Page 1 Cisco ONS 15454 Hardware Installation Guide First Published: 2016-11-26 Last Modified: 2019-10-04 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883...
Page 3 Cisco ONS 15454 M2 Shelf Cisco ONS 15454 M6 Shelf C H A P T E R 2 Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf Important Safety Recommendations Required Tools and Equipment...
Page 4: Table Of Contents
ONS 15454 M6 Card Replacement NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves DLP-G676 Unpack and Verify the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves DLP-G677 Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves...
Page 5 Air Filter NTP-G8 Install the Fan-Tray Assembly ONS 15454 ANSI Alarm Expansion Panel NTP-G9 Install the Alarm Expansion Panel (ANSI Only) ONS 15454 ANSI Alarm, Timing, LAN, and Craft Pin Connections Alarm Contact Connections Timing Connections LAN Connections TL1 Craft Interface Installation...
Page 6 DLP-G35 Inspect the Shelf Installation and Connections DLP-G36 Measure Voltage NTP-G295 Connect the ONS 15454 Multishelf Node and Subtending Shelves to a Catalyst 2950 or Catalyst 3560 NTP-G296 Upgrade the ONS 15454 Multishelf with MS-ISC Card Configuration Using the Catalyst...
Page 7 Contents NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby) for a ONS 15454 Multishelf Node Ethernet Adapter Panel Filler and Blank Cards Cable Routing and Management Fiber Management Fiber Management Using the Patch-Panel Trays Standard and Deep Patch-Panel Trays (32-Channel)
Page 8 Contents NTP-G266 Install the ONS 15454 M2 Shelf DLP-G582 Mounting the 19-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration DLP-G583 Mounting the 23-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration DLP-G584 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2...
Page 9 DLP-G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only) DLP-G599 Turn On and Verify AC Office Power on the ONS 15454 M2 Shelf DLP-G600 Turn On and Verify DC Office Power on the ONS 15454 M2 Shelf...
Page 10 ANSI Rack Configuration DLP-G562 Mounting the Brackets on the ONS 15454 M6 Shelf for ETSI Rack Configuration DLP-G563 Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M6 Shelf for ETSI Rack Configuration DLP-G564 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf...
Page 11 DLP-G573 Connect Office Power (DC) to the ONS 15454 M6 Shelf (ETSI Only) DLP-G574 Turn On and Verify AC Office Power on the ONS 15454 M6 Shelf DLP-G575 Turn On and Verify DC Office Power on the ONS 15454 M6 Shelf...
Page 12 DLP-G654 Install the Cable Module DLP-G655 Route and Lock Cables NTP-G312 Attach Wires to Alarm, Timing, LAN, and Craft Pin Connections in Cisco ONS 15454 DLP-G295 Install Alarm Wires in ONS 15454 M6 DLP-G296 Install Timing Wires on ONS 15454 M6 - ANSI...
Page 13 NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf Assembly NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly NTP-G263 Replace the Air Filter of the AC Power Module in the ONS 15454 M6 Shelf Assembly NTP-G115 Clean Fiber Connectors...
Page 14 System Environmental Specifications Dimensions ONS 15454 M6 Shelf Specifications Bandwidth Configurations Cisco Transport Controller External LAN Interface for EMS TL1 Craft Interface Modem Interface Alarm Interface Passive Unit Remote Inventory BITS Interface System Timing Cisco ONS 15454 Hardware Installation Guide...
Page 15 Contents System Power AC Power Specifications DC Power Specifications Power Supply Modules Supported by ONS 15454 M6 ECU-S Power Calculation Fan Tray System Environmental Specifications Dimensions Cisco ONS 15454 Hardware Installation Guide...
Page 16 Contents Cisco ONS 15454 Hardware Installation Guide...
Page 17 Cisco ONS 15xxx products in a unidirectional path switched ring configuration. Rather, these terms, as well as “Path Protected Mesh Network” and “PPMN”, refer generally to Cisco's path protection feature, which may be used in any topological network configuration. Cisco does not recommend using its path protection feature in any particular topological network configuration.
Page 18 Shelf” and “Install the Cisco ONS 15454 M6 Shelf”. • Updated the AC fuse rating values for the ONS 15454 M2 and ONS 15454 M6 shelf assemblies in chapters, “Install the Cisco ONS 15454 M2 Shelf” and “Install the Cisco ONS 15454 M6 Shelf”.
Page 19 Connections in ONS 15454 M2” of chapter, “Install the Cisco ONS 15454 M2 Shelf”. June 2011 • Added the length of the SCSI cables in the chapter “Install the Cisco ONS 15454 M6 Shelf”. • Updated the procedure “DLP-G655 Lock Cables for a Clean Routing” to “DLP-G655 Route and Lock Cables”...
Page 20 Notes May 2012 • Updated the note in the section “Fan Tray Units for ONS 15454 Cards” in the chapter “Installing the ONS 15454 (ANSI and ETSI) Shelf”. • Updated the section “Fan-Tray Assembly” and the procedure “NTP-G268 Install the Fan-Tray Assembly in the ONS 15454 M2 Shelf”...
Page 21 • Updated the procedure “NTP-G331 Remove the Deep Door of the ONS 15454 M2 Shelf” in the chapter “Installing the ONS 15454 M2 Shelf”. • Added a note in the chapters, “Installing the ONS 15454 M2 Shelf” and “Installing the ONS 15454 M6 Shelf”.
Page 22 ONS 15454 M6 Shelf”. November 2016 Included R 10.6.1 features. March 2017 Added a note to "DLP-G298 Install LAN Wires in ONS 15454 M6" in the chapter, "Installing the ONS 15454 M6 Shelf". April 2017 Updated for R10.6.2 October 2019 Updated for R11.1...
Page 23 • Regulatory Compliance and Safety Information for Cisco ONS Products • Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms • Installing the GBIC, SFP, SFP+, QSFP, XFP, CXP, CFP, and CPAK Optical Modules in Cisco ONS Platforms •...
Page 24 Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsit laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännetty turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla. SÄILYTÄ NÄMÄ OHJEET Cisco ONS 15454 Hardware Installation Guide xxiv...
Page 25 Al final de cada advertencia encontrará el número que le ayudará a enc texto traducido en el apartado de traducciones que acompaña a este dispositivo. GUARDE ESTAS INSTRUCCIONES Cisco ONS 15454 Hardware Installation Guide...
Page 26 Använd det nummer som finns i slutet av varje varning för att dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco ONS 15454 Hardware Installation Guide xxvi...
Page 27 Brug erklæringsnummeret efter hver advarsel for at finde overs i de oversatte advarsler, der fulgte med denne enhed. Warning GEM DISSE ANVISNINGER Cisco ONS 15454 Hardware Installation Guide xxvii...
Page 28 Preface Preface Cisco ONS 15454 Hardware Installation Guide xxviii...
Page 29 This publication describes the international agency compliance and safety information for the Cisco ONS 15454, ONS 15454 M2, and ONS 15454 M6 system. It also includes translations of the safety warnings that appear in the Cisco ONS 15454 system documentation.
Page 30 Preface Obtaining Documentation, Obtaining Support, and Security Guidelines Cisco ONS 15454 Hardware Installation Guide...
Page 31 Cisco ONS 15454 M6 Shelf, on page 4 Compliance Standards Install the ONS 15454, ONS 15454 M2 and ONS 15454 M6 shelves in compliance with your local and national electrical codes: • United States: National Fire Protection Association (NFPA) 70; United States National Electrical Code.
Page 32 The ONS 15454 M2 shelf has 3 horizontal card slots —Slot 1, Slot 2, and Slot 3. While Slot 2 and Slot 3 house MSTP cards that provide 10 to 100 Gbps interconnections, Slot 1 accommodates the TNC, TNCE, TSC, TNCS-2, TNCS-2O, or TSCE card (timing and control card).
Page 33 You can mount the ONS 15454 M2 on a 19-inch or 23-inch ANSI rack (482.6 or 584.2 mm), or on a 600 x 600-mm (23.6 x 23.6-inch) or 600 x 300-mm (23.6 x 11.8-inch) ETSI standard equipment rack. The ONS 15454 M2 shelf can also be wall mounted or desktop mounted.
Page 34 M6 shelf provides improved fiber management. The ONS 15454 M6 is mounted on a 19-inch or 23-inch ANSI rack, or on a 600 x 600-mm or 600 x 300-mm ETSI standard equipment rack. The rack mounting is done using the mounting brackets or air deflectors. The air deflectors orient the air flow in a specific direction.
Page 35 Mid mount 185 mm It is mandatory that the correct type of 19-inch ANSI rack is chosen to mount the ONS 15454 M6 shelf. The recommended shape of the rack post is shown in Figure 1: 19-inch ANSI Rack Post Recommended for Cisco ONS 15454 M6 and M2 Shelves, on page 3.
Page 36 Overview Cisco ONS 15454 M6 Shelf Cisco ONS 15454 Hardware Installation Guide...
Page 37 Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf This chapter explains how to prepare for the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 shelf install. Note Unless otherwise specified, “ONS 15454”...
Page 38 A readily accessible two-poled disconnect device must be incorporated in the fixed wiring. Statement 1022 Note The ONS 15454, ONS 15454 M2 and ONS 15454 M6 are suitable for mounting on concrete or other noncombustible surfaces only. Note In this chapter, “shelf” refers to the steel enclosure that holds cards and connects power, and “node” refers to the entire hardware and software system.
Page 39 To avoid damage during shipment, either a standard front door or a temporary front door is preinstalled in the Cisco ONS 15454 M6 shelf. If a front door is ordered, a standard front door is preinstalled. If a front door is not ordered, a temporary front door is preinstalled.
Page 40 Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf Cisco Supplied Materials Cisco Supplied ONS 15454 ONS 15454 M2 ONS 15454 M6 Material ESD wrist strap ANSI ESD wrist strap (disposable) (1) ESD wrist strap (disposable) ESD wrist strap with 1.8 m (6 ft) coil cable...
Page 41 Tie wraps 0.125-inch (3.2 mm) W x 6.0-inch (152 mm) L (24) Caution Only use the power cables that are designed to be used with the ONS 15454 (ANSI or ETSI), the ONS 15454 M2 or ONS 15454 M6. These are sold separately. User Supplied Materials The following materials, tools, and equipment are required but are not supplied with the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6.
Page 42 Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf User Supplied Materials Table 2: User Supplied Materials User ONS 15454 ONS 15454 M2 ONS 15454 M6 Supplied Material Bit error ANSI rate (BER)
Page 43 Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf User Supplied Materials User ONS 15454 ONS 15454 M2 ONS 15454 M6 Supplied Material ETSI • Copper ground cable 13.3-mm² (#6 AWG) stranded, specified for up to...
Page 44 Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf User Supplied Materials User ONS 15454 ONS 15454 M2 ONS 15454 M6 Supplied Material Power Optical power meter (for use with Optical power meter (for use...
Page 45 Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf Ordering Solutions for ONS 15454 M2 and ONS 15454 M6 User ONS 15454 ONS 15454 M2 ONS 15454 M6 Supplied Material Wire Wire wrapper...
Page 46 Preparing to Install the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf ONS 15454 Figure 3: Installing Cards in the ONS 15454 ANSI The following figure shows card installation in the ONS 15454 ETSI shelf.
Page 47 Figure 4: Installing Cards in the ONS 15454 ETSI Shelf The ONS 15454 shelf assemblies have 17 card slots numbered sequentially from left to right. Slots 7 and 11 are dedicated to TCC2/TCC2P/TCC3 cards. Slot 9 is reserved for the optional AIC-I card.
Page 48 The ONS 15454 M2 shelf must be equipped with a TNC, TNCE, TSC, TNCS-2, TNCS-2O, or TSCE card. Shelf slots have symbols indicating the type of cards that you can install in them. Each ONS 15454 M2 card has a corresponding symbol. The symbol on the card must match the symbol on the slot.
Page 49: Ons 15454 M6
7 are dedicated for common line cards. Caution The ONS 15454 M6 system can work with a single control card (TNC, TNCE, TSC, TNCS-2, TNCS-2O, or TSCE). The TNC, TNCE, TSC, TNCS-2, TNCS-2O, and TSCE cards cannot operate in a shelf at the same time.
Page 50: Ntp-G305 Unpack And Inspect The Ons 15454, Ons 15454 M2, And Ons 15454 M6 Shelves
If the active card needs to be replaced, switch it to standby prior to removing the card from the node. For traffic switching procedures, refer to the Cisco ONS 15454 DWDM Configuration Guide.
Page 51: Dlp-G677 Inspect The Ons 15454, Ons 15454 M2, And Ons 15454 M6 Shelves
The Cisco Systems logo designates the top of the box. Step 2 Remove the foam inserts from the box. The box contains the ONS 15454 shelf (wrapped in plastic) and a smaller box of items needed for installation.
Page 52 DLP-G677 Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves • The frame is not bent. Step 3 If the pins are bent or broken, or the frame is bent, call your Cisco sales engineer for a replacement. Step 4 (ONS 15454 only) Close the front door before installing.
Page 53: Installing The Ons 15454 M12 (Ansi And Etsi) Shelf
The TCC2P card can be used as a control card in a subtended shelf where the node controller is TCC3 card on ONS 15454 chassis or TNC/TNCE/TNCS/TNCS-O cards on ONS 15454 M6 or NCS 20015 chassis. The TCC2P card can also be used as a node controller in a stand-alone configuration.
Page 54: Ons 15454 Ansi Rack Installation
(25.4 mm) of airspace below the installed shelf to allow air flow to the fan intake. If a second ONS 15454 ANSI is installed underneath the shelf, the air ramp on top of the lower shelf provides the air spacing needed and should not be modified in any way.
Page 55: Reversible Mounting Bracket
Caution When mounting the ONS 15454 ANSI shelf in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 ANSI shipping kit, or remove the coating from the threads to ensure electrical continuity.
Page 56: Mounting A Single Node
ONS 15454 ANSI shelves and a fuse and alarm panel. However, unequal flange racks are limited to three ONS 15454 ANSI shelves and a fuse and alarm panel, or four ONS 15454 ANSI shelves using a fuse and alarm panel from an adjacent rack.
Page 57: Ons 15454 Etsi Rack Installation
The ONS 15454 ETSI must have one inch (25.4 mm) of airspace below the installed shelf to allow air flow to the fan intake. If a second ONS 15454 ETSI is installed below the first shelf, an ETSI air ramp unit must be assembled between the two shelves to ensure adequate air flow.
Page 58: Mounting A Single Node
The ONS 15454 ETSI requires 616.5 mm (24.24 inch) minimum of vertical rack space and 25 mm (1 inch) below the installed shelf to allow air flow to the fan intake. If a second ONS 15454 ETSI is installed above a shelf, the air ramp between the shelves provides space for air flow.
Page 59: Mounting Multiple Nodes
Mounting Multiple Nodes Most standard (Telcordia GR-63-CORE, 23-inch [584.2 mm]) seven-foot (2,133 mm) racks can hold three ONS 15454 ETSI shelves, two air ramps, and a fuse and alarm panel. The following figure shows a three-shelf ONS 15454 ETSI bay assembly.
Page 60 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Mounting Multiple Nodes Figure 11: Three-Shelf ONS 15454 ETSI Bay Assembly Warning Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the floor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip over.
Page 61: Ntp-G306 Install The Ons 15454 Shelf
Warning The ONS 15454 must have 1 inch (25.4 mm) of airspace below the installed shelf assembly to allow air flow to the fan intake. The air ramp (the angled piece of sheet metal on top of the shelf assembly) provides this spacing and should not be modified in any way.
Page 62 Step 3 Complete the necessary rack mount task as applicable: • DLP-G678 Mount the ONS 15454 Shelf in a Rack (One Person), on page 36 • DLP-G679 Mount the ONS 15454 Shelf in a Rack (Two People), on page 37 •...
Page 63: Dlp-G3 Reverse The Mounting Bracket To Fit A 19-Inch (482.6-Mm) Rack (Ansi Only)
Caution When mounting the ONS 15454 in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 ANSI ship kit, or remove the coating from the threads to ensure electrical continuity.
Page 64: Dlp-G4 Install The External Brackets And Air Filter (Ansi Only)
Installing the external brackets and air filter on the bottom of the shelf enables access to the air filter without removing the fan-tray assembly. This task applies to the ONS 15454 ANSI shelf only. #2 Phillips Dynamometric screwdriver...
Page 65 Caution Although the air filter can work with older fan-trays if it is installed with either side facing up, Cisco recommends that you install it with the metal bracing facing up to preserve the surface of the filter. You must install the air filter with the metal bracing facing up with 15454-CC-FTA.
Page 66: Dlp-G678 Mount The Ons 15454 Shelf In A Rack (One Person)
The ONS 15454 ETSI requires 616.5 mm (24.24 inch) minimum of vertical rack space and 25 mm (1 inch) below the installed shelf to allow air flow to the fan intake. If a second ONS 15454 ETSI is installed above a shelf, the air ramp between the shelves provides space for air flow.
Page 67: Dlp-G679 Mount The Ons 15454 Shelf In A Rack (Two People)
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G679 Mount the ONS 15454 Shelf in a Rack (Two People) Figure 14: Mounting an ONS 15454 ETSI in a Rack Step 3 Using the hex tool that shipped with the assembly, install the two temporary set screws into the holes that will not be used to mount the shelf.
