Advertisement
Quick Links
thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear
instruction
protective
manual
gloves
1. saFety
WarNINg! ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this storage
‰
system.
locate in a suitable work area.
9
Keep the work area clean, uncluttered and ensure there is adequate lighting.
9
WarNINg! Use storage on level and solid ground, preferably concrete.
‰
Keep the storage system clean and tidy in accordance with good workshop practice.
9
Keep children and unauthorised persons away from the work area.
9
Do Not use the storage system for any purpose other than that for which it is designed.
8
Do Not use the storage system outdoors.
8
Do Not place the storage system in a damp or wet location or an area where there is condensation.
8
Do Not clean the storage system with any solvents which may damage the surfaces or the protective coating.
8
8 8 Do Not move the storage system when there are items placed inside.
8 8
8 8 Do Not step on the shelves.
8 8
8 8 Do Not8overload the storage system.
8 8
2. INtroDuctIoN
Can be free standing or fixed to the wall. All ten units supplied on a single pallet. Hinged flat pack design makes this storage system easy and
quick to assemble. Base units fitted with stylish black MDF worktops and adjustable feet. Fitted with ball bearing drawer runners and magnetic
door latches. Pegboard design backing panels for additional storage. Extra units available to extend the storage system if required. Some simple
assembly required.
3. specIFIcatIoN
model no: .........................................................apms10HFp
Garage storage system 10pc
overall size: ........................................ 3100 x 460 x 2080mm
Inner drawer dimensions: ........................670 x 398 x 122mm
model no: ...........................................................apms2HFp
modular wall and base cabinet
model no: ........................................................ apms2HFpD
modular wall and base cabinet with drawer
model no: ........................................................ apms2HFps
modular stacking cabinet
© Jack Sealey limited
10pc garage storage system
apmsHFp serIes
model no:
Original Language Version
APMSHFP series | Issue 1 21/10/19
Advertisement
Related Manuals for Sealey APMSHFP Series
Summary of Contents for Sealey APMSHFP Series
- Page 1 IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 11x M6x16mm screws. top panel step 4: Insert 4 shelf supports inside the cabinet at the desired height. Place the shelf on the shelf supports. shelf support x4 shelf Original Language Version APMSHFP series | Issue 1 21/10/19 © Jack Sealey limited...
- Page 3 5: Insert four shelf supports inside the cabinet at the desired height. Place the shelf on the shelf supports. Note: The cabinet will only lock when the shelf is placed in the centre position. shelf support x4 Original Language Version APMSHFP series | Issue 1 21/10/19 © Jack Sealey limited...
- Page 4 4 top cabINet: Turn the cabinet over. Attach the bottom panel using 7x M6x16mm screws. m6x16mm screws x7 cabinet cabinet Original Language Version APMSHFP series | Issue 1 21/10/19 © Jack Sealey limited...
- Page 5 9: Insert 4x shelf supports inside the cabinet at the desired height. Place shelf on shelf supports. Note: the cabinet will only lock when the shelf is placed in the centre position. shelf shelf support Original Language Version APMSHFP series | Issue 1 21/10/19 © Jack Sealey limited...
- Page 6 Place one pegboard on the front, making sure the grommet hole is on the bottom. Attach using 2x M6x16mm screws per rail. pegboard rail x2 pegboard x1 m6x16mm screw x4 Original Language Version © Jack Sealey limited APMSHFP series | Issue 1 21/10/19...
- Page 7 M6x is on the top. Attach using 2x 16mm screws. M6x16mm screws per rail. m6x16mm screw x2 pegboard m6x16mm screw x4 Original Language Version © Jack Sealey limited APMSHFP series | Issue 1 21/10/19...
- Page 8 11: Push a stackable cabinet combination towards either side of the base cabinet/top cabinet combination. Insert a M6x16mm screw through the two interior end cover holes and secure with a M6 flange nut. m6x16mm screw x2 Original Language Version © Jack Sealey limited APMSHFP series | Issue 1 21/10/19...
-
Page 9: Environment Protection
Important: no liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey group, kempson Way, suffolk business park, bury st edmunds, suffolk. Ip32 7ar 01284 757500 01284 703534 sales@sealey.co.uk...