Advertisement
Quick Links
EU Light Kit
2015 and After Groundsmaster
Machine with Cab
Model No. 30640
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
Media and Additional Parts
Description
Installation instructions
Parts catalog
© 2014—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
Description
No parts required
No parts required
Column bracket assembly
Horn assembly
Column bracket mount
Carriage screw, 3/8 inch x 1 inch
Flange nut, 3/8 inch
Column cover
Screw
Right head light assembly
Left head light assembly
Flange head screw, 3/8 x 1 inch
Flange nut, 3/8 inch
Right headlight shield
Left headlight shield
Screw, 1/4 x 5/8 inch
Horn assembly
Screw, 5/16 x 3/4 inch
Flange head nut, 5/16 inch
Left rear lamp assembly
Right rear lamp assembly
Washer head screw, 3/8 x 3/4 inch
Grommet
Cable tie, 7–1/4 inch (184 mm)
Cable tie, 14–1/2 inch (368 mm)
No parts required
Register at www.Toro.com.
®
360 4-Wheel Drive Multi-Purpose
Qty.
–
–
1
1
1
2
2
1
2
1
1
4
4
1
1
8
1
1
1
1
1
4
1
13
2
–
Qty.
1
Use these instructions to install the kit.
1
Use this catalog to reference part numbers.
Form No. 3392-741 Rev A
Installation Instructions
Use
Prepare for installation.
Install the floor plate access hole.
Install the switch column assembly.
Install the head lights.
Install the horn.
Install the rear lamps.
Connect the wiring harness.
Finish the installation.
Use
Original Instructions (EN)
All Rights Reserved *3392-741* A
Printed in the USA.
Advertisement
Related Manuals for Toro 30640
Summary of Contents for Toro 30640
- Page 1 Form No. 3392-741 Rev A EU Light Kit 2015 and After Groundsmaster ® 360 4-Wheel Drive Multi-Purpose Machine with Cab Model No. 30640 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty.
- Page 2 Preparing for Installation No Parts Required Procedure 1. Park the machine on a level surface, stop the engine, engage the parking brake and remove the key from the G015806 ignition switch. Figure 2 2. Disconnect the negative (–) battery cable from the 1.
- Page 3 G015966 Figure 4 1. 1 inch (25 mm) 3. 1–5/8 inches (41 mm) Figure 5 2. 2 inch diameter (51 mm) 1. Screw (2) 5. Column bracket assembly 2. Column cover 6. Carriage screw 3. Flange nut 7. Horn button 4.
- Page 4 Figure 6 1. Headlight assembly 2. Headlight bracket 2. Repeat the procedure on the right side of the cab. Installing the Horn Parts needed for this procedure: Horn assembly Figure 7 Screw, 5/16 x 3/4 inch 1. Flange head nut 4.
- Page 5 Installing the Rear Lamps Parts needed for this procedure: Left rear lamp assembly Right rear lamp assembly Washer head screw, 3/8 x 3/4 inch Figure 9 Procedure 1. 2.25 inches (57 mm) 3. .350 inch diameter (9 mm) 1. Using the mounting holes to the rear of the hood 2.
- Page 6 • Cut a slit in the supplied grommet and cut out the bottom opening (Figure 10). With the cone end of the grommet facing down, wrap it around the harness and insert it into the knockout hole in the floor plate. •...
-
Page 7: Operation
Finishing the Installation No Parts Required Procedure 1. Pull up on the seat latch release bar and lower the seat into the locked position. 2. Attach the negative battery cable to the battery post. 3. Raise the hood until the prop rod can be raised above the frame tube, then lower the hood. - Page 8 Figure 15 1. Headlight adjusting screws...