Toro Z Master 8000 Series Setup Instructions
Riding mower with 42in or 48in/122cm cutting unit
Hide thumbs
Also See for Z Master 8000 Series:
- Operator's manual (68 pages) ,
- Installation instructions (2 pages) ,
- Setup instructions (12 pages)
Table of Contents
Advertisement
Quick Links
Z Master
with 42in or 48in/122cm Cutting Unit
Model No. 74310—Serial No. 316000001 and Up
Model No. 74311TE—Serial No. 316000001 and Up
Model No. 74312—Serial No. 316000001 and Up
Model No. 74313—Serial No. 316000001 and Up
Model No. 74315—Serial No. 400000000 and Up
This product contains a chemical or chemicals known to the State of California
The engine exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects, or other reproductive harm.
Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
7
8
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
8000 Series Riding Mower
Proposition 65 Warning
to cause cancer, birth defects, or reproductive harm.
Description
No parts required
Rear caster wheel
Bolt (1/2 x 13 inches)
Locknut (1/2 inch)
ROPS Kit (sold separately)
Long guard
Guard
Bolt (1/4 x 1 inch)
Flat washer (1/4 inch)
Retainer nut (1/4 inch)
No parts required
No parts required
No parts required
Wing nut (1/4 inch)
Register at www.Toro.com.
WARNING
CALIFORNIA
Qty.
–
1
1
1
1
1
1
4
4
4
–
–
–
2
Form No. 3420-439 Rev A
Setup Instructions
Use
Open the crate.
Remove the machine from the crate.
Install the ROPS (International
machines only).
Install the PTO-shaft guards
(International machines only).
Check the tire pressure.
Check the engine-oil level.
Check the torque of the wheel lug nuts.
Install the battery.
Original Instructions (EN)
All Rights Reserved *3420-439* A
Printed in the USA
Advertisement
Table of Contents
Related Manuals for Toro Z Master 8000 Series
Summary of Contents for Toro Z Master 8000 Series
- Page 1 – No parts required Check the torque of the wheel lug nuts. Wing nut (1/4 inch) Install the battery. © 2017—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3420-439* A 8111 Lyndale Avenue South Printed in the USA...
-
Page 2: Opening The Crate
Procedure Description Qty. – No parts required Charge the battery. – No parts required Check the hydraulic Fluid. No. 2 lithium grease (Purchase 1 tube Check the machine for grease. separately.) Check the machine before delivery to – No parts required the customer. - Page 3 CAUTION Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not support the machine or may malfunction, allowing the machine to fall and cause injury. Do not rely solely on mechanical g025175 or hydraulic jacks for support.
- Page 4 that the crate opening under the mower deck is With the deck-locking pins pulled out in the fully covered. unlock position, carefully lower the deck (Figure Place a plywood sheet (58.4 cm x 81.3 cm or 23 inches x 32 inches), or similar support, over the opening to provide support for the deck when you drive the machine off the crate (Figure...
- Page 5 Remove the rear caster-wheel assembly from inside the hopper. Remove the bolt holding the rear frame to the crate (Figure 11). Lift the front of the hopper up. Note: Use care when hoisting the machine to prevent damaging the hopper. Using the hoist, lift the machine at the location shown in Figure...
- Page 6 g025317 Figure 10 3. Place jack stands at the 1. Rear caster fork arrows 2. Bolt holding rear frame g026290 Figure 12 Remove and discard the rear-frame support and its hardware which is located behind the drive 1. Lift points on each side of the seat tires.
- Page 7 Installing the ROPS International Machines Only Parts needed for this procedure: ROPS Kit (sold separately) Procedure g025171 Figure 13 Install the ROPS Kit as described in the Installation 1. Deck-support pin 3. Side-strut hardware Instructions for the kit. 2. Strut between the deck-support pins With the deck-locking pins pulled out in the unlock position, carefully lower the deck...
-
Page 8: Checking The Tire Pressure
Checking the Tire Pressure No Parts Required Procedure Pressure: 103 kPa (15 psi) g036545 Figure 15 Note: Check the tire pressure before starting the 1. Bolts 2. Rubber guard machine. Refer to your Operator’s Manual for the correct tire type, correct air pressure needed, and procedure. -
Page 9: Installing The Battery
terminal first, then the negative (black) cable to the negative battery terminal. Slip the insulator boot over the positive terminal. Note: If time does not permit charging the battery, Installing the Battery or if charging equipment is not available, connect the negative battery cable and run the vehicle continuously for 20 to 30 minutes to sufficiently charge Parts needed for this procedure:... -
Page 10: Checking The Hydraulic Fluid
Remove the cap again and check the level of the fluid on the dipstick (Figure 18). Check the hydraulic reservoir and if necessary fill the reservoir to the appropriate level with Toro HYPR-OIL™ 500 hydraulic fluid. g026291 Figure 18 1. Full 2. - Page 11 Checking the Machine Before Delivery to the Customer No Parts Required Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures.
- Page 12 Delivering the Machine to the Customer Parts needed for this procedure: Operator's Manual Engine owner's manual Registration card Operator training material Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished.
- Page 13 Make sure that the customer receives the Operator's Manual, Engine Owner's Manual, Set Up Instructions, and operator training material. Make sure the customer knows the Parts Catalog is available at www.Toro.com. Assist the customer in loading the machine. Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provide below and keep a copy of this page for dealer records.
- Page 14 Notes:...
- Page 15 Notes:...