Page 68 The ONS 15454 ANSI must have one inch (25.4 mm) of airspace below the installed shelf to allow air flow to the fan intake. If a second ONS 15454 is installed underneath a shelf, the air ramp on top of the bottom shelf provides the desired space.
Page 69: Dlp-G680 Mount Multiple Ons 15454 Shelf Assemblies In A Rack
Note A standard ETSI rack can hold three ONS 15454 ETSI shelf assemblies and two air ramps. When mounting a shelf in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.
Page 70 The ONS 15454 ANSI must have one inch (25.4 mm) of airspace below the installed shelf to allow air flow to the fan intake. If a second ONS 15454 is installed underneath a shelf, the air ramp on top of the bottom shelf provides the desired space.
Page 71 The air ramp is needed if you install more than one ONS 15454 ETSI shelf in a rack. To ensure that the air ramp is secure, use one or two M6 mounting screws for each side of the shelf. The following figure shows how to mount an air ramp in the rack.
Page 72: Dlp-G8 Install The Air Ramp
Repeat this task for every shelf you need to install. Step 5 Return to your originating procedure (NTP). DLP-G8 Install the Air Ramp Purpose Use this task to install the air ramp for standard and deep door ONS 15454 Tools/Equipment #2 Phillips Dynamometric screwdriver Prerequisite Procedures None...
Page 73 Figure 17: Air Ramp with Brackets in an ETSI Configuration Step 5 To install the 19-inch and 23-inch brackets on an ONS 15454 ANSI, with standard door and spool, remove the screws that attach the mounting bracket to the side of the shelf.
Page 74 Figure 18: Positioning 19 or 23 Reversible Brackets on ONS 15454 ANSI with STD Door and Spool Step 8 To install the 19-inch and 23-inch brackets in an ONS 15454 ANSI deep door, remove the screws that attach the mounting bracket to the side of the shelf.
Page 75: Front Door
ONS 15454 shelf. These LEDs must be visible so that technicians can quickly determine if any alarms are present on the ONS 15454 shelf or the network. You can use the LCD to further isolate alarms.
Page 76 Figure 20: The ONS 15454 Front Door The ONS 15454 ANSI ships with a standard door but can also accommodate a deep door and extended fiber clips (15454-DOOR-KIT) to provide additional room for cabling as shown in the following figure. The ONS 15454 ETSI does not support the deep door.
Page 77 Figure 21: Cisco ONS 15454 ANSI Deep Door The ONS 15454 door locks with a pinned hex key that ships with the shelf. A button on the right side of the shelf releases the door. You can remove the front door to provide unrestricted access to the front of the shelf.
Page 78 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Front Door Figure 22: ONS 15454 ANSI Front Door Ground Strap The following figure shows how to remove the ONS 15454 ANSI front door. Cisco ONS 15454 Hardware Installation Guide...
Page 79 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Front Door Figure 23: Removing the ONS 15454 ANSI Front Door The following figure shows how to remove the ONS 15454 ETSI front door. Cisco ONS 15454 Hardware Installation Guide...
Page 80 An erasable label is pasted on the inside of the front door. You can use the label to record slot assignments, port assignments, card types, node ID, rack ID, and serial number for the ONS 15454. The following figure shows the erasable label on the ONS 15454 ANSI shelf.
Page 81 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Front Door Figure 25: ONS 15454 ANSI Front-Door Erasable Label The following figure shows the erasable label on the ONS 15454 ETSI shelf. Cisco ONS 15454 Hardware Installation Guide...
Page 82 The front door label also includes the Class I and Class 1M laser warning. The following figure shows the ONS 15454 ANSI laser warning. Figure 27: Laser Warning on the ONS 15454 ANSI Front-Door Label The following figure shows the ONS 15454 ETSI laser warning.
Page 83: Ons 15454 Ansi Backplane Covers
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf ONS 15454 ANSI Backplane Covers Figure 28: Laser Warning on the ONS 15454 ETSI Front-Door Label ONS 15454 ANSI Backplane Covers If a backplane does not have an electrical interface assembly (EIA) panel installed, it should have two sheet metal backplane covers (one on each side of the backplane).
Page 84: Lower Backplane Cover
Figure 29: Backplane Covers Lower Backplane Cover The lower section of the ONS 15454 ANSI backplane is covered by either a clear plastic protector (15454-SA-ANSI) or a sheet metal cover (15454-SA-HD), which is held in place by five 6-32 x 1/2 inch screws.
Page 85 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Rear Cover Figure 31: Backplane Attachment for Cover You can also install the optional spacers if more space is needed between the cables and rear cover as shown in the following figure.
Page 86: Alarm Interface Panel
The AIP is located above the alarm contacts on the lower section of the backplane. The AIP provides surge protection for the ONS 15454 ANSI. It also provides an interface from the backplane to the fan-tray assembly and LCD. The AIP plugs into the backplane using a 96-pin DIN connector and is held in place with two retaining screws.
Page 87: Dlp-G9 Open The Front Cabinet Compartment (Door)
Note The ONS 15454 shelf has an ESD plug input and is shipped with an ESD wrist strap. The ESD plug input is located on the outside of the shelf on the right side. It is labeled “ESD” on the top and bottom. Always wear an ESD wrist strap and connect the strap to the ESD plug when working on the ONS 15454.
Page 88: Dlp-G10 Remove The Front Door
Open the front door lock. The ONS 15454 shelf comes with a pinned hex key for locking and unlocking the front door. Turn the key counterclockwise to unlock the door and clockwise to lock it. The following figure illustrates the front door of the ANSI shelf.
Page 89 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G10 Remove the Front Door Required/As Needed As needed Onsite/Remote Onsite Security Level None Procedure Step 1 For ONS 15454 ETSI shelves: a) Unscrew the nut holding the ground wire to the shelf. Remove the nut and washer.
Page 90: Ntp-G4 Open And Remove The Fmec Cover (Etsi Only)
NTP-G4 Open and Remove the FMEC Cover (ETSI Only) Purpose This procedure opens and removes the FMEC cover on the ONS 15454 ETSI. The ONS 15454 ETSI has a screw-in panel over the EFCA. The FMEC cover protects the FMEC cards. Medium slot-head screwdriver...
Page 91: Dlp-G11 Open The Fmec Cover
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G11 Open the FMEC Cover Procedure Step 1 Complete the DLP-G11 Open the FMEC Cover , on page Step 2 Complete the DLP-G12 Remove the FMEC Cover , on page Step 3...
Page 92: Dlp-G12 Remove The Fmec Cover
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G12 Remove the FMEC Cover Figure 36: Unscrewing the FMEC Cover Step 2 Use the handles to pull the cover forward. Step 3 Return to your originating procedure (NTP). DLP-G12 Remove the FMEC Cover...
Page 93: Ntp-G5 Remove The Backplane Covers (Ansi Only)
NTP-G5 Remove the Backplane Covers (ANSI Only) Purpose This procedure describes how to access the ONS 15454 ANSI backplane by removing the covers. The backplane has two sheet metal covers (one on either side) and a lower backplane cover at the bottom.
Page 94: Dlp-G13 Remove The Lower Backplane Cover
NTP-G7 Install the Power and Ground , on page Stop. You have completed this procedure. DLP-G13 Remove the Lower Backplane Cover Purpose This task removes the lower backplane cover of the ONS 15454 ANSI shelf. #2 Phillips Dynamometric screwdriver Tools/Equipment Medium slot-head screwdriver...
Page 95: Dlp-G14 Remove The Backplane Sheet Metal Cover
The ONS 15454 ETSI EFCA at the top of the shelf has 12 FMEC slots numbered sequentially from left to right (18 to 29). Slots 18 to 22 and 25 to 29 provide electrical connections. Slots 23 and 24 host the MIC-A/P and MIC-C/T/P cards, respectively.
Page 96: Ntp-G6 Install The Mic-A/P And Mic-T/C/P Fmecs (Etsi Only)
Cisco CPT and Cisco ONS Platforms Note The ONS 15454 ETSI EFCA has 12 FMEC slots numbered sequentially from left to right beginning with Slot 18. Slots 18 to 22 and 25 to 29 provide electrical connections for the corresponding slots, so they are unnecessary in DWDM applications.
Page 97: Power And Ground Description
Slide the FMEC along the guide rails into the desired FMEC slot or slots. Step 4 Push the FMEC gently into the connector. The ONS 15454 ETSI FMECs plug into electrical connectors on the back panel of the shelf when the screws are tightened. The following figure shows FMEC installation.
Page 98: Ntp-G7 Install The Power And Ground
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G7 Install the Power and Ground NTP-G7 Install the Power and Ground Purpose This procedure installs power feeds and grounds the ONS 15454. Tools/Equipment ANSI and ETSI: • #2 Phillips Dynamometric screwdriver •...
Page 99 Statement 1028 Caution Always use the supplied ESD wristband when working with a powered ONS 15454. For detailed instructions on how to wear the ESD wristband, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT...
Page 100: Dlp-G17 Connect Office Power To The Ons 15454 Etsi
When installing or replacing the unit, the ground connection must always be made first and disconnected last. Statement 1046 Caution Do not apply power to the ONS 15454 ETSI until you complete all installation steps and check the continuity of the –48 VDC battery and battery return. Note No more than 2 m (7 ft) of the power supply cable should be exposed between the equipment and the fiber-storage tray.
Page 101: Dlp-G18 Connect Office Power To The Ons 15454 Ansi
Note If the system loses power or if both TCC2/TCC2P/TCC3 cards are reset, you must reset the ONS 15454 ETSI clock. After powering down, the date defaults to January 1, 1970, 00:04:15. To reset the clock, see the “Turn Up a Node”...
Page 102 ONS 15454 clock. After powering down, the date defaults to January 1, 1970, 00:04:15. To reset the clock, see the “Turn Up a Node” chapter in the Cisco ONS 15454 DWDM Configuration Guide. If you are using the TCC2/TCC2P/TCC3 cards, the system clock will run for up to three hours. In this case, no action would be required.
Page 103 Figure 40: Cisco ONS 15454 Power Terminals Step 4 Remove or loosen the #8 power terminal screws on the ONS 15454. To avoid confusion, label the cables connected to the BAT1/RET1 (A) power terminals as 1 and the cables connected to the BAT2/RET2 (B) power terminals as 2.
Page 104: Dlp-G19 Turn On And Verify Office Power
DLP-G19 Turn On and Verify Office Power Step 9 If you use redundant power leads, terminate the return 2 lead to the positive RET2 terminal on the ONS 15454. Terminate the negative 2 lead to the negative BAT2 terminal on the ONS 15454. Use oxidation-preventative grease to keep connections noncorrosive.
Page 105: Shelf Voltage And Temperature
The temperature measured by the TCC2/TCC2P/TCC3 sensors appears on the LCD screen in the ONS 15454 chassis. The input voltages and temperature of the ONS 15454 chassis are displayed in the Shelf view > Provisioning > General > Voltage/Temperature pane in CTC. The voltage supplied to the shelf (in millivolts) is displayed in the Voltage area of the Voltage/Temperature pane.
Page 106: Ntp-G230 View Shelf Voltage And Temperature
The fan-tray assembly is located at the bottom of the ONS 15454 shelf. The fan-tray is a removable drawer that holds fans and fan-control circuitry for the ONS 15454. The front door can be left in place or removed before installing the fan-tray assembly. After you install the fan-tray, you should only need to access it if a fan failure occurs or if you need to replace or clean the fan-tray air filter.
Page 107 Figure 41: Position of the ONS 15454 ETSI Fan-Tray Assembly, on page shows the position of the ONS 15454 ETSI fan-tray assembly. (The fan-tray assembly on the ONS 15454 ANSI is located in a similar position.) Caution Do not operate an ONS 15454 without the mandatory fan-tray air filter.
Page 108: Fan-Tray Units For Ons 15454 Cards
Figure 41: Position of the ONS 15454 ETSI Fan-Tray Assembly Fan-tray Units for ONS 15454 Cards The following table lists the applicable fan-tray units supported for ONS 15454 cards: Table 7: Fan-tray Units for ONS 15454 Cards ONS 15454 Cards...
Page 109 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Fan-tray Units for ONS 15454 Cards ONS 15454 Cards 15454E-FTA-48V (ETSI shelf)/ 15454E-CC-FTA (ETSI shelf)/ 15454-FTA3-T (ANSI shelf) 15454-CC-FTA (ANSI shelf) OSCM OSC-CSM OPT-PRE OPT-BST OPT-BST-E OPT-BST-L OPT-AMP-L OPT-AMP-17-C OPT-AMP-C OPT-RAMP-C...
Page 110 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Fan-tray Units for ONS 15454 Cards ONS 15454 Cards 15454E-FTA-48V (ETSI shelf)/ 15454E-CC-FTA (ETSI shelf)/ 15454-FTA3-T (ANSI shelf) 15454-CC-FTA (ANSI shelf) 40-DMX-C 40-DMX-CE 40-MUX-C 40-WSS-C 40-WSS-CE 40-WXC-C 40-SMR1-C/40-SMR2-C 80-WXC-C TXP_MR_10G TXP_MR_2.5G TXPP_MR_2.5G...
Page 111: Fan Speed
ONS 15454 M2 fan-tray assembly, see the Fan-Tray Assembly, on page 234. The 15454-M6-FTA and 15454-M6-FTA2 are installed in the ONS 15454-M6 shelf assembly. For information on the ONS 15454 M6 fan-tray assembly, see the Fan-Tray Assembly , on page 387.
Page 112: Air Filter
The reusable filter is made of a gray, open-cell, polyurethane foam that is specially coated to provide fire and fungi resistance. All versions of the ONS 15454 can use the reusable air filter. Spare filters should be kept in stock. Inspect the air filter every 30 days, and clean the filter every three to six months. Replace the air filter every two to three years.
Page 113 ONS 15454 ANSI, on page 85 shows the fan-tray assembly location on the ONS 15454 ANSI. • For the ONS 15454 ETSI shelf, press and hold the locks on the outer edges as you slide the fan-tray assembly into the shelf.
Page 114 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G8 Install the Fan-Tray Assembly • For the ONS 15454 ANSI shelf, press and hold the locks on the outer edges as you slide the fan-tray assembly into the shelf. The electrical plug at the rear of the tray should plug into the corresponding receptacle on the assembly.
Page 115: Ons 15454 Ansi Alarm Expansion Panel
The optional ONS 15454 ANSI alarm expansion panel (AEP) can be used with the AIC-I card to provide an additional 48 dry alarm contacts for the ONS 15454 ANSI: 32 inputs and 16 outputs. The AEP is a printed circuit board assembly that is installed on the backplane. The following figure shows the AEP board; the left connector is the input connector and the right connector is the output connector.
Page 116 60 VDC, and a maximum current of 100 mA. See the “External Alarms and Controls” section of the “Install the Control Cards” chapter in the Cisco ONS 15454 DWDM Configuration Guide for further information. The following figure shows the wire-wrapping connections on the shelf backplane used to connect to the AEP.
Page 117 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf ONS 15454 ANSI Alarm Expansion Panel Figure 46: AEP Wire-Wrap Connections to Backplane Pins The following table shows the backplane pin assignments and corresponding signals on the AIC-I and AEP. Table 8: Pin Assignments for the AEP...
Page 118 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf ONS 15454 ANSI Alarm Expansion Panel Figure 47: Alarm Input Circuit Diagram The following table lists the connections to the external alarm sources. Table 9: Alarm Input Pin Association AMP Champ Pin Number...
Page 119 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf ONS 15454 ANSI Alarm Expansion Panel AMP Champ Pin Number Signal Name AMP Champ Pin Number Signal Name ALARM_IN_21– ALARM_IN_22– ALARM_IN_23– ALARM_IN_24– ALARM_IN_25– ALARM_IN_26– ALARM_IN_27– ALARM_IN_28– ALARM_IN_29– ALARM_IN_30– ALARM_IN_31– — ALARM_IN_+ GND1 ALARM_IN_0–...
Page 120 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf ONS 15454 ANSI Alarm Expansion Panel AMP Champ Pin Number Signal Name AMP Champ Pin Number Signal Name COM_1 — NO_1 NO_2 — COM_2 COM_3 — NO_3 NO_4 — COM_4 COM_5 —...
Page 121: Ntp-G9 Install The Alarm Expansion Panel (Ansi Only)
16 provided by the AIC-I card. Typically, the AEP is preinstalled when ordered with the ONS 15454 ANSI; however, the AEP can be ordered separately. The AIC-I card must be installed before you can provision the alarm contacts enabled by the AEP.
Page 122 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G9 Install the Alarm Expansion Panel (ANSI Only) Figure 49: Replace Backplane Screws with Standoffs Step 2 Attach the remaining two standoffs on either side of the backplane as shown in the following figure.
Page 123 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G9 Install the Alarm Expansion Panel (ANSI Only) Figure 50: Installing Standoffs and the AEP Step 4 Insert and tighten three screws to secure the AEP to the backplane. Step 5 Connect the AEP cable to the backplane and AEP: a) Connect the 10 colored wires to the wire-wrap pins on the backplane.
