press the [F4] (4:3) or [F5] (16:9) key according to the aspect ratio of the screen, and press the [F10] (EXEC) key.

  • Page 116: Setting Of The Crosspoint Table

    BKDS-7017 does not require the setting of the crosspoint table because the crosspoint table is used normally without changing. Proceed to “9-3-4. Assigning of the Crosspoint”. When another switcher control panel such as BKDS-2010 is connected to the HDS-7150 and it requires to assign the different crosspoint with the BKDS-7017, perform this setting.

  • Page 117: Assigning Of The Crosspoint

    HDS-7150 9-3. Set-up 9-3-4. Assigning of the Crosspoint (1) In the set-up menu screen, press the keys on the display panel in the following sequence. [5] (OPERATION), [F3] (XPT ASSIGN) The function key indications change as follows. BUTTON SOURCE SOURCE...

  • Page 118: Assigning Of Dme (Digital Multi Effects)

    HDS-7150 9-3. Set-up Press the [F8] (NAME SELECT) key, [(], or [)] key to move the cursor to the desired name. If the desired name is not displayed in the name list, select the “USER”. Press the [F6] (SELECT) key.
  • Page 119 The internal DME and external DME cannnot be used at the same time. The internal DME and external DME differ in the signals between the HDS-7150 and DME. When the internal DME is selected. The input and output signals are fixed as follows automatically.

  • Page 120: Assigning Of The Key Sources To Key Fill

    HDS-7150 9-3. Set-up 9-3-6. Assigning of the Key Sources to Key Fill (When the Key Source Auto Select Mode is Selected) (1) In the set-up menu screen, press the keys on the display panel in the following sequence. [5] (OPERATION), [F4] (AUTO SELECT) The function key indications change as follows.

  • Page 121: Setting Of The Switcher Output Signal 1

    HDS-7150 9-3. Set-up 9-3-8. Setting of the Switcher Output Signal 1 (1) In the set-up menu screen, press the keys on the display panel in the following sequence. [2] (INPUT/OUTPUT), [F4] (SWER OUTPUT), [F3] (OUTPUT ADJUST1) The function key indications change as follows.

  • Page 122: Setting About The Change Of Synchronization Signal Assignment

    HDS-7150 9-3. Set-up 9-3-10. Setting about the Change of Synchronization Signal Assignment This setting is valid only when the frequency mode is set to 59.94 or 60.00. (1) In the set-up menu screen, press the keys on the display panel in the following sequence.

  • Page 123: Setting Of The Internal Generation Matte Signal

    HDS-7150 9-3. Set-up 9-3-11. Setting of the Internal Generation Matte Signal (1) In the set-up menu screen, press the keys on the display panel in the following sequence. [3] (EFFECT), [F5] (MATTE) The function key indications change as follows. LUM LEVEL...

  • Page 124: Setting Of The Gpi Input

    HDS-7150 9-3. Set-up 9-3-12. Setting of the GPI Input Before starting this setting, select the GPI port to “DISABLE” with the port enable function of the MISC menu. (For the selection, refer to User’s Guide HZS-7040) After this setting, return the GPI port to “ENABLE”.

  • Page 125: Setting Of The Gpi Output

    HDS-7150 9-3. Set-up 9-3-13. Setting of the GPI Output (1) In the set-up menu screen, press the keys on the function panel in the following sequence. [4] (PERIPH), [F8] (GPI OUTPUT) The function key indications change as follows. PORT TRIGGER...

  • Page 126: Setting Of The Operation Mode

    HDS-7150 9-3. Set-up 9-3-14. Setting of the Operation Mode (1) In the set-up menu screen, press the keys on the display panel in the following sequence. [5] (OPERATION), [F5] (OPERAT MODE) The function key indications change as follows. SHIFT CUSTOM...

  • Page 127: Saving Set-Up Data To Nonvolatile Memory

    After the backup is completed, “BACKUP OK” is indicated on the display. The set-up required in the construction of the system is completed. HDS-7150 has many set-up systems besides these settings. If required, the set-up data can be saved to the floppy disk. For those contents and operation, refer to the following user’s guide (option).

  • Page 129: Set-Up Of Hds-7100

    . Resume function ON/OFF Nonvolatile memory Memory pack 1 : MEM SAVE SETUP 2 : MEM LOAD SETUP 3 : SETUP SYSTEM SAVE 4 : POWER ON or SETUP SYSTEM INIT RESET 5 : SETUP SYSTEM INIT CLEAR 10-1 HDS-7150/7100...
  • Page 130 * * * * * : Replacing the key top of the HZS-7060 The 17 key tops shown above are supplied with the HZS-7060. Replace the specified key tops shown in the above figure with these key tops. For details of using the key top punching tool, see Section 5-9. 10-2 HDS-7150/7100...

  • Page 131: Installation Of Program

    To load the program from the ROM pack for the HDS-7100 for the first time, do the following. (1) Insert the ROM pack 2 (OPERATING PROGRAM 2) for upgrading supplied with the HZS-7060 to the specified position of the rear panel of the BKDS-2010. ROM pack 10-3 HDS-7150/7100...
  • Page 132 Downloading of the software starts. After loading ends, the processor and the control panel return to the state when the main power is turned on. (6) Remove the ROM pack 2 and insert the ROM pack 1 (OPERATING PROGRAM 1). 10-4 HDS-7150/7100...
  • Page 133 After loading ends, the processor and the control panel return to the state when the main power is turned on. The ROM pack is required to perform the above operations. After loading ends, the system can be used without the ROM pack. 10-5 HDS-7150/7100...

