Toro Reelmaster 01005 Operator's Manual
5, 7, and 11-blade reel mower
Hide thumbs
Also See for Reelmaster 01005:
- Operator's manual (21 pages) ,
- Operator's manual (16 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Toro Reelmaster 01005
Summary of Contents for Toro Reelmaster 01005
- Page 1 Form No. 3429-830 Rev A Reelmaster ® 5, 7, and 11-Blade Reel Mower Model No. 01005—Serial No. 403460001 and Up Model No. 01007—Serial No. 403460001 and Up Model No. 01011—Serial No. 403460001 and Up *3429-830* A Register at www.Toro.com. Original Instructions (EN)
- Page 2 Whenever you need service, genuine Toro parts, or Figure 1 additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model 1. Location of the model and serial numbers and serial numbers of your product ready.
-
Page 3: Table Of Contents
Safety Cutting Unit Safety..........3 Blade Safety ............4 Safety and Instructional Decals ......4 This machine has been designed in accordance with Setup ................ 5 EN ISO 5395 and ANSI B71.4–2017. Removing the Cutting Unit from the Carton ............. 5 Installing the Wheels .......... -
Page 4: Blade Safety
• Use only accessories, attachments, and servicing the blades. Only replace or sharpen the replacement parts approved by Toro. blades; never straighten or weld them. • On multi-bladed machines, take care as rotating 1 blade can cause other blades to rotate. -
Page 5: Setup
Setup Media and Additional Parts Description Qty. Operator's Manual Parts Catalog (not included)—refer to the Review the material and save it in an appropriate place. – included postcard for information on obtaining the Parts Catalog Note: Determine the left and right sides of the machine from the normal operating position. Product Overview Removing the Cutting Unit from the Carton... -
Page 6: Operation
Operation to two complete revolutions. Less than one revolution indicates heavy contact, which means the bedknife and reel must be readjusted for Note: Determine the left and right sides of the light contact; refer to steps 1, 3, and 4. machine from the normal operating position. -
Page 7: Adjusting The Height Of Cut
paper being cut or a slight drag when the paper Rotate the left pivot bolt to raise or lower the is pulled. bedbar. Insert a long strip of newspaper between the reel blade and the bedknife. While rotating the reel backward, turn the bedknife adjusting knob clockwise, one click at a time, until the paper is pinched lightly, which results in the paper being cut or a slight drag when the paper is pulled. -
Page 8: Operating Tips
Note: These are bench settings. The cutting stopped, repaired, and adjusted or severe damage unit will cut at a different height in turf because will result. of grass conditions and the weight of the cutting • Mowing Pattern—To prevent grass from lying unit. - Page 9 g026932 Figure 9 1. Nicked reel blades Noise – A cutting unit that has sharp cutting edges and is adjusted with light contact will emit a desirable whispering sound when the reel is spinning. By contrast, buzzing, clicking, or metallic sounds during operation indicate that the cutting unit is probably being operated with heavy contact between the bedknife and the reel.
-
Page 10: Maintenance
Maintenance Lubrication Greasing the Cutting Unit Each cutting unit has 4 grease fittings (Figure 11) that must be lubricated every 8 hours of operation with heavy duty No. 2 wheel bearing grease. g026926 Figure 12 1. 26 cm (10-1/4 inches) 2. -
Page 11: Checking The Fasteners And Reel Bearings
Install the inspection cover and the wheel. Grinding the Cutting Unit Note: For detailed sharpening information, refer to the Toro Manual for Sharpening Reel and Rotary Mowers, Form No. 09168SL. New and old bedknives should be ground attached to the bedbar; this ensures rigidity during grinding... -
Page 12: Lapping The Cutting Unit
After the reel and bedknife have been ground, perform the following adjustments: Set the height of cut. Adjust the bedknife to the reel. Note: As the reel blades continue to run against the bedknife a slight burr will appear on the front cutting edge surface the full length of the bedknife. -
Page 13: Replacing The Bedknife
3. Torque to 23 to 28 N∙m (200 to 250 in-lb). 2. Install and torque these first to 1 N∙m (10 in-lb). True the bedknife attached to the bedbar by grinding. Refer to the Toro Manual for Sharpening Reel and Rotary Mowers, Form No. 09168SL... -
Page 14: Adjusting The Reel, Roller, And Wheel Bearing
After the bedknife has been ground and is true, carefully slide the shaft through the right side adjust the reel, roller, and wheel bearing; refer to of the roller. Slide the roller shaft into the roller Adjusting the Reel, Roller, and Wheel Bearing until it penetrates the inner most oil seal on the (page 14). - Page 15 Notes:...
- Page 16 Notes:...
- Page 17 Notes:...
- Page 18 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 19 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact your Authorized Toro Service Center.