Page 124: Ons 15454 Ansi Alarm, Timing, Lan, And Craft Pin Connections
Stop. You have completed this procedure. ONS 15454 ANSI Alarm, Timing, LAN, and Craft Pin Connections Pin connections are provided on the ONS 15454 ANSI backplane. For information about ONS 15454 ETSI connections, see the ONS 15454 ETSI Front Mount Electrical Connection, on page...
Page 125 ONS 15454 ANSI Alarm, Timing, LAN, and Craft Pin Connections The ONS 15454 ANSI has a backplane pin field located at the bottom of the backplane. The backplane pin field provides 0.045 inch2 (29 mm2) wire-wrap pins for enabling external alarms, timing input and output, and craft interface terminals.
Page 126 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf ONS 15454 ANSI Alarm, Timing, LAN, and Craft Pin Connections Figure 52: Cisco ONS 15454 Backplane Pinouts (Release 3.4 or Later) Cisco ONS 15454 Hardware Installation Guide...
Page 127: Alarm Contact Connections
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Alarm Contact Connections Figure 53: ONS 15454 ANSI Backplane Pinouts Alarm Contact Connections The alarm pin field supports up to 17 alarm contacts, including four audible alarms, four visual alarms, one alarm cutoff (ACO), and four user-definable alarm input and output contacts.
Page 128: Timing Connections
LAN Connections Use the LAN pins on the ONS 15454 ANSI backplane to connect the ONS 15454 ANSI to a workstation or Ethernet LAN, or to a LAN modem for remote access to the node. You can also use the LAN port on the TCC2/TCC2P/TCC3 faceplate to connect a workstation or to connect the ONS 15454 ANSI to the network.
Page 129: Tl1 Craft Interface Installation
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf TL1 Craft Interface Installation Before you can connect an ONS 15454 ANSI to other ONS 15454 ANSI shelves or to a LAN, you must change the default IP address that is shipped with each ONS 15454 ANSI (192.1.0.2).
Page 130: Ntp-G10 Attach Wires To Alarm, Timing, Lan, And Craft Pin Connections
Security Level None Caution Always use the supplied ESD wristband when working with a powered ONS 15454 ETSI. For detailed instructions on how to wear the ESD wristband, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.
Page 131: Dlp-G20 Install Alarm Wires On The Mic-A/P (Etsi Only)
Stop. You have completed this procedure. DLP-G20 Install Alarm Wires on the MIC-A/P (ETSI Only) This task installs alarm cables on the MIC-A/P on the ONS 15454 ETSI so that Purpose you can provision external (environmental) alarms and controls with the AIC-I card.
Page 132 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G20 Install Alarm Wires on the MIC-A/P (ETSI Only) DB-62 Pin Connector Signal Name Function ALMINP1+ Alarm input pair number 2 ALMINP2– Alarm input pair number 3 ALMINP2+ Alarm input pair number 3 ALMINP3–...
Page 133 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G20 Install Alarm Wires on the MIC-A/P (ETSI Only) DB-62 Pin Connector Signal Name Function EXALM10+ Extra alarm 10 EXALM11– Extra alarm 11 EXALM11+ Extra alarm 11 ALMOUP0– Normally open output pair number 1...
Page 134: Dlp-G21 Install Timing Wires On The Mic-C/T/P (Etsi Only)
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G21 Install Timing Wires on the MIC-C/T/P (ETSI Only) DB-62 Pin Connector Signal Name Function VISALM3+ Normally open minor visible alarm Step 2 Connect the other end of the alarm and control wires according to local site practice.
Page 135: Dlp-G22 Install Lan Wires On The Mic-C/T/P (Etsi Only)
Return to your originating procedure (NTP). DLP-G22 Install LAN Wires on the MIC-C/T/P (ETSI Only) Purpose This task installs the LAN wires on the ONS 15454 ETSI MIC-C/T/P. Standard CAT-5 Ethernet cable (straight-through for data terminating equipment Tools/Equipment [DTE] or cross-over for data circuit-terminating equipment [DCE])
Page 136: Dlp-G23 Install Alarm Wires On The Backplane (Ansi Only)
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G23 Install Alarm Wires on the Backplane (ANSI Only) Table 17: LAN Pin Assignments RJ-45 Pin RJ-45 Pin Function LAN 1 Connecting to PNMSRX+white/green (a hub or PNMSRX–green switch)Cross-over Ethernet cable PNMSTXwhite/orange —...
Page 137 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G23 Install Alarm Wires on the Backplane (ANSI Only) Required/As Needed As needed Onsite/Remote Onsite Security Level None Procedure Step 1 Using 100-ohm shielded BITS clock cable pair #22 or #24 AWG (0.51 mm² or 0.64 mm²) twisted-pair T1-type wires, wrap the alarm wires on the appropriate wire-wrap pins according to local site practice.
Page 138 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G23 Install Alarm Wires on the Backplane (ANSI Only) Figure 54: Cisco ONS 15454 Backplane Pinouts (Release 3.4 or Later) Cisco ONS 15454 Hardware Installation Guide...
Page 139: Dlp-G24 Install Timing Wires On The Backplane (Ansi Only)
Return to your originating procedure (NTP). DLP-G24 Install Timing Wires on the Backplane (ANSI Only) Purpose This task installs the BITS timing wires on the ONS 15454 ANSI backplane. Tools/Equipment Wire wrapper 100-ohm shielded BITS clock cable pair #22 or #24 AWG (0.51 mm² or 0.64 mm²), twisted-pair T1-type...
Page 140: Dlp-G25 Install Lan Wires On The Backplane (Ansi Only)
Output to external device 2 For more detailed information about timing and to set up system timing, see the “NTP-G53 Set Up Note Timing” procedure of the “Turn Up a Network” chapter in the Cisco ONS 15454 DWDM Configuration Guide. Step 2 Return to your originating procedure (NTP).
Page 141: Dlp-G26 Install The Tl1 Craft Interface Wires (Ansi Only)
DLP-G26 Install the TL1 Craft Interface Wires (ANSI Only) Purpose This task installs the TL1 craft interface on the ONS 15454 ANSI shelf using the craft backplane pins. You can also use a LAN cable connected to the TCC2/TCC2P/TCC3 EIA/TIA-232 port to access a TL1 craft interface.
Page 142: Ntp-G11 Install An External Wire-Wrap Panel On The Aep (Ansi Only)
Return to your originating procedure (NTP). NTP-G11 Install an External Wire-Wrap Panel on the AEP (ANSI Only) Purpose This procedure connects an external wire-wrap panel to the ONS 15454 ANSI AEP to provide the physical alarm contacts for the AEP. Tools/Equipment External wire-wrap panel...
Page 143 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G11 Install an External Wire-Wrap Panel on the AEP (ANSI Only) Procedure Step 1 Position the lower cover over the AEP. Make sure that the AEP AMP Champ connectors protrude through the cutouts in the lower cover as shown in the following figure.
Page 144 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G11 Install an External Wire-Wrap Panel on the AEP (ANSI Only) Table 21: Alarm Input Pin Assignments AMP Champ Pin Signal Name AMP Champ Pin Signal Name ALARM_IN_1– ALARM_IN_2– ALARM_IN_3– ALARM_IN_4–...
Page 145 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G11 Install an External Wire-Wrap Panel on the AEP (ANSI Only) Table 22: Alarm Output Pin Assignments AMP Champ Pin Signal Name AMP Champ Pin Signal Name — COM_0 COM_1 —...
Page 146 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G11 Install an External Wire-Wrap Panel on the AEP (ANSI Only) Figure 57: Alarm Input Connector The following figure illustrates the alarm output connectors. Cisco ONS 15454 Hardware Installation Guide...
Page 147: Ntp-G12 Install And Close The Fmec Cover (Etsi Only)
Stop. You have completed this procedure. NTP-G12 Install and Close the FMEC Cover (ETSI Only) Purpose This procedure installs and closes the ONS 15454 ETSI FMEC cover. #2 Phillips Dynamometric screwdriver Tools/Equipment Medium slot-head screwdriver Small slot-head screwdriver...
Page 148: Ntp-G13 Install The Rear Cover (Ansi Only)
NTP-G14 Install DWDM Equipment, on page 123. Stop. You have completed this procedure. NTP-G13 Install the Rear Cover (ANSI Only) Purpose The following procedure explains how to install the rear cover on an ONS 15454 ANSI shelf. Cisco ONS 15454 Hardware Installation Guide...
Page 149 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G13 Install the Rear Cover (ANSI Only) Tools/Equipment #2 Phillips Dynamometric screwdriver Medium slot-head screwdriver Small slot-head screwdriver Prerequisite Procedures NTP-G5 Remove the Backplane Covers (ANSI Only), on page 63 Required/As Needed...
Page 150: Typical Dwdm Rack Layouts
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Typical DWDM Rack Layouts The following figure shows rear cover installation. Figure 61: Installing the Rear Cover Step 6 Continue with the NTP-G14 Install DWDM Equipment, on page 123. Stop. You have completed this procedure.
Page 151 • 2 RU: Y-cable patch panel, 64-channel patch panel, 80-channel patch panel, and mesh patch panel (4 or 8 degree) See the following figure for a typical rack layout. Note Use the rack layout generated by Cisco TransportPlanner to determine your exact shelf layout. Cisco ONS 15454 Hardware Installation Guide...
Page 152 Figure 62: Typical DWDM Equipment Layout in an ONS 15454 ANSI Rack If you are installing a patch-panel or fiber-storage tray below the ONS 15454 shelf, you must install the air ramp between the shelf and patch-panel tray/fiber-management tray, or leave one rack unit (RU) space open.
Page 153: Ntp-G14 Install Dwdm Equipment
TransportPlanner is a DWDM planning tool that is available from your Cisco account representative. Cisco TransportPlanner prepares a shelf plan for each network node and calculates the power and attenuation levels for the DWDM cards installed in the node. For information about Cisco TransportPlanner, refer to the Cisco TransportPlanner DWDM Operations Guide, Release 9.2.
Page 154: Dlp-G28 Install The Fiber Patch-Panel Tray
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G28 Install the Fiber Patch-Panel Tray Tools/Equipment #2 Phillips Dynamometric screwdriver Crimping tool #14 AWG wire and lug Prerequisite None Procedures As needed Required/As Needed Onsite Onsite/Remote Security Level None Procedure Step 1 The DCU chassis requires 1 RU in a standard 19-inch (482.6-mm) or 23-inch (584.2-mm) rack.
Page 155: Dlp-G29 Install The Fiber-Storage Tray
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G29 Install the Fiber-Storage Tray Procedure Step 1 The fiber patch-panel tray requires 1 to 2 RUs of space in a standard 19-inch (482.6-mm) or 23-inch (584.2-mm) rack, depending on whether you are installing a standard or deep patch-panel tray. (The standard tray requires 1 RU, and the deep 32-channel, 40-channel, and mesh patch panel trays each require 2 RUs.) Locate the RMU...
Page 156: Dlp-G371 Install The Ethernet Adapter Panel
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G371 Install the Ethernet Adapter Panel DLP-G371 Install the Ethernet Adapter Panel Purpose This task installs an Ethernet adapter panel (EAP) in an ANSI or ETSI equipment rack. The EAP is used in multishelf node configurations to connect the MS-ISC-100T and the TCC2/TCC2P/TCC3 cards in the subtending nodes.
Page 157: Dlp-G30 Install The Flexlayer Shelf
The Y-cable module tray requires 1 RU in a standard 19-inch (482.6-mm) or 23-inch (584.2-mm) rack. Locate the RMU space specified in your site plan. Use the Cisco TransportPlanner Internal Connections Report to determine how many Y-cable modules you need to install.
Page 158: Dlp-G31 Install The Flexlayer Modules
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G31 Install the FlexLayer Modules DLP-G31 Install the FlexLayer Modules Purpose This task installs the FlexLayer modules in the FlexLayer shelf. You can only install two-channel FlexLayer modules. Tools/Equipment #2 Phillips Dynamometric screwdriver...
Page 159: Dlp-G32 Install The Y-Cable Protection Modules In The Flexlayer Shelf
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G32 Install the Y-Cable Protection Modules in the FlexLayer Shelf Part Number Description 15216-FLB-2-58.9= ITU-100 GHz 2 Ch, FlexMod - 1558.17 and 1558.98 15216-FLB-2-60.6= ITU-100 GHz 2 Ch, FlexMod - 1559.79 and 1560.61 Step 2 Insert the appropriate module into the FlexLayer shelf.
Page 160: Dlp-G377 Install The Y-Cable Protection Modules In The Y-Cable Module Tray
Security Level Procedure Step 1 According to the Cisco TransportPlanner Internal Connections Report, determine which slots you will use to install the Y-cable modules. Step 2 Open the drawer of the tray by pushing inward on the latches located at the left and right front of the tray.
Page 161: Ntp-G15 Install The Common Control Cards
Statement 94 Caution Always use the supplied ESD wristband when working with a powered ONS 15454. For detailed instructions on how to wear the ESD wristband, refer to the...
Page 162: Dlp-G33 Install The Tcc2, Tcc2P, Or Tcc3 Card
Purpose This task installs redundant TCC2/TCC2P/TCC3 cards. The first card you install in the ONS 15454 must be a TCC2/TCC2P/TCC3 card, and it must initialize before you install any cross-connect or traffic cards. Cross-connect cards are only required in hybrid nodes.
Page 163 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G33 Install the TCC2, TCC2P, or TCC3 Card Procedure Step 1 Open the latches/ejectors of the first TCC2/TCC2P/TCC3 card that you will install. Step 2 Use the latches/ejectors to firmly slide the card along the guide rails until the card plugs into the receptacle at the back of the slot (Slot 7 or 11).
Page 164 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf DLP-G33 Install the TCC2, TCC2P, or TCC3 Card • Both green PWR LEDs turn on for 10 seconds. The PWR LEDs then turn red for 2 to 3 minutes before going to steady green. During this time, the ACT/STBY, MJ, and MN LEDs might turn on, followed by the SNYC LED briefly.
Page 165: Dlp-G34 Install The Aic-I Card
TCC2/TCC2P/TCC3 card and install a replacement card. Refer to the release-specific software upgrade document to replace the software. To replace the TCC2/TCC2P/TCC3 card, refer to the Cisco ONS 15454 DWDM Troubleshooting Guide. Step 8 Repeat Steps 1 through 7 for the redundant TCC2/TCC2P/TCC3 card. If both TCC2/TCC2P/TCC3 cards are already installed, proceed to Step 9.
Page 166: Dlp-G309 Install The Ms-Isc-100T Card
Purpose required for a multishelf node configuration. It provides LAN redundancy on the node controller shelf. An alternative to using the MS-ISC-100T card is the Cisco Catalyst 2950, although Cisco recommends using the MS-ISC-100T. For more information on the Catalyst 2950 installation, refer to the Catalyst 2950 product documentation.
Page 167: Multishelf Management
The card can be installed in any slot from Slot 1 to 6 or 12 to 17. Cisco recommends that you install the MS-ISC-100T cards in Slot 6 and Slot Step 3 Verify that the card is inserted correctly and close the latches/ejectors on the card.
Page 168: Ons 15454 Multishelf Node And Subtending Shelves
ONS 15454 Multishelf Node Controller, ONS 15454 M6 and ONS 15454 Subtending Shelves When an ONS 15454 is used as the node controller, a mix of ONS 15454 and ONS 15454 M6 shelves can be subtended through the Cisco Catalyst 3560 switch connected to the node controller or the MS-ISC-100T card connected to the node controller.
Page 169 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G301 Connect the ONS 15454 Multishelf Node and Subtending Shelves to an MS-ISC-100T Card Prerequisite Procedures NTP-G15 Install the Common Control Cards, on page 131 DLP-G371 Install the Ethernet Adapter Panel, on page 126 (Optional) “DLP-G264 Enable Node Security Mode”...
Page 170 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G301 Connect the ONS 15454 Multishelf Node and Subtending Shelves to an MS-ISC-100T Card Figure 65: Connecting the EAP to the Node Controller and Subtending Shelf Step 2 To connect a subtending shelf to the EAP, complete the following (see...
Page 171: Ntp-G304 Configure The Ms-Isc-100T Card For A Ons 15454 Multishelf Node For Non-Default Public And Private Vlan Ids
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G304 Configure the MS-ISC-100T Card for a ONS 15454 Multishelf Node for Non-Default Public and Private VLAN IDs Stop. You have completed this procedure. NTP-G304 Configure the MS-ISC-100T Card for a ONS 15454...
Page 172 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G304 Configure the MS-ISC-100T Card for a ONS 15454 Multishelf Node for Non-Default Public and Private VLAN IDs Step 3 Enter the following commands to configure ports SSC 1 through SSC 7. Replace port with the port number (2 to 8) and repeat for each port.
Page 173: Ntp-G307 Perform The Ons 15454 Shelf Installation Acceptance Test
Onsite Security Level None Procedure Step 1 If you installed an ONS 15454 ETSI shelf, complete the following table by verifying that each applicable procedure was completed. Table 24: ONS 15454 ETSI Shelf Installation Task Summary Description Completed NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves,...
Page 174 Multishelf Node and Subtending Shelves to a Catalyst 2950 or Catalyst 3560, on page 146) Step 2 If you installed an ONS 15454 ANSI shelf, complete the following table by verifying that each applicable procedure was completed. Table 25: ONS 15454 ANSI Shelf Installation Task Summary...
