Advertisement
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
Refer to
instruction
manual
WARNING! DO NOT use the nail gun if damaged, has missing parts or is thought to be faulty. Contact your Service Agent.
WARNING! Never engage in horseplay with the tool.
WARNING! Always wear approved eye, face and hand protection when operating the nail gun. Wear a full face shield if stapling produces
metal filings or wood chips.
WARNING! Check correct air pressure is maintained and not exceeded. We recommend 60 to 100psi.
WARNING! Keep hands, face, feet and all parts of the body away from the firing head at all times.
DO NOT use the nail gun for a task it is not designed to perform.
DO NOT operate the nail gun near flammable substances or flammable containers.
DO NOT use the nail gun unless you have been instructed in its use by a qualified person.
DO NOT carry the nail gun by the air hose, or pull the hose from the air supply.
DO NOT operate the nail gun if you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT carry the nail gun with your hand on the power trigger in order to avoid unintentional firing.
DO NOT direct the nail gun or the air from the air hose at yourself or others.
DO NOT load bent or damaged staples into the magazine.
DO NOT overreach. Keep proper footing and balance at all times. Ensure the floor is not slippery and wear non-slip shoes.
DO NOT drive staples into thin boards or near the corners of the workpiece.
▲
DANGER! When putting the nail gun down, ensure that the trigger safety slide is not fouled, risking accidental firing.
Avoid unintentional firing. Keep fingers away from the trigger when not driving staples. Disconnect from the air supply especially
when loading staples,when carrying the tool, handing the tool to another person, leaving the work area, making adjustments to the tool,
clearing a jam or whenever it is left unattended.
Check the safety mechanism before use. Never use the stapler unless the safety is operating properly, otherwise the stapler could
drive a staple unexpectedly.
Place the tool properly on the workpiece. DO NOT drive staples one on top of another or with the tool at too steep an angle. The
staples could ricochet.
Keep the work area clean and well lit.
Keep people away from the work area.
Maintain the nail gun in good condition and replace any damaged or worn parts. Use genuine parts only. Unauthorised parts may
be dangerous and will invalidate the warranty.
Keep the air hose away from heat, oil and sharp edges. Check the air hose for wear before each use and ensure that all
connections are secure.
Follow all workshop safety rules, regulations, and conditions when using the nail gun.
Keep children and non essential persons away from the working area.
When not in use, disconnect from the air supply, remove the staples from the magazine and store cased in a safe, dry, childproof
location.
WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that
may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into
this product, but must be applied by the operator.
2. INTRODUCTION
Professional air stapler with lightweight aluminium body and rubber grip handle. Safety trigger device to prevent accidental firing of staples.
Supplied in carry-case with oiler and starter pack of staples.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . SA789.V2
Staple Capacity:. . . . . . . 13-32mm 18SWG
Maximum Pressure:.. . . . . . . . . . . . . 100psi
Air Inlet Size:. . . . . . . . . . . . . . . . . 1/4"BSP
Gun Weight: . . . . . . . . . . . . . . . . . . . 1.05kg
Noise Power: . . . . . . . . . . . . . . . . .95dB(A)
Noise Pressure: . . . . . . . . . . . . . . .82dB(A)
Vibration: . . . . . . . . . . . . . . . . . . . 3.05m/s²
Uncertainty: . . . . . . . . . . . . . . . . 1.525m/s²
© Jack Sealey Limited
INSTRUCTIONS FOR:
AIR STAPLE GUN 13-32
MODEL NO:
Wear ear
Wear eye
protection
protection
Original Language Version
MM
SA789.V2
Wear
protective
gloves
CAPACITY
SA789.V2 Issue: 1 - 27/02/15
Advertisement
Table of Contents
Related Manuals for Sealey SA789.V2
Summary of Contents for Sealey SA789.V2
- Page 1 Supplied in carry-case with oiler and starter pack of staples. 3. SPECIFICATION Model No: ....SA789.V2 Staple Capacity:..13-32mm 18SWG Maximum Pressure:..
-
Page 2: Operation
Snap the air hose onto the quick connector. Check for air leakage. If leakage is noted, stop using the tool immediately and seek repair by qualified personnel. 5.2.2. Be sure the air pressure gauge is operating properly and check it at least twice a day. Original Language Version SA789.V2 Issue: 1 - 27/02/15 © Jack Sealey Limited... - Page 3 Note: Always handle staples and their packaging carefully. If staples are dropped they may get damaged which will cause misfeeds and jamming. Original Language Version © Jack Sealey Limited SA789.V2 Issue1 - 27/02/15...
-
Page 4: Maintenance
6.1.4. Take care NOT to damage the driver plate, whilst using pliers or a screwdriver if required, to clear the jammed staple. 6.1.5. Put the nose plate (B) back on the nose (C), fastening it with screws (A). 6.1.6. Reconnect the air supply. 6.1.7. Reload the staples. fig.7 Original Language Version © Jack Sealey Limited SA789.V2 Issue: 1 - 27/02/15... -
Page 5: Troubleshooting
6.2.1. Lubricate the air tool daily with a high quality air tool oil (Sealey No. ATO/500 or ATO/1000) either via an oiler in the air supply system or by placing a few drops into the stapler air inlet immediately before use. -
Page 6: Personal Protective Equipment
WARNING! – Risk of Hand Arm Vibration Injury. This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately. This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC. This tool is to be operated in accordance with these instructions. Measured vibration emission value (a): .