  • Page 134: Initializing The Nonvolatile Memory

    (3) Press [F3] (CLEAR). The function key indication changes as shown below. SYSTM want clear SYSTEM? INIT (4) Press [F5] (YES). The switchers are reset and the RAM is initialized (cleared). (5) Press the SETUP button. The set-up menu is displayed. 10-6 HDS-7150/7100...
  • Page 135 . Load the set-up data and snapshot data in the memory pack. (Refer to the User’s Guide.) . Write the set-up data loaded from the memory pack to the nonvolatile memory using the system save menu of the set-up. (Refer to “10-4. Saving Set-up Data to Nonvolatile Memory.”) 10-7 HDS-7150/7100...

  • Page 136: Set-Up

    After turning on the main power and pressing the SETUP button, the initial set-up screen appears and the above items 1 to 14 can be selected. If the set-up menu screen is already displayed, the SETUP button does not need to be pressed. SETUP SYSTEM INPUT OUTPUT EFFECT PERIPH 10-8 HDS-7150/7100...
  • Page 137 To set the number of scanning lines to 1080, press [F3] (1080). The function key indication changes as follows. Would like change Line? SYSTM LINE c. Press [F5] (YES). The display returns to the state of step “a” and SELECT is displayed under the selected number of scanning lines. 10-9 HDS-7150/7100...
  • Page 138 - - - - - FREQ c. Press [F6] (MORE) and the function key indication changes as follows. SYSTM 23.98 MORE - - - - - - - - - - - - - - - - - - - - FREQ 10-10 HDS-7150/7100...
  • Page 139 - - - - - SWTCH c. To set the field to ANY, press [F2] (ANY). To set the field to F1, press [F3] (F1). To set the field to F2, press [F4] (F2). SELECT is displayed under the selected field. 10-11 HDS-7150/7100...
  • Page 140 [F5] : Setting the hour (The hour is set to 2 p.m. on the above screen.) Use 1 to 24 for setting the hour. [F6] : Setting the minute. (The minute is set to 10 on the above screen.) 10-12 HDS-7150/7100...
  • Page 141 DME2K ......Internal DME channel 2 key output signal CCR1 ......... Color Correction channel 1 output signal CCR2 ......... Color Correction channel 2 output signal (4) Press [F3] (SOURCE). The selected signal is displayed on the [F3] screen. 10-13 HDS-7150/7100...
  • Page 142 The number of the selected fill button appears on the [F2] screen. The state of the digital input signal assigned to the fill button appears on the [F4] screen. (3) Rotate knob 4 to adjust the input H phase (normally set to 0). 10-14 HDS-7150/7100...
  • Page 143 The output is changed by pressing [F2] in the following sequence. CLEAN AUX1 EDPVW (3) Press [F3] (White). Rotate knob 3 to adjust the white clip value of the luminance signal. (4) Press [F4] (Dark). Rotate knob 4 to adjust the dark clip value of the luminance signal. 10-15 HDS-7150/7100...

  • Page 144: Setting About The Change Of Synchronization Signal Assignment

    OFF : The original synchronization signal is not used but synchronization signal from other source is used instead. If both input ([F3]) and output ([F5]) are set to ON, the synchronization signal that is originally as- signed, is used as it is (THRU). 10-16 HDS-7150/7100...

  • Page 145: Setting Of The Internal Generation Matte Signal

    [F6] (PERIPH) → [F2] (DME) The DME menu is displayed. PERPH (2) Press [F6] (DME INT) to select the desired DME. INT and EXT is switched by pressing [F6]. INT : built-in DME EXT : external DME equipment 10-17 HDS-7150/7100...

  • Page 146: Setting Of The Dme Interface

    (3) While pressing [F2] (DME1V), press the button of the AUX bus to which the DME VIDEO signal is assigned. (4) While pressing [F3] (DME1K), press the button of the AUX bus to which the DME KEY signal is assigned. 10-18 HDS-7150/7100...

  • Page 147: Setting Of The Gpi Input

    (4) Rotate knob 6 to display the action to start up by the trigger to the port selected at step (2). Each action is displayed on the [F6] screen by rotating knob 6. (5) Press [F5] (ACTION). The selected action is displayed on the [F5] screen. 10-19 HDS-7150/7100...

  • Page 148: Setting Of The Gpi Output

    This completes the settings needed to construct the system. For other set-ups, refer to the User’s Guide supplied with the HZS-7060. After all settings are completed, save the set-up data to nonvolatile memory. (Refer to “10-4. Saving Set-up Data to Nonvolatile Memory.”) 10-20 HDS-7150/7100...

  • Page 149: Saving Set-Up Data To Nonvolatile Memory

    This completes all the settings. Hereafter, when the main power is turned on, the set-up data saved in the nonvolatile memory is automatically invoked. If required, the set-up data can be saved in the optional memory pack (BZS-2090A). For details, refer to the User’s Guide supplied with the HZS-7060. 10-21 HDS-7150/7100...
  • Page 151 The material contained in this manual consists of information that is the property of Sony Corporation. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.
  • Page 152 HDS-7150 (SY, UCJ) Printed in Japan Sony Corporation HDS-7100 (SY, UCJ) E 2001. 9 16 B&P Company 3-203-096-04 ©1999...

This manual is also suitable for:

Hds-7100Hkds-7695Hkds-7695aBkds-7017Bkds-2010Bkdm-3010 ... Show all

Table of Contents