Page 175: Dlp-G35 Inspect The Shelf Installation And Connections
NTP-G295 Connect the ONS 15454 Multishelf Node and Subtending Shelves to a Catalyst 2950 or Catalyst 3560, on page 146 NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby) for a ONS 15454 Multishelf Node, on page 152...
Page 176: Dlp-G36 Measure Voltage
Tools/Equipment • Two Cisco Catalyst 2950 or Cisco Catalyst 3560 switches must be installed in same rack as the node controller shelf; refer to the Cisco Catalyst 2950 or Cisco Catalyst 3560 product documentation for installation instructions. • Cross-over (CAT-5) LAN cables...
Page 177 • Plug the other end into Port 2 of the standby Catalyst 2950 or Catalyst 3560. c) Repeat Steps a and b to connect the additional ONS 15454 subtending shelves in the multishelf configuration using Ports 3 through Port 21 on the Catalyst 2950 or Catalyst 3560 switches.
Page 178 NTP-G296 Upgrade the ONS 15454 Multishelf with MS-ISC Card Configuration Using the Catalyst 3560 Figure 66: Connecting ONS 15454 Multishelf Node and Subtending Shelves to a Catalyst 2950 or Catalyst 3560 NTP-G296 Upgrade the ONS 15454 Multishelf with MS-ISC Card...
Page 179 Step 1 Disconnect the ONS 15454 subtending shelf from the EAPs: a) Remove the cross-over (CAT 5) LAN cable (connecting the ONS 15454 subtending shelf) from the SSC8 port of the right EAP. b) Remove the cross-over (CAT 5) LAN cable (connecting the ONS 15454 subtending shelf) from the SSC8 port of the left EAP.
Page 180 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G297 Upgrade the ONS 15454 Multishelf with Catalyst 2950 Configuration Using the Catalyst 3560 Figure 67: Upgrade the ONS 15454 Multishelf with MS-ISC Card Configuration Using the Catalyst 3560 NTP-G297 Upgrade the ONS 15454 Multishelf with Catalyst 2950...
Page 181 • Plug one connector to Port 1 of the extended Catalyst 3560 (standby). • Plug the other connector to Port 21 of the standby Catalyst 2950. Step 3 Reconnect the ONS 15454 subtending shelf disconnected in Step 1 to the Catalyst 3560 switches: a) Using a cross-over (CAT-5) LAN cable: •...
Page 182: Multishelf Node
VLAN settings of the multishelf node configuration. • The ONS 15454 works with any VLAN ID type. The ONS 15454 M6 works with public VLAN ID of 1 and private VLAN ID of 2.
Page 183 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby) for a ONS 15454 Multishelf Node Step 3 For a 24-port catalyst switch, enter the following commands to configure Ports 2 through 20. Replace port...
Page 184: Ethernet Adapter Panel
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Ethernet Adapter Panel Step 7 Enter the following commands to configure authentication: Example: line con 0 Switch(config)# line vty 0 4 Switch(config)# password yyyyyy Switch(config-line)# login Switch(config-line)# line vty 5 15...
Page 185 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Ethernet Adapter Panel Figure 68: Connecting the EAP to the Node Controller and Subtending Shelf Figure 69: EAP Cable Cisco ONS 15454 Hardware Installation Guide...
Page 186: Filler And Blank Cards
Filler and Blank Cards The filler card (15454- FILLER) is designed to occupy empty multiservice and AIC-I slots in the Cisco ONS 15454 (Slots 1 to 6, 9, and 12 to17). The filler card cannot operate in the cross-connect (XC) slots (Slots 8 and 10) or TCC2/TCC2P/TCC3 slots (Slots 7 and 11).
Page 187: Cable Routing And Management
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Cable Routing and Management Figure 70: Filler Card Faceplate Cable Routing and Management The ONS 15454 cable management facilities include the following: • Fiber patch panels • A cable-routing channel (behind the fold-down door) that runs the width of the shelf...
Page 188: Fiber Management
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Fiber Management Note You can remove the fiber guide, if necessary, to create a larger opening (if you need to route CAT-5 Ethernet cables out the side, for example). To remove the fiber guide, take out the three screws that anchor it to the side of the shelf.
Page 189 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Fiber Management Figure 72: Fiber Capacity The following table provides the maximum capacity of the fiber channel for one side of an ANSI shelf, depending on fiber size and number of Ethernet cables running through that fiber channel.
Page 190: Fiber Management Using The Patch-Panel Trays
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Fiber Management Using the Patch-Panel Trays Determine your fiber size according to the number of cards/ports installed in each side of the shelf. For example, if your port combination requires 36 fibers, 3-mm (0.11-inch) fiber is adequate. If your port combination requires 68 fibers, you must use 2-mm (0.7-inch) or smaller fibers.
Page 191: 40-Channel Patch-Panel Tray
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf 40-Channel Patch-Panel Tray Figure 74: Deep Patch-Panel Tray The following figure shows the label on the patch panel that identifies the wavelength for each port. Figure 75: Patch-Panel Port Wavelength 40-Channel Patch-Panel Tray The 40-channel patch panel tray is 2 RUs deep and comes preinstalled with MPO-LC cables.
Page 192: Mesh Patch-Panel Tray
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Mesh Patch-Panel Tray Figure 76: 40-Channel Patch-Panel Tray, Side View The following figure shows the 40-channel patch-panel ports and corresponding wavelengths. Figure 77: 40-Channel (15454-PP-80) Patch-Panel Port Wavelengths Mesh Patch-Panel Tray There are two mesh patch-panel trays, four-degree (PP-MESH-4) and eight-degree (PP-MESH-8), which are intended for use with mesh nodes.
Page 193: Install Pp-Mesh
Figure 79: Eight-Degree Patch-Panel Tray Install PP-Mesh The PP-Mesh is an ONS 15454 unit that can be installed either above or below the DWDM generating equipment according to the local site practice. The PP-Mesh is a 2 rack unit (RU) high. Each package includes one set of the following brackets: •...
Page 194: Install Pp-Mesh On An Ansi 19" Configuration
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Install PP-Mesh on an ANSI 19" Configuration Figure 80: ANSI and ETSI Brackets Serial Number Specifications ANSI Version- 19” Configuration: Long side mated to unit ANSI Version- 23” Configuration: Short side mated unit...
Page 195 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Install PP-Mesh on an ANSI 19" Configuration Figure 82: Right and Left ANSI 19 Bracket Step 3 Install the right Mesh Panel unit in the ANSI 19" rack. To ensure safe unit mounting, use at least two screws on each side.
Page 196 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Install PP-Mesh on an ANSI 19" Configuration The Vertical Cable Guide can be installed in top position (Figure A), if the fibers are connected from the top, or they can be installed in bottom position (Figure B), if the fibers are connected from the bottom.
Page 197: Install Pp-Mesh On An Ansi 23" Configuration
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Install PP-Mesh on an ANSI 23" Configuration Figure 86: Figure B Serial Number Specifications Rack Vertical Cable Guide Install PP-Mesh on an ANSI 23" Configuration This procedure describes the steps to install the PP-Mesh on an ANSI 23" configuration:...
Page 198 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Install PP-Mesh on an ANSI 23" Configuration Procedure Step 1 Set the mounting brackets to the rack you are using. Step 2 Install the right and left ANSI 23" bracket to the unit using the four washer and the screws provided with the installation kit.
Page 199 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Install PP-Mesh on an ANSI 23" Configuration Figure 89: Mesh Panel Unit, Front View Step 4 Install the right Vertical cable guide (VCG) using the washer and the screw provided with the installation kit.
Page 200 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Install PP-Mesh on an ANSI 23" Configuration Serial Number Specifications Vertical Cable Guide Velcro Tie Wrap Figure 91: Figure B Serial Number Specifications Rack Vertical Cable Guide Cisco ONS 15454 Hardware Installation Guide...
Page 201: Install Pp-Mesh On An Etsi Configuration
Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Install PP-Mesh on an ETSI Configuration Install PP-Mesh on an ETSI Configuration This procedure describes the steps to install the PP-Mesh on an ETSI configuration: Procedure Step 1 Set the mounting brackets to the rack you are using.
Page 202 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Install PP-Mesh on an ETSI Configuration Figure 94: Mesh Panel Unit in ETSI Rack, Front View Step 4 Install the right Vertical cable guide (VCG) using the washer and the screw provided with the installation kit.
Page 203: Fiber Management Using The Y-Cable Module Tray
Fiber Management Using the Fiber-Storage Tray Cisco recommends installing at least one fiber-storage tray in multinode racks to facilitate fiber-optic cable management for DWDM applications. This tray is usually used to store slack cable from cables installed between cards within a single node.
Page 204 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Fiber Management Using the Fiber-Storage Tray Figure 97: Optical Fiber With Exposed Ferrule Figure 98: Optical Fiber Without Exposed Ferrule The following table provides the fiber capacity for each tray. Table 28: Fiber-Storage Tray Capacity...
Page 205: Fiber Management Using The Optional Ansi Tie-Down Bar
The following figure shows the tie-down bar, the ONS 15454 ANSI, and the rack. Figure 100: Tie-Down Bar on the Cisco ONS 15454 ANSI Shelf...
Page 206 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf Fiber Management Using the Optional ANSI Tie-Down Bar Cisco ONS 15454 Hardware Installation Guide...
Page 207: Installing The Ons 15454 M2 Shelf
The ONS 15454 M2 shelf is mounted on a 19-inch (482.6-mm) or 23-inch (584.2-mm) equipment rack. Make sure that the correct type of 19-inch ANSI rack is used for mounting the ONS 15454 M2 shelf as shown in Figure 1: 19-inch ANSI Rack Post Recommended for Cisco ONS 15454 M6 and M2 Shelves, on page If the shelf is mounted in the front position, then it projects 1.7 inches (43.18 mm) from the front of the rack.
Page 208: Mounting Brackets
Caution When mounting the ONS 15454 M2 shelf in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M2 shipping kit, or remove the coating from the threads to ensure electrical continuity.
Page 209: Mounting A Single Node
The ONS 15454 M2 shelves can be mounted above each other without any space between the shelves. This method of mounting does not restrict the air flow because the air vents are on either sides of the ONS 15454 M2 shelves.
Page 210: Mounting A Single Node
The ONS 15454 M2 shelves can be mounted above each other without any space between the shelves. This method of mounting does not restrict the air flow because the air vents are on either sides of the ONS 15454 M2 shelves.
Page 211: Desktop Mounting The Ons 15454 M2 Shelf
The ONS 15454 M2 shelf can be mounted on the desktop for easy access. Air Deflector An air deflector is a sheet-metal part that is mounted on the ONS 15454 M2 shelf to orient the air flow in a specific direction.
Page 212: Air Plenum Rack And Cabinet Compatibility
Installing the ONS 15454 M2 Shelf Air Plenum Rack and Cabinet Compatibility Figure 104: Dimension of Cisco ONS 15454 M2 chassis relative to the air plenum Figure 105: Dimension on Cisco ONS 15454 M2 relative to the air plenum Air Plenum Rack and Cabinet Compatibility The table shows the compatibility of air plenum with the ANSI and ETSI racks and cabinets.
Page 213: Ntp-G343 Install The Air Plenum In Ons 15454 M2 Shelf
Installing the ONS 15454 M2 Shelf NTP-G343 Install the Air Plenum in ONS 15454 M2 Shelf 1 A minimum opening of 20.600 inches is required to install the vertical air plenum behind the front rails. Note The ANSI 19-inch two post rack that is compatible with air plenum installation is available from Telect, with part number 12545-301.
Page 214 For nominal voltage of -60 VDC, the input voltage range is from -40 to -72 VDC. Note Use only the fastening hardware provided with the ONS 15454 M2 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.
Page 215: Dlp-G763 Install Air Plenum For Ons 15454 M2 Shelf In Ansi 19-Inch Configuration
DLP-G763 Install Air Plenum for ONS 15454 M2 Shelf in ANSI 19-inch Configuration DLP-G763 Install Air Plenum for ONS 15454 M2 Shelf in ANSI 19-inch Configuration Purpose This task installs the air plenum for the ONS 15454 M2 shelf in ANSI 19-inch cabinet or rack configuration. • #2 Phillips Dynamometric screwdriver Tools/Equipment •...
Page 216 Step 5 Install the 19-inch standard brackets on both sides of the chassis in the front position. See DLP-G582 Mounting the 19-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration, on page 197. Step 6 Install the ONS 15454 M2 empty chassis below the horizontal plenum.
Page 217: Dlp-G764 Install Air Plenum In Ons 15454 M2 Shelf For Ansi 23-Inch Configuration
Return to your originating procedure (NTP). DLP-G764 Install Air Plenum in ONS 15454 M2 Shelf for ANSI 23-inch Configuration Purpose This task installs the air plenum for the ONS 15454 M2 shelf in the ANSI 23-inch cabinet or rack configuration. Tools/Equipment •...
Page 218 Installing the ONS 15454 M2 Shelf DLP-G764 Install Air Plenum in ONS 15454 M2 Shelf for ANSI 23-inch Configuration Procedure Step 1 Install the ANSI 23-inch adapter plates on the horizontal air plenum. Step 2 Align the screws to fix the adapter plates to the shelf. Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).
Page 219 Installing the ONS 15454 M2 Shelf DLP-G764 Install Air Plenum in ONS 15454 M2 Shelf for ANSI 23-inch Configuration Figure 112: Installing the horizontal air plenum in the ANSI 23-inch configuration Step 5 Install the vertical air plenum to the left of the horizontal air plenum: a) Insert the vertical air plenum in the free space between the horizontal air plenum and cabinet.
Page 220 Install ANSI 19-inch standard brackets on both sides of the chassis in front position. See DLP-G582 Mounting the 19-inch Brackets on the ONS 15454 M2 Shelf for ANSI Rack Configuration, on page 197 Step 8 Install the ONS 15454 M2 empty chassis below the horizontal plenum.
Page 221: Dlp-G765 Install Air Plenum For Ons 15454 M2 Shelf In Etsi Configuration
DLP-G765 Install Air Plenum for ONS 15454 M2 Shelf in ETSI Configuration DLP-G765 Install Air Plenum for ONS 15454 M2 Shelf in ETSI Configuration Purpose This task installs the air plenum for the ONS 15454 M2 shelf in the ETSI configuration. Tools/Equipment • #2 Phillips Dynamometric screwdriver •...
Page 222 Installing the ONS 15454 M2 Shelf DLP-G765 Install Air Plenum for ONS 15454 M2 Shelf in ETSI Configuration Figure 116: Installing the adapter plates on the horizontal air plenum Step 3 Place the horizontal plenum above the chassis slot in the ETSI cabinet.
Page 223 Step 7 Install the ANSI 19-inch mounting brackets on both sides of the chassis in front position. See DLP-G588 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration, on page 208. Step 8 Install the ONS 15454 M2 empty chassis below the horizontal plenum.
Page 224 Installing the ONS 15454 M2 Shelf NTP-G266 Install the ONS 15454 M2 Shelf Figure 120: Installing the ONS 15454 M2 chassis below the horizontal air plenum Step 9 Return to your originating procedure (NTP). NTP-G266 Install the ONS 15454 M2 Shelf This procedure installs the shelf.
Page 225 (25.4 mm) Statement 1076 Note Make sure that the correct type of 19-inch ANSI rack is used for mounting the ONS 15454 M2 shelf as shown Figure 1: 19-inch ANSI Rack Post Recommended for Cisco ONS 15454 M6 and M2 Shelves, on page...
Page 226 NTP-G266 Install the ONS 15454 M2 Shelf Note During installation, do not use the door to handle the chassis. Note Remove the door from the ONS 15454 M2 shelf and reinstall it after installation of all the other modules is complete. Procedure Step 1 Complete the necessary task as applicable: •...
Page 227: Configuration
Caution When mounting the ONS 15454 M2 in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M2 ship kit, or remove the coating from the threads to ensure electrical continuity.
Page 228: Configuration
Caution When mounting the ONS 15454 M2 in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M2 ship kit, or remove the coating from the threads to ensure electrical continuity.
Page 229: Shelf For Ansi Rack Configuration
Installing the ONS 15454 M2 Shelf DLP-G584 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ANSI Rack Configuration Note The mounting brackets can be installed in the front or the middle position of the chassis.
Page 230 Installing the ONS 15454 M2 Shelf DLP-G584 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ANSI Rack Configuration Prerequisite Procedures NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves, on page...
Page 231 Installing the ONS 15454 M2 Shelf DLP-G584 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ANSI Rack Configuration Step 13 Place the 23-inch mounting bracket flush in the front position (see Diagram 1 of...
Page 232: Dlp-G585 Mounting The Brackets On The Ons 1545 M2 Shelf For Etsi Rack Configuration
Caution When mounting the ONS 15454 M2 in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M2 ship kit, or remove the coating from the threads to ensure electrical continuity.
Page 233 Installing the ONS 15454 M2 Shelf DLP-G586 Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M2 Shelf for ETSI Rack Configuration Figure 125: Mounting the Brackets on the ONS 15454 M2 Shelf for ETSI Rack Configuration Step 5 Return to your originating procedure (NTP).
