Epson BrightLink Pro 1430Wi Installation Manual
Control pad and touch unit
Hide thumbs
Also See for BrightLink Pro 1430Wi:
- User manual (366 pages) ,
- Get started (6 pages) ,
- Installation manual (97 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Epson BrightLink Pro 1430Wi
Summary of Contents for Epson BrightLink Pro 1430Wi
- Page 1 Control Pad and Touch Unit Installation Guide...
-
Page 2: Safety Instructions
About This Installation Guide This guide describes how to install the Control Pad and Touch Unit (BrightLink® Pro 1430Wi) when using the ELPMB28 wall mount with the BrightLink Pro 1420Wi/1430Wi ultra-short-throw projectors. Safety Instructions For your safety, read all the instructions in this guide before using the wall mount. Incorrect handling that ignores instructions in this guide could damage the wall mount or could result in personal injury or property damage. -
Page 3: Installation Location
Viewing at close range could cause injury to eyesight. Connect the Touch Unit to the BrightLink Pro 1430Wi model only. Do not connect it to any other projectors or devices. Do not use the Touch Unit if you are using or near medical equipment such as a pacemaker. - Page 4 • When installing on a whiteboard, install the Touch Unit within the frame of the whiteboard. Correct position Incorrect position Make sure there are no obstacles, such as cables, or protruding objects such as whiteboard trays, pen holders, or thick frames in the shaded areas in the following figure. The Touch Unit will not operate correctly if anything is obstructing the infrared signal.
-
Page 5: Package Contents
1 Package Contents Touch Unit The following parts are packaged with your projector and are necessary when attaching the Touch Unit. When installing the Touch Unit on a non-magnetic surface, you will also need three M4 screws. Touch Unit and markers Spacer for screw hole (×3) (markers are inside the unit) Label (×4) -
Page 6: Specifications
2 Specifications Touch Unit External dimensions and weight The Touch Unit weighs approximately 16 oz (450 g). 8.3 in. (210 mm) 2.0 in. (51 mm) Attached labels The Touch Unit is a Class 1 laser product that conforms to the JIS C 6802:2011 standard. There are warning labels affixed to the Touch Unit to indicate that it is a Class 1 laser product. - Page 7 Control Pad External dimensions and weight The Control Pad weighs approximately 8.5 oz (240 g). 4.4 in. (111 mm) 5.4 in. (135.9 mm) 4.3 in. (109 mm) 0.4 in (11.5 mm) 0.1 in. (3.5 mm) Cable routing holes When routing cables through a wall, use the position ( ) in the following figure as the cable routing hole.
-
Page 8: Connecting Devices
Microphone Computer USB cable (for Easy Interactive Function) Document camera (Epson DC-06) Dedicated USB cable (supplied with document camera) For Interactive Use When interacting with a computer, you need a USB cable. However, when using the projector's built-in toolbar, you do not need a USB cable. - Page 9 Follow the steps below to install the Touch Unit and connect to the projector. Some menus may differ slightly from the illustrations, but the installation instructions are the same. Caution The Touch Unit should only be connected to the BrightLink Pro 1430Wi. Do not connect the Touch Unit to any other projectors or devices. Turn on the projector...
- Page 10 2. Select Touch Unit Setup. 3. Select Installation Pattern. The Installation pattern is displayed on the projected image. Remove the markers 1. Loosen the screw at the bottom of the dial cover.
- Page 11 2. Slide the dial cover down to remove it. 3. Remove the two markers from inside the Touch Unit. Use the markers to perform the angle adjustment (p. 14) after installing the Touch Unit. Determine the installation position for the Touch Unit Mark the following installation positions: •...
- Page 12 Install the Touch Unit • For magnetic screens, place the back of the Touch Unit on the screen surface to secure it. Caution When installing the Touch Unit on a magnetic surface, be careful not to trap your fingers or any other part of your body between the magnets and the installation surface.
-
Page 13: Connect The Cable
Connect the cable Connect the Touch Unit connection cable that is connected to the projector to the port on the Touch Unit. Adjust the angle Adjust the angle of the laser light coming from the Touch Unit so that the Touch Unit can detect the position of your fingers. - Page 14 2. Select Touch Unit Setup. 3. Select Power and set to On. The Touch Unit power turns on and the indicator light turns blue. Indicator light Warning Do not look into the projector’s projection window or the Touch Unit’s laser diffusion ports (located on the back of the Touch Unit);...
- Page 15 4. Select Angle Adjustment. The Angle Adjustment screen is displayed. 5. Turn the adjustment dials on the Touch Unit counterclockwise until you hear a click. Then, press the button on the remote control. When adjusting the dials, make sure to stop turning when you hear the click.
- Page 16 6. Attach the two markers you removed from the Touch Unit to the marker positions shown on the projected screen ( Green marker Blue marker position position Match the positions so that the crosses ( ) overlap with the points ( ) on the marker positions ).
- Page 17 Do not place anything other than the markers near the projected image during angle adjustment. If other objects are on the projected image, angle adjustment may not be performed correctly. 7. Turn the adjustment dials on the Touch Unit to move the pointers ( ) so that they move inside of the target ( ) of the same color (blue and green) on either side.
- Page 18 8. When the pointers on the left and right become solid colors ( ), press the button on the remote control. The following screen is displayed: 9. Place the markers at the top marker positions [1]. When angle adjustment is performed correctly, the upper pointers become solid colors ( ).
- Page 19 11. When you have finished checking the marker positions, remove the markers and press the button on the remote control. The following confirmation screen is displayed: 12. Trace the dots with your finger as shown. When angle adjustment is performed correctly, the traced dots disappear.
- Page 20 If the dots do not disappear even after attaching the infrared deflectors, turn the adjustment dials about a quarter turn counterclockwise. Next, press the button on the remote control, and then repeat step 12 again. If the dots do not disappear even after performing the above procedures, contact Epson.
-
Page 21: Attach Cover
14. Perform touch calibration by pressing Menu on the remote control. On the Extended menu, select Easy Interactive Function, then Touch Unit Setup. Select Touch Calibration and follow the instructions. Store the markers and attach labels 1. Store the markers inside the Touch Unit. 2. - Page 22 5 Installing the Control Pad You must install the control pad on the same surface as the projector, within the range specified in the installation instructions. You can use batteries to power the control pad, or the optional remote control cable set (model ELPKC28, part number V12H005C28).
-
Page 23: Remove The Cable Cover
Remove the cable cover Attach the Control Pad Attach the Control Pad with commercially available M4 × 20 mm screws (×4). Warning ❏ Make sure the screws are not angled. ❏ Make sure the Control Pad is firmly attached. ❏ Do not attach the Control Pad with double-side tape or magnets. -
Page 24: Install The Batteries
Install the batteries Caution Before handling the batteries, read the safety instructions in your projector’s online User’s Guide. ❏ Use two AA manganese or alkaline (recommended) batteries. Do not use any other type of battery. Rechargable batteries cannot be used. ❏... - Page 25 To perform the functions listed below, you will need to connect the appropriate cables: Projector function Required cables Projecting images from a USB flash drive USB cable 1 Saving data to a USB flash drive Supplying power from the projector Remote control cable set (model ELPKC28;...