Page 234 Air Deflectors (Front-to-Front) on the ONS 15454 M2 Shelf for ETSI Rack Configuration, on page 205. If the 100G-LC-C, 10x10G-LC, or CFP-LC cards are to be installed in the ONS 15454 M2 shelf, Note do not mount the left front deflector (exhaust air deflector). Use the standard brackets directly to mount the ONS 15454 M2 shelf.
Page 235: Dlp-G587 Mounting The Bracket With Air Deflectors (Front-To-Back) On The Ons 15454 M2
Installing the ONS 15454 M2 Shelf DLP-G587 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration Figure 126: Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M2 Shelf for ETSI Rack Configuration Step 16 Return to your originating procedure (NTP).
Page 236 Installing the ONS 15454 M2 Shelf DLP-G587 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration Procedure Step 1 Place the right front air deflector flush against the right side of the chassis as shown in Diagram 1 of...
Page 237 DLP-G587 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration Figure 127: Mounting the Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration Figure 128: Mounting the Brackets with Air Deflectors (Front-to-Back) on the ONS 15454 M2 Shelf for ETSI Rack Configuration Step 16 Return to your originating procedure (NTP).
Page 238: Dlp-G588 Mounting The Bracket With Air Deflectors (Front-To-Top) On The Ons 15454 M2 Shelf For Etsi Rack Configuration
Installing the ONS 15454 M2 Shelf DLP-G588 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration DLP-G588 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration...
Page 239: Dlp-G589 Mount The Ons 15454 M2 Shelf On A Rack (One Person)
Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration, on page 209. Figure 129: Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M2 Shelf for ETSI Rack Configuration Step 15 Return to your originating procedure (NTP).
Page 240 Note The ONS 15454 M2 requires a minimum of 3.5 inches (88.9 mm) of vertical rack space. To ensure that the mounting is secure, use two to three M6 mounting screws on each side of the shelf. A shelf should be mounted at the bottom of the rack if it is the only unit in the rack.
Page 241: Dlp-G590 Mount The Ons 15454 M2 Shelf On The Wall
Lift the shelf to the desired position in the rack. Note To ensure proper cooling of the ONS 15454 M2 shelf, make sure that the space in front of the air flow vents are free of cables, fibers, and mechanical fixtures for fiber and cable management.
Page 242 M2 shelf assembly on the wall. The type of screws used to mount the brackets on the wall depends on the wall-type and are not provided by Cisco. The screws used must be able to sustain an overall weight of at least 20 kg (44 lb).
Page 243 Step 5 Align the fire protective drip tray screw holes against the wall mounting bracket screw holes (see diagram 1 Figure 130: Mounting an ONS 15454 M2 in a Rack, on page 211). The fire protective drip tray is present in the wall mount accessory kit provided by Cisco.
Page 244: Dlp-G591 Mount The Ons 15454 M2 Shelf On The Desktop
DLP-G591 Mount the ONS 15454 M2 Shelf on the Desktop This task explains mount the shelf on the desktop. Purpose Tools/Equipment None Prerequisite Procedures NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves, on page As needed Required/As Needed Onsite/Remote Onsite...
Page 245: Front Door
Place the ONS 15454 M2 shelf upside down on a smooth, flat surface. Note To ensure proper cooling of the ONS 15454 M2 shelf, make sure that the space in front of the air flow vents are free of cables, fibers, and mechanical fixtures for fiber and cable management.
Page 246: Ntp-G269 Install The Standard Door Of The Ons 15454 M2 Shelf
Figure 134: ONS 15454 M2 Front-Door Erasable Label The laser warning label is placed on top of the chassis. The following figure shows the label placed on the ONS 15454 M2 surface, inside the shelf close to the door hinges, below Slot 1.
Page 247 Installing the ONS 15454 M2 Shelf NTP-G269 Install the Standard Door of the ONS 15454 M2 Shelf Figure 136: Installing the Standard Door Step 2 Align the standard door hinges with the chassis hinges. Step 3 Release the hinge pins.
Page 248: Ntp-G270 Open And Remove The Standard Door Of The Ons 15454 M2 Shelf
Installing the ONS 15454 M2 Shelf NTP-G270 Open and Remove the Standard Door of the ONS 15454 M2 Shelf Step 5 Tighten the door screws to a torque value of 6.5 in-lb (0.75 N-m) to close the standard door as shown in the following figure.
Page 249: Dlp-G594 Open The Standard Door Of The Ons 15454 M2 Shelf
Caution The ONS 15454 M2 shelf has an ESD plug input and is shipped with an ESD wrist strap. The ESD plug input is located on the outside of the shelf on the right side. It is labeled “ESD” on the top and bottom. Always wear an ESD wrist strap and connect the strap to the ESD plug when working on the ONS 15454 M2.
Page 250: Dlp-G595 Remove The Standard Door Of The Ons 15454 M2 Shelf
#2 Phillips Dynamometric screwdriver Prerequisite Procedures • DLP-G594 Open the Standard Door of the ONS 15454 M2 Shelf, on page 219. • Connect the chassis to the office ground. For detailed instructions on how to ground the chassis, refer to the...
Page 251 Installing the ONS 15454 M2 Shelf DLP-G595 Remove the Standard Door of the ONS 15454 M2 Shelf Figure 141: Removing the Standard Door Step 3 Pull the hinge pins holding the door to the chassis, in the opposite direction. Step 4 Remove the door from its hinges as shown in the following figure.
Page 252: Ntp-G343 Install The Deep-Front Panel Of The Ons 15454 M2 Shelf
Caution The deep-front panel does not have a hinge and cannot be rotated like a standard door. Rotating the deep front panel can damage the deep-front panel, shelf hinges, other devices and cables placed below the ONS 15454 M2 shelf.
Page 253 Installing the ONS 15454 M2 Shelf NTP-G343 Install the Deep-Front Panel of the ONS 15454 M2 Shelf Figure 143: Inserting the Lug to the Shelf Step 2 Loosen the deep-front panel screws and slide them outwards using the plastic tabs (see the following figure).
Page 254 Installing the ONS 15454 M2 Shelf NTP-G343 Install the Deep-Front Panel of the ONS 15454 M2 Shelf Figure 145: Moving Deep-Front Panel and Shelf in line Step 4 Align the deep-front panel with the shelf by performing these sub-steps at the same time:...
Page 255 Installing the ONS 15454 M2 Shelf NTP-G343 Install the Deep-Front Panel of the ONS 15454 M2 Shelf Figure 147: Engaging the Deep-Front Panel and Shelf Step 5 Slide the deep-front panel screws inwards using the plastic tabs to engage the retention features and the pins with the shelf notches and hinges (see the following figure).
Page 256: Ntp-G331 Remove The Deep-Front Panel Of The Ons 15454 M2 Shelf
Caution The deep-front panel does not have a hinge and cannot be rotated like a standard door. Rotating the deep front panel can damage the deep-front panel, shelf hinges, other devices and cables placed below the ONS 15454 M2 shelf.
Page 257 Installing the ONS 15454 M2 Shelf NTP-G331 Remove the Deep-Front Panel of the ONS 15454 M2 Shelf Procedure Step 1 Remove the end of the ground strap cable that is connected to the exterior of the deep-front panel (see the following figure).
Page 258: Power Modules
Remove the lug and tighten the nut on the shelf to a torque value of 11.5 in-lb (1.3 N-m). Stop. You have completed this procedure. Power Modules The ONS 15454 M2 system contains the following pluggable power modules: • AC power module • DC power module...
Page 259: Ac Power Module
TNCS-2O, or TSCE) in all the three states (OFF/red/green). The AC power module supports the lamp test procedure and the LED changes its color or state. The fans in the ONS 15454 M2 shelf cool the AC module and guarantee proper operation across the complete operating temperature or output power range.
Page 260: Dc Power Module
DC Power Module The ONS 15454 M2 system can be powered by redundant DC power lines, however a single power line can power the entire ONS 15454 M2 system. The DC power module draws the power from the batteries to turn on the ONS 15454 M2.
Page 261: Dlp-G592 Install The Ac Power Module In The Ons 15454 M2 Shelf
Step 1 Complete the necessary task as applicable: • DLP-G592 Install the AC Power Module in the ONS 15454 M2 Shelf, on page 231 • DLP-G593 Install the DC Power Module in the ONS 15454 M2 Shelf, on page 233...
Page 262 Installing the ONS 15454 M2 Shelf DLP-G592 Install the AC Power Module in the ONS 15454 M2 Shelf Figure 154: Installing the AC Power Module Step 2 Plug the AC power module completely into the chassis. Step 3 Tighten the screw to a torque value of 4 in-lb (0.45 N-m) to lock the power module in the chassis (see the following figure).
Page 263: Dlp-G593 Install The Dc Power Module In The Ons 15454 M2 Shelf
DLP-G593 Install the DC Power Module in the ONS 15454 M2 Shelf DLP-G593 Install the DC Power Module in the ONS 15454 M2 Shelf Purpose This task installs the DC power module in the ONS 15454 M2 system. Tools/Equipment #2 Phillips Dynamometric screwdriver Prerequisite Procedures •...
Page 264: Fan-Tray Assembly
15454-M2-FTA2 is compatible with R9.2.0 and later releases. The fan-tray assembly is installed on the left side of the ONS 15454 M2 shelf. The fan-tray assembly is removable and holds the fan-control circuitry and the fans for the ONS 15454 M2 shelf.
Page 265: Fan Speed
Inventory tab of CTC after a delay of approximately 6 minutes. After you install the fan-tray, you should only access it if a fan failure occurs. To clean and replace the fan-tray assembly, see the “Maintain the Node” chapter in the Cisco ONS 15454 DWDM Configuration Guide. Note If the fan-tray assembly is removed from the shelf, wait for at least 5 seconds before plugging it back into the shelf.
Page 266 Note The 15454-M2-FTA2 is compatible with R9.2.0 and later releases. Caution Do not operate an ONS 15454 M2 shelf without an air filter. For information on the air filter, see NTP-G114 Inspect and Replace the Air Filter, on page 435.
Page 267: Power And Ground Description
The grounding configuration is mandatory for ANSI and ETSI chassis for both AC and DC configurations. The following sections describe power and ground for the ONS 15454 M2 shelves. For detailed instructions on grounding the ONS 15454 M2 chassis, see the...
Page 268: Ansi Power And Ground
ANSI Power and Ground For AC power feed, use the power cable shipped with the ONS 15454 M2 and one ground cable. For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For low input voltage ranges, 100V to 127Vac, the branch circuit protection must not be rated more than 20A.
Page 269: Ntp-G271 Install The Power And Ground To The Ons 15454 M2 Shelf
• Two-hole grounding lug, shipped with the ONS 15454 M2 Prerequisite Procedures • NTP-G267 Install the Power Module in the ONS 15454 M2 Shelf, on page 230. • Connect the chassis to the office ground. For detailed instructions on how...
Page 270 Installing the ONS 15454 M2 Shelf NTP-G271 Install the Power and Ground to the ONS 15454 M2 Shelf Warning Blank faceplates (filler panels) serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment;...
Page 271: Dlp-G596 Connect Office Power (Ac) To The Ons 15454 M2 Shelf
DLP-G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only), on page 249 Step 3 Connect the office ground to the ONS 15454 M2 shelf. For detailed instructions on grounding, refer to the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms...
Page 272 NFPA 70, the National Electrical Code (NEC). Statement 7012 Caution The ONS 15454 M2 relies on the protective devices in the building installation to protect against short circuit, overcurrent and ground faults. Ensure that the protective devices are properly rated and comply with national and local codes.
Page 273 If the system loses power or if both TNC, TNCE, TSC, TNCS-2, TNCS-2O, or TSCE cards are reset, you must reset the ONS 15454 M2 clock. After powering down, the date defaults to January 1, 1970, 00:04:15. To reset the clock, see the NTP-G24 Setting Up Node Identification Information.
Page 274: Dlp-G597 Connect Office Power (Dc) To The Ons 15454 M2 Shelf (Ansi Only)
Installing the ONS 15454 M2 Shelf DLP-G597 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ANSI Only) Figure 162: Cable Clip to Secure the Power Cable Step 4 Connect the power cable to the fuse panel or power source.
Page 275 Statement 1075 Caution The ONS 15454 M2 relies on the protective devices in the building installation to protect against short circuit, overcurrent, and ground faults. Ensure that the protective devices are properly rated and comply with national and local codes.
Page 276 Network Time Protocol/Simple Network Time Protocol (NTP/SNTP) server, you must reset the ONS 15454 clock. After powering down, the date defaults to January 1, 1970, 00:04:15. To reset the clock, see the NTP-G24 Setting Up Node Identification Information.
Page 277 Installing the ONS 15454 M2 Shelf DLP-G597 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ANSI Only) Figure 163: Connecting Office Power—DC Power Module (ANSI Only) Step 9 Insert the lugs as shown in the following figure. Cisco ONS 15454 Hardware Installation Guide...
Page 278 Installing the ONS 15454 M2 Shelf DLP-G597 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ANSI Only) Figure 164: Connecting Office Power—DC Power Module (ANSI Only) Note There are two DC power terminals—A and B. Each power terminal is connected with two cables—one for RET and the other for -48V.
Page 279: Dlp-G598 Connect Office Power (Dc) To The Ons 15454 M2 Shelf (Etsi Only)
Installing the ONS 15454 M2 Shelf DLP-G598 Connect Office Power (DC) to the ONS 15454 M2 Shelf (ETSI Only) Before you make any crimp connections, coat all bare conductors (battery, battery return, and frame Caution ground) with an appropriate antioxidant compound. Bring all unplated connectors, braided strap, and bus bars to a bright finish, then coat with an antioxidant before you connect them.
Page 280 The battery return connection is treated as DC-I, as defined in Telcordia GR-1089-CORE Issue 5. Caution The ONS 15454 M2 relies on the protective devices in the building installation to protect against short circuit, overcurrent, and ground faults. Ensure that the protective devices are properly rated and comply with national and local codes.
Page 281: Dlp-G599 Turn On And Verify Ac Office Power On The Ons 15454 M2 Shelf
Installing the ONS 15454 M2 Shelf DLP-G599 Turn On and Verify AC Office Power on the ONS 15454 M2 Shelf Step 3 Attach the DC ETSI power cables to the DSUB power connectors of the DC power module (see the following figure).
Page 282: Dlp-G600 Turn On And Verify Dc Office Power On The Ons 15454 M2 Shelf
15A in case of AC power. Step 2 If the ONS 15454 M2 does not power up, check the voltage at the power source using a voltmeter. The voltage should be 100 to 240 VAC +/-10 percent. Step 3 Return to your originating procedure (NTP).
Page 283 To power up the node, insert the fuse into the fuse position according to site practice. The fuse rating must not exceed 15A. Step 3 Using a voltmeter, verify the ONS 15454 M2 shelf for –48 VDC battery and ground: Cisco ONS 15454 Hardware Installation Guide...
Page 284: Ntp-G291 Attach Wires To Timing, Lan, And Craft Pin Connections In Ons 15454 M2
Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms Note To route the copper cables from the SFPs or RJ-45 ports in a ONS 15454 M2 shelf, removal of the shelf door is mandatory. Note The minimum distance between the fiber LC connector and the bulk attenuator must be at least 50 cm. This is the minimum distance required to place the bulk attenuator outside the shelf from any port of a card.
Page 285: Dlp-G292 Install Timing Wires In Ons 15454 M2 - Ansi
DLP-G292 Install Timing Wires in ONS 15454 M2 - ANSI Procedure Step 1 Complete either DLP-G292 Install Timing Wires in ONS 15454 M2 - ANSI, on page 255 DLP-G293 Install Timing Wires in ONS 15454 M2 - ETSI, on page 257 if you are provisioning external timing.
Page 286 Installing the ONS 15454 M2 Shelf DLP-G292 Install Timing Wires in ONS 15454 M2 - ANSI Figure 168: DC-2 Power Module ANSI BITS connectors Cisco ONS 15454 Hardware Installation Guide...
Page 287: Dlp-G293 Install Timing Wires In Ons 15454 M2 - Etsi
Installing the ONS 15454 M2 Shelf DLP-G293 Install Timing Wires in ONS 15454 M2 - ETSI Figure 169: AC-2 Power Module ANSI BITS Connectors Step 2 Connect the wire wrap cable to the appropriate timing connector in the Power Module.
Page 288 Installing the ONS 15454 M2 Shelf DLP-G293 Install Timing Wires in ONS 15454 M2 - ETSI Tools/Equipment 75-ohm coaxial cable with a DIN 1.0/2.3 miniature coax connector. The PID for the BITS IN/OUT cable is 15454-M-TMGCBL=. Prerequisite Procedures None Required/As Needed...
Page 289 Installing the ONS 15454 M2 Shelf DLP-G293 Install Timing Wires in ONS 15454 M2 - ETSI Figure 170: DC-2E Power Module ETSI BITS Connectors Cisco ONS 15454 Hardware Installation Guide...
Page 290 Installing the ONS 15454 M2 Shelf DLP-G293 Install Timing Wires in ONS 15454 M2 - ETSI Figure 171: AC-2 Power Module ETSI BITS Connectors Step 2 Using a coaxial cable with DIN 1.0/2.3 miniature coax connectors, connect the clock cable to the appropriate connector in the Power Module.
Page 291: Dlp-G294 Install Lan Wires In Ons 15454 M2
Crimping tool for RJ-45 connector 0.51 mm² or 0.64 mm² (#22 or #24 AWG) wire, preferably standard CAT-5 Prerequisite Procedures NTP-G267 Install the Power Module in the ONS 15454 M2 Shelf, on page 230 Required/As Needed As needed Onsite/Remote...
Page 292: Dlp-G604 Install The Tnc, Tnce, Tsc, Or Tsce Card
Statement 94 Caution Always use the supplied ESD wristband when working with a powered ONS 15454 M2 and ONS 15454 M6 shelf assemblies. For detailed instructions on how to wear the ESD wristband, refer to the...
Page 293 Use the latches/ejectors to firmly slide the card horizontally along the guide rails until the card plugs into the receptacle at the back of the slot (slot 1 or 8 in the ONS 15454 M6 shelf and slot 1 in the ONS 15454 M2 shelf).
Page 294 If the FAIL LED is on continuously, see the tip in step 8 about the TNC/TNCE/TSC/TSCE/TNCS-2/TNCS-2O card automatic upload. The following figure illustrates the installation of TNC and TNCE cards on ONS 15454 M6 shelf. Figure 172: Installing TNC and TNCE cards on ONS 15454 M6 Shelf...
Page 295: Dlp-G605 Provision Ppm And Port For The Tnc And Tnce Cards
DLP-G605 Provision PPM and Port for the TNC and TNCE Cards Purpose (ONS 15454 M2 and ONS 15454 M6 only) This task provisions a PPM and port on a TNC and TNCE cards. PPMs are created to support the OSC function.
Page 296: Dlp-G606 Configure Udc And Voip For The Tnc And Tnce Cards
Return to your originating procedure (NTP). DLP-G606 Configure UDC and VoIP for the TNC and TNCE Cards Purpose (ONS 15454 M2 and ONS 15454 M6 only) This task configures UDC and VoIP traffic for the TNC and TNCE cards. Tools/Equipment...
Page 297: Ntp-G275 Perform The Ons 15454 M2 Shelf Installation Acceptance Test
Onsite Security Level None Procedure Step 1 If you installed an ONS 15454 M2 shelf, complete the following table by verifying that each applicable procedure was completed. Table 31: ONS 15454 M2 ETSI Shelf Installation Task Summary Description Completed NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves,...
Page 298: Dlp-G601 Inspect The Ons 15454 M2 Shelf Installation And Connections
Description Completed DLP-G604 Install the TNC, TNCE, TSC, or TSCE Card, on page 262 NTP-G269 Install the Standard Door of the ONS 15454 M2 Shelf, on page 216 Step 2 Complete the DLP-G601 Inspect the ONS 15454 M2 Shelf Installation and Connections , on page 268.
Page 299: Filler And Blank Cards
Filler and Blank Cards Filler cards must be installed in unused and empty slots to ensure proper air flow and electromagnetic interference (EMI) requirements during the ONS 15454 M2 operation. There are two types of card fillers: • Line card fillers (15454-M-FILLER) that operate in slots 2 and 3.
Page 300: Air Filter
Air Filter The ONS 15454 M2 contains a preinstalled reusable air filter (15454 M2-FTF) on the right side of the shelf. The reusable filter is made up of a gray, open-cell, polyurethane foam that is specially coated to provide fire and fungi resistance.
Page 301: Installing The Ons 15454 M6 Shelf
NTP-G258 Install the Standard Door of the ONS 15454 M6 Shelf , on page 323 • NTP-G259 Open and Remove the Standard Door of the ONS 15454 M6 Shelf , on page 327 • NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf, on page 332 •...
Page 302: Ansi Rack Installation
The ONS 15454 M6 shelf is mounted on a 19-inch (482.6-mm) or 23-inch (584.2-mm) equipment rack. Make sure that the correct type of 19-inch ANSI rack is used for mounting the ONS 15454 M6 shelf as shown in Figure 1: 19-inch ANSI Rack Post Recommended for Cisco ONS 15454 M6 and M2 Shelves, on page If the shelf is mounted in the front position, then it projects 1.7 inches (43.18 mm) from the front of the rack.
Page 303: Reversible Mounting Bracket
Mounting a Single Shelf Mounting the ONS 15454 M6 shelf on a rack requires a minimum of 10.4-inches (265 mm) of vertical rack space. To ensure that the mounting is secure, use two to three #12-24 mounting screws for each side of the shelf.
Page 304: Mounting Multiple Nodes
ONS 15454 M6 shelves and a fuse and alarm panel. However, unequal flange racks are limited to six ONS 15454 M6 shelves and a fuse and alarm panel, or seven ONS 15454 M6 shelves using a fuse and alarm panel from an adjacent rack.
Page 305: Mounting A Single Node
In an ETSI rack, the brackets are mounted only in the front position. If the ONS 15454 M6 shelf is fully loaded, then two people should install it. However, it is possible for one person to install an empty shelf. The shelf should be empty for easier lifting. For information on the ONS...
Page 306: Mounting Multiple Nodes
M6 shelves. Air Deflector An air deflector is a sheet-metal part that is mounted on the ONS 15454 M6 shelf to orient the air flow in a specific direction. The air deflectors can be mounted in different positions to control the air flow: •...
Page 307 Figure 175: Air flow within the air plenum in the cabinet The following two figures shows the dimensions of the air plenum relative to the cabinet or rack. Figure 176: Dimension of Cisco ONS 15454 M6 chassis relative to the air plenum Cisco ONS 15454 Hardware Installation Guide...
Page 308: Air Plenum Rack And Cabinet Compatibility
Installing the ONS 15454 M6 Shelf Air Plenum Rack and Cabinet Compatibility Figure 177: Dimension on Cisco ONS 15454 M6 relative to the air plenum Air Plenum Rack and Cabinet Compatibility The table shows the compatibility of air plenum with the ANSI and ETSI racks and cabinets. The chassis can be installed with brackets in front position only.
Page 309 Installing the ONS 15454 M6 Shelf NTP-G344 Install the Air Plenum in ONS 15454 M6 Shelf Figure 178: Minimum rear opening for ANSI 19-inch and ETSI configuration NTP-G344 Install the Air Plenum in ONS 15454 M6 Shelf Purpose This procedure installs the air plenum to orient the air flow from front-to- back direction in the ONS 15454 M6 shelf.
Page 310 For nominal voltage of -60 VDC, the input voltage range is from -40 to -72 VDC. Note Use only the fastening hardware provided with the ONS 15454 M6 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.
Page 311 Installing the ONS 15454 M6 Shelf DLP-G766 Install Air Plenum for ONS 15454 M6 Shelf in ANSI 19-inch Cabinet Tools/Equipment • #2 Phillips Dynamometric screwdriver • Medium slot-head screwdriver • Small slot-head screwdriver • Screws: #12-24 x 0.50 pan-head Phillips screws (8) •...
Page 312 Installing the ONS 15454 M6 Shelf DLP-G766 Install Air Plenum for ONS 15454 M6 Shelf in ANSI 19-inch Cabinet Figure 180: Installing the left vertical air plenum Step 4 Install the vertical air plenum to the right of the horizontal air plenum. Follow step 3a to step 3c.
Page 313 Step 6 Install the 19-inch standard brackets on both sides of the chassis in the front position. See DLP-G560 Mounting the Reversible Brackets on the ONS 15454 M6 Shelf for ANSI Rack Configuration, on page 299. Step 7 Check the length between the top and bottom horizontal air plenums where the chassis will be installed. The length must be not less than 10.5 inches (267 mm).
Page 314 DLP-G767 Install Air Plenum in ONS 15454 M6 Shelf for ANSI 23-inch Configuration Purpose This task installs the air plenum for the ONS 15454 M6 shelf in the ANSI 23-inch cabinet or rack configuration. Tools/Equipment • #2 Phillips Dynamometric screwdriver •...
Page 315 Installing the ONS 15454 M6 Shelf DLP-G767 Install Air Plenum in ONS 15454 M6 Shelf for ANSI 23-inch Configuration Figure 185: Installing the bottom horizontal air plenum in the ANSI 23-inch configuration Step 5 Install the vertical air plenum to the left of the horizontal air plenum: a) Insert the vertical air plenum in the free space between the horizontal air plenum and cabinet.
Page 316 Step 9 Install ANSI 23-inch standard brackets on both sides of the chassis in front position. See DLP-G562 Mounting the Brackets on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on page 304. Step 10 Check the length between the top and bottom horizontal air plenums where the chassis will be installed. The length must be not less than 10.5 inches (267 mm).
Page 317 Step 12 Return to your originating procedure (NTP). DLP-G768 Install Pre-assembled Air Plenums in ANSI 23-inch Configuration This task installs pre-assembled air plenums for the ONS 15454 M6 shelf in the ANSI Purpose 23-inch configuration. • #2 Phillips Dynamometric screwdriver Tools/Equipment •...
Page 318 Installing the ONS 15454 M6 Shelf DLP-G768 Install Pre-assembled Air Plenums in ANSI 23-inch Configuration Step 6 Install the vertical air plenum to the right of the horizontal air plenum. Follow step 4. Step 7 Install the horizontal air plenum above the vertical air plenums. Follow step 4.
Page 319 Return to your originating procedure (NTP). DLP-G769 Install Air Plenum for ONS 15454 M6 Shelf in ETSI Configuration This task installs the air plenum for the ONS 15454 M6 shelf in the ETSI configuration. Purpose Cisco ONS 15454 Hardware Installation Guide...
Page 320 Installing the ONS 15454 M6 Shelf DLP-G769 Install Air Plenum for ONS 15454 M6 Shelf in ETSI Configuration Tools/Equipment • #2 Phillips Dynamometric screwdriver • Medium slot-head screwdriver • Small slot-head screwdriver • Screws: M6.0 x 20 pan-head Phillips screws (8) •...
Page 321 Installing the ONS 15454 M6 Shelf DLP-G769 Install Air Plenum for ONS 15454 M6 Shelf in ETSI Configuration Figure 193: Installing the horizontal air plenum in the ETSI configuration Step 5 Install the vertical air plenum to the left of the horizontal air plenum: a) Insert the vertical plenum in the free space between the horizontal plenum and cabinet.
Page 322 Step 9 Install the standard brackets on both sides of the chassis in front position. See DLP-G562 Mounting the Brackets on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on page 304. Step 10 Check the length between the top and bottom horizontal air plenums where the chassis will be installed. The length must be not less than 10.5 inches (267 mm).
Page 323 Air Flow Performance of ONS 15454 M6 Step 11 Install the ONS 15454 M6 empty chassis between the horizontal plenums. Figure 197: Installing the ONS 15454 M6 chassis below the horizontal air plenum Step 12 Return to your originating procedure (NTP).
Page 324 • Six M6 x 20 pan-head Phillips mounting screws • ANSI only: • Six #12-24 x 3/4 pan-head Phillips mounting screws NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 Prerequisite Procedures M6 Shelves, on page 20...
Page 325 (25.4 mm) Statement 1076 Note Make sure that the correct type of 19-inch ANSI rack is used for mounting the ONS 15454 M6 shelf as shown Figure 1: 19-inch ANSI Rack Post Recommended for Cisco ONS 15454 M6 and M2 Shelves, on page...
Page 326 Note During installation, do not use the door to handle the chassis. Note Remove the door from the ONS 15454 M6 shelf and reinstall it after installing all the other modules. Figure 198: Handling the Chassis During Installation Procedure Step 1 Complete the necessary task as applicable: •...
Page 327 DLP-G561 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ANSI Rack Configuration, on page 302 • DLP-G562 Mounting the Brackets on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on page • DLP-G563 Mounting the Air Deflectors (Front-to-Front) on the ONS 15454 M6 Shelf for ETSI Rack Configuration, on page 306 •...
Page 328 Installing the ONS 15454 M6 Shelf DLP-G675 Verify the ONS 15454 M6 Shelf for DC Power Module Installation Figure 199: AC Power Module Installation—Rear Side of the ONS 15454 M6 Shelf Step 2 Loosen the screw and move it to the left position (towards the AC silk-screen text).
Page 329 As needed Required/As Needed Onsite/Remote Onsite Security Level None Caution Use only the fastening hardware provided with the ONS 15454 M6 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material. Cisco ONS 15454 Hardware Installation Guide...
Page 330 DLP-G560 Mounting the Reversible Brackets on the ONS 15454 M6 Shelf for ANSI Rack Configuration Caution When mounting the ONS 15454 M6 in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M6 ship kit, or remove the coating from the threads to ensure electrical continuity.
Page 331 DLP-G560 Mounting the Reversible Brackets on the ONS 15454 M6 Shelf for ANSI Rack Configuration Figure 201: Mounting the Brackets on the ONS 15454 M6 shelf for a 19-inch (482.6-mm) ANSI Configuration The following figure shows mounting the brackets for a 23-inch (584.2-mm) configuration.
Page 332 (Front-to-Back) on the ONS 15454 M6 Shelf for the ANSI rack Configuration, on page 303. Do not mount the left back deflector (exhaust air deflector), if these cards are to be installed in the ONS 15454 M6 shelf: • 100G-LC-C, 10x10G-LC, or CFP-LC •...
Page 333 Installing the ONS 15454 M6 Shelf DLP-G561 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ANSI Rack Configuration Step 6 Insert the screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m).
Page 334 Installing the ONS 15454 M6 Shelf DLP-G562 Mounting the Brackets on the ONS 15454 M6 Shelf for ETSI Rack Configuration Figure 204: Mounting the Brackets with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ANSI Rack Configuration Step 13 Return to your originating procedure (NTP).
Page 335 Caution When mounting the ONS 15454 M6 in a frame with a nonconductive coating (such as paint, lacquer, or enamel) either use the thread-forming screws provided with the ONS 15454 M6 ship kit, or remove the coating from the threads to ensure electrical continuity.
Page 336 Step 4 Place the left front air deflector flush against the left side of the chassis. Do not mount the left front deflector (exhaust air deflector), if these cards are to be installed in the ONS 15454 M6 shelf: Cisco ONS 15454 Hardware Installation Guide...
Page 337 Installing the ONS 15454 M6 Shelf DLP-G564 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration • 100G-LC-C, 10x10G-LC, or CFP-LC • EDRA1-26, EDRA1-35, EDRA2-26, or EDRA2-35 Use the standard brackets directly to mount the ONS 15454 M6 shelf.
Page 338 DLP-G564 Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration Do not mount the left back deflector (exhaust air deflector), if these cards are to be installed in the ONS 15454 M6 shelf: •...
Page 339 Installing the ONS 15454 M6 Shelf DLP-G565 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M6 Shelf for ETSI Rack Configuration Figure 208: Mounting the Bracket with Air Deflectors (Front-to-Back) on the ONS 15454 M6 Shelf for ETSI Rack Configuration Step 13 Return to your originating procedure (NTP).
Page 340 Installing the ONS 15454 M6 Shelf DLP-G565 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M6 Shelf for ETSI Rack Configuration Caution Use only the fastening hardware provided with the ONS 15454 M6 to prevent loosening, deterioration, and electromechanical corrosion of the hardware and joined material.
Page 341 Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M6 Shelf for ETSI Rack Configuration- Front Position, on page 311. Figure 209: Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M6 Shelf for ETSI Rack Configuration- Front Position Step 12...
Page 342 Step 23 Insert M4 flat-head screws and tighten them to a torque value of 11.5 in-lb (1.3 N-m). Figure 210: Mounting the Bracket with Air Deflectors (Front-to-Top) on the ONS 15454 M6 Shelf for ETSI Rack Configuration - Middle Position Step 24 Return to your originating procedure.
Page 343 Installing the ONS 15454 M6 Shelf DLP-G821 Mounting the Bracket with Air Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for ETSI Rack Configuration DLP-G821 Mounting the Bracket with Air Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for ETSI Rack Configuration...
Page 344 Installing the ONS 15454 M6 Shelf DLP-G821 Mounting the Bracket with Air Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for ETSI Rack Configuration Figure 211: Mounting the Bracket with Air Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for ETSI Rack Configuration Step 2 Align the screw holes on the right front air deflector with the screw holes on the right side of the chassis.
Page 345 Installing the ONS 15454 M6 Shelf DLP-G566 Mount the ONS 15454 M6 Shelf on a Rack (One Person) Figure 212: Mounting the Bracket with Air Deflectors (Front-to-Side) on the ONS 15454 M6 Shelf for ETSI Rack Configuration - Middle Position...
Page 346 Note The ONS 15454 M6 requires a minimum of six RU of vertical rack space. To ensure that the mounting is secure, use two to three M6 mounting screws on each side of the shelf. A shelf should be mounted at the bottom of the rack if it is the only unit in the rack.
Page 347 The placement of the shelf is dependent on where you want to install the new equipment in the rack. To ensure proper cooling of the ONS 15454 M6 shelf, make sure that the space in front of the air Note flow vents are free of cables, fibers, and mechanical fixtures for fiber and cable management.
Page 348 Note The ONS 15454 M6 requires a minimum of six RU of vertical rack space. To ensure that the mounting is secure, use two to three M6 mounting screws on each side of the shelf. A shelf should be mounted at the bottom of the rack if it is the only unit in the rack.
Page 349 Note A standard rack can hold six or seven ONS 15454 M6 shelves. When mounting a shelf in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Page 350 Return to your originating procedure (NTP). Front Door The front door of the ONS 15454 M6 provides access to the shelf, fiber-routing tray, fan-tray assembly, and LCD screen. There are two types of front doors that act as protective panels—standard door and deep-front panel. The deep-front panel provides additional space in front of the shelf to accommodate cables that do not fit inside the standard door.
Page 351 ONS 15454 M6 shelf provides improved fiber management. If a standard front door was ordered, the ONS 15454 M6 is shipped with a preinstalled standard door. If a deep-front panel was ordered, a temporary front door is preinstalled on the shelf and the deep-front panel is present in a separate package.
Page 352 Front Door Figure 217: Laser Warning on the ONS 15454 M6 The following figure shows the label that is placed on top of ONS 15454 M6: Figure 218: ONS 15454 M6 Label Figure 219: ONS 15454 M6 Front Door Label...
Page 353 • NTP-G253 Install the ECU or ECU-S Module, on page 349 • NTP-G524 Install the Power Modules in the ONS 15454 M6 Shelf , on page • NTP-G255 Install the LCD Module in the ONS 15454 M6 Shelf, on page •...
Page 354 Installing the ONS 15454 M6 Shelf NTP-G258 Install the Standard Door of the ONS 15454 M6 Shelf Figure 220: Installing the Standard Door Step 2 Align the standard door hinges with the chassis hinges. Step 3 Release the hinge pins.
Page 355 Installing the ONS 15454 M6 Shelf NTP-G258 Install the Standard Door of the ONS 15454 M6 Shelf Figure 221: Mounting the Mechanical Stop Cisco ONS 15454 Hardware Installation Guide...
Page 356 Installing the ONS 15454 M6 Shelf NTP-G258 Install the Standard Door of the ONS 15454 M6 Shelf Figure 222: Retention Feature and Ground Strap Cable—Standard Door Step 9 Place the ground strap cable (see Figure 222: Retention Feature and Ground Strap Cable—Standard Door, on page 326) on the door and the chassis and tighten the nuts to a torque value of 11.5 in-lb (1.3 N-m) to lock the...
Page 357 Stop. You have completed this procedure. NTP-G259 Open and Remove the Standard Door of the ONS 15454 M6 Shelf Purpose This procedure opens and removes the standard door of the ONS 15454 M6 shelf. #2 Phillips Dynamometric screwdriver Tools/Equipment •...
Page 358 Note The ONS 15454 M6 shelf has an ESD plug input and is shipped with an ESD wrist strap. The ESD plug input is located on the outside of the shelf on the left side. It is labeled “ESD” on the top and bottom. Always wear an ESD wrist strap and connect the strap to the ESD plug when working on the ONS 15454 M6.
Page 359 Installing the ONS 15454 M6 Shelf DLP-G576 Open the Standard Door of the ONS 15454 M6 Shelf Figure 224: Opening the Standard Door Step 3 Swing the door open. The retention feature maintains the door in the horizontal position for line card insertion (see the following figure).
Page 360 Purpose This task removes the standard door of the ONS 15454 M6 shelf. Tools/Equipment None Prerequisite Procedures DLP-G576 Open the Standard Door of the ONS 15454 M6 Shelf , on page 328 Required/As Needed As needed Onsite/Remote Onsite Security Level...
Page 361 Installing the ONS 15454 M6 Shelf DLP-G577 Remove the Standard Door of the ONS 15454 M6 Shelf Figure 226: Removing the ONS 15454 M6 Standard Door Step 3 Loosen the screws and slide the mechanical stop to unlock the door.
Page 362 NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf Purpose This procedure installs the deep-front panel of the ONS 15454 M6 shelf. Tools/Equipment 2 Phillips Dynamometric screwdriver Socket (6/32 standard) and socket wrench to tighten or loosen the ground nut...
Page 363 Caution The deep-front panel does not have a hinge and cannot be rotated like a standard door. Rotating the deep-front panel can damage the deep-front panel, shelf hinges, other devices and cables placed below the ONS 15454 M6 shelf. Procedure...
Page 364 Installing the ONS 15454 M6 Shelf NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf c) Route the other end of the ground strap cable outside the shelf at an angle of 180 degrees towards the left. Figure 228: Insert the lug Step 2 Loosen the deep-front panel screws and slide them outwards using the plastic tabs.
Page 365 Installing the ONS 15454 M6 Shelf NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf Figure 229: Placing Deep-Front Panel and Shelf in line Step 4 Align the deep-front panel with the shelf by performing these sub-steps at the same time.
Page 366 Installing the ONS 15454 M6 Shelf NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf Figure 230: Aligning the Deep-Front Panel Pins and Shelf hinges The following figure shows the deep-front panel aligned with the shelf. Cisco ONS 15454 Hardware Installation Guide...
Page 367 Installing the ONS 15454 M6 Shelf NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf Figure 231: Aligning the Deep-Front Panel and Shelf Step 5 Slide the deep-front panel screws inwards using the plastic tabs to engage the retention features and the pins with the shelf notches and hinges (see the following figure).
Page 368 Installing the ONS 15454 M6 Shelf NTP-G327 Install the Deep-Front Panel of the ONS 15454 M6 Shelf Figure 232: Engaging the Deep-Front Panel and Shelf Step 6 Lock the deep-front panel by tightening the screws to a torque value of 6.5 in-lb (0.75 N-m).
Page 369 Caution The deep-front panel does not have a hinge and cannot be rotated like a standard door. Rotating the deep-front panel can damage the deep-front panel, shelf hinges, other devices and cables placed below the ONS 15454 M6 shelf. Note When the deep front-panel is installed, the total chassis depth is 12.9 inches.
Page 370 Installing the ONS 15454 M6 Shelf NTP-G329 Remove the Deep-Front Panel of the ONS 15454 M6 Shelf Figure 234: Removing the end of the ground strap cable Step 2 Loosen the deep-front panel screws and slide them outwards using the plastic tabs to open the deep-front panel as shown in the following figure.
Page 371 Installing the ONS 15454 M6 Shelf NTP-G329 Remove the Deep-Front Panel of the ONS 15454 M6 Shelf Figure 236: Moving the deep-front panel away Step 4 Remove the ground strap cable from the shelf (see the following figure). Figure 237: Removing the ground strap cable a) Loosen the ground nut on the shelf.
Page 372 Stop. You have completed this procedure. External Connection Units The external connection unit (ECU) is a replaceable module placed on top of the ONS 15454 M6 shelf. The ECU module discovers and manages the inventory of the external shelf units. It also handles the multishelf management connections and timing synchronizations.
Page 373 ECU2 The ECU2 is an advanced version of the ECU. The ECU2 is hardware-ready to support IEEE1588v2 PTP, time-of-day (ToD), and pulse-per-second (PPS) inputs. The external connections of ONS 15454 M6 present on the ECU2 are: • 12 remote inventory standard USB connections •...
Page 374 Figure 241: Connectors on ECU-60V Faceplate ECU-S ECU-S is a new type of ECU introduced in Release 10.5.2 for ONS 15454 M6. The ECU-S module also discovers and manages the inventory of the external shelf units. It also handles the multishelf management connections and timing synchronizations.
Page 375 • 1 SCSI with 26 poles for digital I/O signals (on the right-side connector) ECU60-S ECU60-S is a new type of ECU-S introduced for the ONS 15454 M6 when the shelf is powered at –60 VDC nominal input voltage. The ECU60-S module available for the ONS 15454 M6 shelf is 15454 M6-ECU60-S=.
Page 376 MSM ports Craft terminal connection The ONS 15454 M6 ECU60-S supports IEEE1588v2 PTP, time-of-day (ToD), and pulse-per-second (PPS) inputs. The IMPROPRMVL alarm is raised in CTC when the ECU60-S is removed from the ONS 15454 M6 shelf. Note When ONS 15454 M6 is pre-provisioned, or plugged in without the ECU60-S unit, by default, CTC uses the ECU module with the 12 USB 2.0 ports.
Page 377 15454 M6 to support external alarms. The alarm connectors provide dry alarm contacts and are similar to the AIC-I card of the ONS 15454 shelf. The left alarm connector is used for TNC and TNCE relay contact, including Alarm Cut Off (ACO) signal and Digital Input/Output (D-I/O) signals. The right alarm connector is used for Digital Input/Output (D-I/O) signals.
Page 378 USBP_A_1 and Port 1 on the right side of the NCS 2006 ECU-S module is represented as USBP_B_ 1. The left side of the ONS 15454 M6 2006 ECU-S module is Side A and the right side of the ONS 15454 M6 2006 ECU-S module is Side B.
Page 379 NTP-G252 Install the ONS 15454 M6 Shelf , on page 294. • NTP-G259 Open and Remove the Standard Door of the ONS 15454 M6 Shelf , on page 327. • Connect the chassis to the office ground. For detailed instructions on how...
Page 380 Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms. Note If the USB device connected to the ECU module is not detected when the ONS 15454 M6 shelf assembly is powered on, plug out (remove) the ECU module and insert it again. Procedure Step 1 Insert the ECU module in the central slot of the chassis (see the following figure).
Page 381 NTP-G253 Install the ECU or ECU-S Module Figure 244: Installing the ECU module The following figure shows the ECU module installed in the ONS 15454 M6 shelf. Figure 245: ONS 15454 M6 Shelf with ECU module Installed Stop. You have completed this procedure.
Page 382 Do not replace the 15454-M6-DC20, or 15454-M6-DC40 power modules with the 15454-M6-DC V03 power module if the ONS 15454 M6 shelf is consuming more than 960 W of power. Refer to table A-4 to ascertain the power consumption of the shelf.
Page 383 However, during regular operation of the node, the ONS 15454 M6 shelf must have either the 15454-M6-AC or 15454-M6-AC2 power module, but not both. See...
Page 384 Changing the DC Power Module It is possible to change the power modules without powering down the ONS 15454 M6 system. While changing the power modules, ensure that only one power module is replaced at a time and the other power module continues to supply power to the shelf.
Page 385 Procedure Step 1 Complete the necessary task as applicable: • DLP-G569 Install the AC Power Module in the ONS 15454 M6 Shelf, on page 355 • DLP-G757 Replacing 15454-M6-AC With 15454-M6-AC2 Power module, on page 358 • DLP-G758 Replacing 15454-M6-AC2 With 15454-M6-AC Power module, on page 359 •...
Page 386 Caution The node can temporarily work with both 15454-M6-AC and 15454-M6-AC2 power module units installed on the ONS 15454 M6 shelf. However, during regular operation, the shelf must have either the 15454-M6-AC or 15454-M6-AC2 power module, but not both. Insert the AC power module in Slot A or Slot B, or both (see the following figure).
Page 387 For redundant power supplies, two AC power modul5es can be installed in Slot A and Slot B. Note However, only one power module can sustain the functioning of the entire ONS 15454 M6 system. In that case, insert a power filler module in the empty slot (for example, see...
Page 388 Caution Always use the supplied ESD wristband when working with a powered ONS 15454 M6. For detailed instructions on how to wear the ESD wristband, see the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.
Page 389 370. Note While replacing power modules, when the ONS 15454 M6 chassis is in the mixed power mode (with both 15454-M6-AC and 15454-M6-AC2 power modules installed), do not provision or install any line cards. Card provisioning and installation must be done only after both the slots have the same type of power modules.
Page 390 DLP-G570 Install the DC Power Module in the ONS 15454 M6 Shelf Caution Always use the supplied ESD wristband when working with a powered ONS 15454 M6. For detailed instructions on how to wear the ESD wristband, see the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.
Page 391 DLP-G570 Install the DC Power Module in the ONS 15454 M6 Shelf Caution While changing the power modules from 15454-M6-DC20 to 15454-M6-DC and vice-versa, the ONS 15454 M6 shelf can temporarily work with both 15454-M6-DC and 15454-M6-DC20 power modules installed.
Page 392 For redundant power supplies, two DC power modules can be installed in Slot A and Slot B. However, Note only one power module can sustain the functioning of the entire ONS 15454 M6 system. In that case, insert a power filler module in the empty slot (see the following figure).
Page 393 Figure 250: Installing a Power Filler Module Step 4 Return to your originating procedure (NTP). When the ONS 15454 M6 shelf is powered at –60 VDC (nominal), only the TNC, OPT-AMP-C, Note OPT-AMP-17-C, OPT-EDFA-17, and OPT-EDFA-24 cards, and the 15454-M6-ECU-60 can be installed.
Page 394 The 15454-M6-DC40 power module uses 15454-M6-DCCBL2-L= and 15454-M6-DCCBL2-R= cables. Note Do not replace the 15454-M6-DC with the 15454-M6-DC20 power module if the ONS 15454 M6 shelf is consuming more than 960 W of power. Refer to Power Calculation, on page 478 to ascertain the power consumption of the shelf.
Page 395 Caution Always use the supplied ESD wristband when working with a powered ONS 15454 M6. For detailed instructions on how to wear the ESD wristband, see the Electrostatic Discharge and Grounding Guide for Cisco CPT and...
Page 396 There are three alarm LEDs (CRIT, MAJ, and MIN) on the LCD unit that indicate whether a critical, major, or minor alarm is present anywhere on the ONS 15454 M6 shelf. The shelf controller card controls the conditions that result in triggering the LEDs. The LEDs can be overwritten by the shelf controller card (TNC, TNCE, TSC, or TSCE) in all the three states (OFF/red/green).
Page 397 Installing the ONS 15454 M6 Shelf NTP-G255 Install the LCD Module in the ONS 15454 M6 Shelf Required/As Needed Required Onsite/Remote Onsite Security Level None Note If the LCD unit is removed from the shelf, wait for at least 5 seconds before plugging it back into the shelf.
Page 398 For redundant AC power feeds, install both the AC power modules and use the two power cables (right and left cables) shipped with the ONS 15454 M6 and one ground cable. For an AC power supply, the fuse rating must not exceed 10A, 15A, or 20A. For North America, the branch circuit protection must be rated 20A. The overcurrent/short circuit protection must be in accordance with local and national electrical codes.
Page 399 DC power module. For redundant DC power feeds, install both the DC power modules and use the two power cables shipped with the ONS 15454 M6 and one ground cable. For a DC power supply, the fuse rating must not exceed 40A.
Page 400 • Two-hole grounding lug, shipped with the ONS 15454 M6 Prerequisite Procedures • NTP-G524 Install the Power Modules in the ONS 15454 M6 Shelf , on page 355. • Connect the chassis to the office ground. For detailed instructions on how...
Page 401 Installing the ONS 15454 M6 Shelf NTP-G256 Install Power and Ground to the ONS 15454 M6 Shelf Warning Blank faceplates (filler panels) serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment;...
Page 402 Statement 1028 Caution Always use the supplied ESD wristband when working with a powered ONS 15454 M6. For detailed instructions on how to wear the ESD wristband, see the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.
Page 403 DLP-G571 Connect Office Power (AC) to the ONS 15454 M6 Shelf Step 3 Connect the office ground to the ONS 15454 M6 shelf. For detailed instructions on grounding, see the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.
Page 404 Procedure Step 1 Verify that the AC power module is installed in Slot A or Slot B (or both) of the ONS 15454 M6. Step 2 Attach the AC power cable to the cable connector in the AC power module (see the following figure).
Page 405 Installing the ONS 15454 M6 Shelf DLP-G571 Connect Office Power (AC) to the ONS 15454 M6 Shelf Figure 253: Connecting Office Power—AC Power Modules Step 3 Close the cable clip to secure the power cable (see the following figure). Figure 254: Cable Clip to Secure the Power Cable For Slot A power module, the power cable exits from the left side.
Page 406 Installing the ONS 15454 M6 Shelf DLP-G571 Connect Office Power (AC) to the ONS 15454 M6 Shelf Figure 255: Power Cable Exit Step 4 Connect the power cable to the fuse panel or power source. The voltage rating value for AC power ranges between 100 VAC to 240 VAC depending on the Note standards in various countries.
Page 407 Installing the ONS 15454 M6 Shelf DLP-G572 Connect Office Power (DC) to the ONS 15454 M6 Shelf (ANSI Only) Cable AC power cable - ARG left exit 15454-M-CBL-LARG= AC power cable - ARG right exit 15454-M-CBL-RARG= AC power cable - AUS left exit...
Page 408 Statement 1075 Caution The ONS 15454 M6 relies on the protective devices in the building installation to protect against short circuit, overcurrent, and ground faults. Ensure that the protective devices are properly rated and comply with national and local codes.
Page 409 Crimp the lugs onto the ends of all the power leads. Step 7 Verify that the DC power module is installed in Slot A or Slot B (or both) of the ONS 15454 M6 shelf. Step 8 Remove the terminal block protective covers from the DC power modules (see the following figure).
Page 410 Installing the ONS 15454 M6 Shelf DLP-G572 Connect Office Power (DC) to the ONS 15454 M6 Shelf (ANSI Only) Figure 257: Connecting Office Power—DC Power Modules (ANSI Only) Step 10 Insert the lugs as shown in the above figure. The top cable is for RET and the bottom cable is for –48 V/–60 Step 11 Insert the lock washers and nuts to the terminal block.
Page 411 Installing the ONS 15454 M6 Shelf DLP-G573 Connect Office Power (DC) to the ONS 15454 M6 Shelf (ETSI Only) Figure 258: Connecting Office Power—DC Power Modules (ANSI Only) Caution Before you make any crimp connections, coat all bare conductors (battery, battery return, and frame ground) with an appropriate antioxidant compound.
Page 412 Network Time Protocol/Simple Network Time Protocol (NTP/SNTP) server, you must reset the ONS 15454 M6 clock. After powering down, the date defaults to January 1, 1970, 00:04:15. To reset the clock, see the “NTP-G24 Setting Up Node Identification Information” procedure in the Cisco ONS 15454 DWDM Control Card and Node Configuration Guide.
Page 413 DLP-G573 Connect Office Power (DC) to the ONS 15454 M6 Shelf (ETSI Only) Step 2 Verify that the DC power module is installed in Slot A or Slot B (or both slots) of the ONS 15454 M6. Step 3 Unscrew the screws to a torque value of 4 in-lb (0.45 N-m) to remove the protective covers from the DSUB power connector of the DC power modules (see the following figure).
Page 414 Installing the ONS 15454 M6 Shelf DLP-G573 Connect Office Power (DC) to the ONS 15454 M6 Shelf (ETSI Only) Figure 260: Connecting Office Power—DC Power Modules (ETSI Only) Note For slot A power module, use the left power cable—15454-M6-DCCBL-LE, and for slot B use the right power cable—15454-M6-DCCBL-RE.
Page 415 To power up the node, insert the fuse into the fuse position according to site practice. The fuse rating must not exceed 20A. Step 2 If the ONS 15454 M6 does not power up, check the voltage at the power source using a voltmeter. The voltage should be 100 to 240 VAC +/-10 percent. Step 3 Return to your originating procedure (NTP).
Page 416 Installing the ONS 15454 M6 Shelf DLP-G575 Turn On and Verify DC Office Power on the ONS 15454 M6 Shelf DLP-G575 Turn On and Verify DC Office Power on the ONS 15454 M6 Shelf Purpose This task turns on the power and verifies correct power and returns on the ONS 15454 M6 shelf.
Page 417 LED is OFF. When the power line is connected and if there is no TNC, TNCE, TSC, or TSCE card installed in the ONS 15454 M6 shelf, then the LED is OFF. A red LED indicates an alarm in the fan-tray assembly. A green LED indicates that the fan-tray assembly is functioning, the power line is connected, and the power module is functioning properly.
Page 418 None Note The 15454-M2-FTA2 is compatible with R9.2.0 and later releases. Caution Do not operate an ONS 15454 M6 without an air filter. For information on the air filter, see NTP-G114 Inspect and Replace the Air Filter, on page 435.
Page 419 To install the fan-tray assembly, it is not necessary to move any of the fiber-routing facilities. Procedure Step 1 Insert the fan-tray assembly inside the left slot (fan tray slot) of the ONS 15454 M6 chassis (see the following figure). Figure 261: Installing the Fan-Tray Assembly Step 2 Push the fan-tray assembly such that the backplane connector is engaged completely.
Page 420 Default Module The ONS 15454 M6 chassis is shipped with the fiber module installed. If you need to use CAT5 cables instead of optical fibers, you can replace the fiber module with the cable module.
Page 421 Cable and Fiber Routing Cable and fiber routing accommodates all the high-density cards for line card connections in ONS 15454 M6. The exit of the fibers and cables is split into two channels. The line card from slot 1 to 4 exits from the lower right side, and the line card from 5 to 8 exit from the upper right side.
Page 422 None Procedure Step 1 Loosen the screws on the fiber module present on the right side of the ONS 15454 M6 assembly. (See the following figure.) Step 2 Loosen the screw present on the air filter locking feature of the ONS 15454 M6 shelf.
Page 423 DLP-G654 Install the Cable Module Figure 264: Removing the Fiber module DLP-G654 Install the Cable Module Purpose This procedure installs the cable module in the ONS 15454 M6 system. Tools/Equipment Phillips cross-head PH screwdriver #1 Prerequisite Procedures DLP-G653 Remove the Fiber Module, on page 392...
Page 424 Installing the ONS 15454 M6 Shelf DLP-G655 Route and Lock Cables Figure 265: Installing the Cable Module DLP-G655 Route and Lock Cables Purpose This procedure routes and locks the cables on the ONS 15454 M6 system. Tools/Equipment None None Prerequisite Procedures...
Page 425 Installing the ONS 15454 M6 Shelf DLP-G655 Route and Lock Cables Figure 266: ECU module Cable Routing Figure 267: Cable Management Step 2 Fix the cables using the tie-wrap provided in the accessories kit. Step 3 To route the optical patch cords or copper cables, do the following as necessary: a) Route the optical patch cords from the line cards through the fiber or cable module as shown in the following figure.
Page 426 Installing the ONS 15454 M6 Shelf DLP-G655 Route and Lock Cables Figure 268: Cable Routing b) Remove the front door and connect the copper cables to the SFP or RJ-45 ports of the cards.Do not route the copper cables from the SFPs or RJ-45 ports through the fiber or cable module.
Page 427 Installing the ONS 15454 M6 Shelf NTP-G312 Attach Wires to Alarm, Timing, LAN, and Craft Pin Connections in Cisco ONS 15454 M6 Figure 269: Sequence to Remove the Power Module Step 5 Return to your originating procedure (NTP). NTP-G312 Attach Wires to Alarm, Timing, LAN, and Craft Pin...
Page 428 Security Level None Caution Always use the supplied ESD wristband when working with a powered ONS 15454 M6. For detailed instructions on how to wear the ESD wristband, see the Electrostatic Discharge and Grounding Guide for Cisco CPT and Cisco ONS Platforms.
Page 429 Installing the ONS 15454 M6 Shelf DLP-G295 Install Alarm Wires in ONS 15454 M6 Tools/Equipment Alarm SCSI 26-pin cable Wire-wrap tool for ANSI BITS Screw for the alarm cable Prerequisite Procedures NTP-G253 Install the ECU or ECU-S Module, on page 349.
Page 430 Installing the ONS 15454 M6 Shelf DLP-G295 Install Alarm Wires in ONS 15454 M6 Figure 270: Installing the ECU Alarm Cable—Left Exit Option Figure 271: Installing the ECU Alarm Cable—Right Exit Option Table 36: SCSI Alarm Cable (15454-M-ALMCBL) and SCSI Alarm Patch Cable (15454-M-AEXPCBL) Connector Details...
Page 431 Installing the ONS 15454 M6 Shelf DLP-G295 Install Alarm Wires in ONS 15454 M6 Pin Number Color Code Input Alarms - Right Alarm Connector Input-Output Alarms - Left Connector Black/Orange Input Pair #3 + Critical Audible Alarm + Black/Yellow Input Pair #4 +...
Page 432 Installing the ONS 15454 M6 Shelf DLP-G295 Install Alarm Wires in ONS 15454 M6 Pin Number Color Code Input Alarms - Right Alarm Connector Input-Output Alarms - Left Connector Black/Red Input Pair #2 + Major Audible Alarm + — —...
Page 433 DLP-G296 Install Timing Wires on ONS 15454 M6 - ANSI DLP-G296 Install Timing Wires on ONS 15454 M6 - ANSI Purpose This task installs the timing cables on the ONS 15454 M6 ECU module for ANSI. Tools/Equipment Wire-wrap tool and 100-ohm wire-wrap cable.
Page 434 Step 4 Return to your originating procedure (NTP). DLP-297 Install Timing Wires in ONS 15454 M6 - ETSI This task installs the timing cables on the ONS 15454 M6 ECU module for ETSI. Purpose Tools/Equipment 75-ohm coaxial cable with a DIN-1.0/2.3 miniature coaxial connector. The PID...
Page 435 Installing the ONS 15454 M6 Shelf DLP-297 Install Timing Wires in ONS 15454 M6 - ETSI module ETSI BITS connectors. Figure 275: ECU module ETSI BITS Connectors Cabling, on page 405 shows cable routing of ECU module ETSI BITS connectors. The following table lists the pin assignments on the ECU module.
Page 436 275. c) Slide the coupling sleeve forward to lock the cable connector to the ECU module connector. See diagram3 Figure 174: Cisco ONS 15454 M6 Shelf Dimensions for an ETSI Rack Configuration, on page 275. To unlock the cable connector from the ECU module connector, hold the connector and slide Note the coupling sleeve backward.
Page 437 Installing the ONS 15454 M6 Shelf NTP-G308 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves Tools/Equipment Standard CAT-5 Ethernet cable (straight-through for data terminating equipment [DTE] or cross-over for data circuit-terminating equipment [DCE]) or RJ-45 connector Crimping tool for RJ-45 connector 0.51 mm²...
Page 438 Plug the other connector to any one of the MSM ports of the ONS 15454 M6 SSCs in the next layer. c) Repeat a and b to connect the remaining MSM ports of the ONS 15454 M6 in the first layer to the next layer.
Page 439 Step 1 Complete the necessary task as applicable: • To connect the ONS 15454 M6 as the node controller and ONS 15454 or ONS 15454 M6 as subtending shelves with Catalyst 3560, complete the DLP-G682 Connect the ONS 15454 M6 as the Node Controller in a Mixed Multishelf Configuration Using the Catalyst 3560, on page 410.
Page 440 ECU module and MSM ports, see the External Connection Units, on page 342. Note Use the craft terminal port or the EMS port present on the ECU module to connect the ONS 15454 M6 node controller to the LAN. Cisco ONS 15454 Hardware Installation Guide...
Page 441 Installing the ONS 15454 M6 Shelf DLP-G682 Connect the ONS 15454 M6 as the Node Controller in a Mixed Multishelf Configuration Using the Catalyst 3560 Procedure Step 1 Using a cross-over (CAT-5) LAN cable: a) Plug one connector into Port 1 of the working Catalyst 3560.
Page 442 Installing the ONS 15454 M6 Shelf DLP-G682 Connect the ONS 15454 M6 as the Node Controller in a Mixed Multishelf Configuration Using the Catalyst 3560 Figure 277: Mixed Multishelf Configuration with the ONS 15454 M6 as the Node Controller Cisco ONS 15454 Hardware Installation Guide...
Page 443 ECU module and MSM ports, see the External Connection Units, on page 342. Note Use the craft terminal port or the EMS port present on the ECU module to connect the ONS 15454 M6 node controller to the LAN. Procedure Step 1...
Page 444 TNC/TNCE/TSC/TSCE card in Slot 1. c) Repeat Step 1a and Step 1b to connect the remaining MSM ports on the node controller ONS 15454 M6 shelf to the MSM ports on the subtending ONS 15454 M6 shelf.
Page 445 Installing the ONS 15454 M6 Shelf DLP-G683 Connect the ONS 15454 as the Node Controller in a Mixed Multishelf Configuration Figure 278: Mixed Multishelf Configuration without a Catalyst Switch Using ONS 15454 M6 as the Node Controller Step 4 Return to your originating procedure (NTP).
Page 446 342. Note This procedure explains the steps to connect the ONS 15454 multishelf node and subtending shelves to a 24-port Catalyst 2950 or Catalyst 3560 switch. Follow the steps provided in this procedure to connect the multishelf node to the 48-port Catalyst 2950 or Catalyst 3560 switch.
Page 447 DLP-G683 Connect the ONS 15454 as the Node Controller in a Mixed Multishelf Configuration • • Plug one connector into the MSM port of the subtending ONS 15454 M6 shelf that corresponds to the TNC/TNCE/TSC/TSCE card in Slot 8. • Plug the other connector into Port 2 of the standby Catalyst 3560.
Page 448 Installing the ONS 15454 M6 Shelf DLP-G683 Connect the ONS 15454 as the Node Controller in a Mixed Multishelf Configuration Figure 279: Mixed Multishelf Configuration with the ONS 15454 as the Node Controller Step 7 Return to your originating procedure (NTP).
Page 449 To configure the Catalyst 2950 switch using IOS commands, complete the NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby) for a ONS 15454 Multishelf Node, on page 152 Step 3 To configure the Catalyst 3560 switch using IOS commands, complete the...
Page 450 Onsite/Remote Security Level None Note Use TCC3 cards in ONS 15454 node controller while connecting it to the ONS 15454 M6 subtending shelves and when there are more than 12 subtending shelves. Procedure Step 1 Disconnect the subtending shelf at Port 21 of the active and standby Catalyst 2950: a) Remove the cross-over (CAT 5) LAN cable from Port 21 of the active Catalyst 2950.
Page 451 • Plug the other connector into Port 2 of the standby Catalyst 3560. Step 4 Repeat Step 3a and Step 3b to connect additional ONS 15454 subtending shelves using Port 3 through Port 20 on the Catalyst 3560 switches. Step 5...
Page 452 Step 6 To configure the Catalyst 3560 (extended) using IOS commands, complete the NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby) for a ONS 15454 Multishelf Node, on page 152. Step 7 Return to your originating procedure (NTP).
Page 453 Use TCC3 cards in ONS 15454 node controller while connecting it to the ONS 15454 M6 subtending shelves and when there are more than 12 subtending shelves. Note The CTC in ONS 15454 M6 shelf view displays the three ports of the MS-ISC card, and EMS and circuit ports present on the ECU. Procedure...
Page 454 • Plug the other connector into Port 2 of the standby Catalyst 3560. Step 4 Repeat Step 3a and Step 3b to connect additional ONS 15454 shelves using Port 3 to Port 24 on the Catalyst 3560 switches. Step 5...
Page 455 Step 6 To configure the Catalyst 3560 (extended) using IOS commands, complete the NTP-G298 Configure a Cisco Catalyst 2950 or Catalyst 3560 (Active and Standby) for a ONS 15454 Multishelf Node, on page 152. Step 7 Return to your originating procedure (NTP).
Page 456 Onsite Security Level None Procedure Step 1 If you installed an ONS 15454 M6, complete the following table by verifying that each applicable procedure was completed. Table 40: ONS 15454 M6 Shelf —ETSI Rack Installation Task Summary Description Completed NTP-G305 Unpack and Inspect the ONS 15454, ONS 15454 M2, and ONS 15454 M6 Shelves,...
Page 457 DLP-G578 Inspect the ONS 15454 M6 Shelf Installation and Connections Description Completed NTP-G258 Install the Standard Door of the ONS 15454 M6 Shelf , on page 323 Note The ECU module, power modules, LCD and the fan-tray assembly can be installed in any order.
Page 458 Installing the ONS 15454 M6 Shelf NTP-G317 Connect the ONS 15454 M6 Multishelf Node and the ONS 15454 M6 Subtending Shelves with Simplex Controllers Security Level None Caution Do not apply power to the shelf until you complete all installation steps.
Page 459 Step 2 Repeat Step 1 to connect the remaining two MSM ports of the ONS 15454 M6 shelf, used as the node controller, to the subsequent subtending ONS 15454 M6 shelf assemblies. You can connect up to a maximum of 3 SSCs in the multishelf configuration.
Page 460 Using a cross-over (CAT-5) LAN cable: a) Plug one connector to any one of the remaining MSM ports of the ONS 15454 M6 SSCs in the first layer. b) Plug the other connector to any one of the MSM ports of the ONS 15454 M6 SSCs in the next layer.
Page 461 Stop. You have completed this procedure. Air Deflector An air deflector is a sheet-metal part that is mounted on the ONS 15454 M6 shelf to orient the air flow in a specific direction. Air deflectors can be mounted in different positions to control the air flow: •...
Page 462 Air Filter The ONS 15454 M6 contains a preinstalled reusable air filter (15454 M6-FTF) on the right side of the shelf. The reusable filter is made up of a gray, open-cell, polyurethane foam that is specially coated to provide fire and fungi resistance.
Page 463 Provisioning > General > Voltage/Temperature pane. Cooling Profile The cooling profile feature allows you to control the speed of the fans in the ONS 15454 M6 shelf depending on the I/O cards used. CTC allows you to choose a cooling profile for ONS 15454 M6 shelf. You can change the cooling profile in Shelf view >...
Page 464 Installing the ONS 15454 M6 Shelf Cooling Profile Table 41: Cooling Profile Values for ONS 15454 M6 Cards Cards with Low Cooling Profile Cards with Medium Cooling Profile Cards with High Cooling Profile • 32-WSS • 10GE-XP • 100G-LC-C • 32-WSS-L •...
Page 465 C H A P T E R Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf This chapter explains how to maintain the ONS 15454 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 shelf installations. Note Unless otherwise specified, “ONS 15454”...
Page 466 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G114 Inspect and Replace the Air Filter Tools/Equipment New air filter, pinned hex key tool Prerequisite Procedures None Required/As Needed As needed Onsite/Remote Onsite...
Page 467 If the front door is already open, proceed to Step 3. a) Open the front door lock. The ONS 15454 comes with a pinned hex key for locking and unlocking the front door. Turn the key counterclockwise to unlock the door and clockwise to lock it.
Page 468 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G114 Inspect and Replace the Air Filter Figure 288: ETSI Shelf Fan-Tray Air Filter in an External Filter Bracket (Front Door Removed) Step 4 Push the outer side of the handles on the fan-tray assembly to expose the handles.
Page 469 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf Assembly Step 13 If you removed the door, complete the NTP-G40 Replace the Front Door , on page 448.
Page 470 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G274 Replace the Air Filter of the ONS 15454 M2 Shelf Assembly Figure 289: Replacing the Air Filter Air filter Screw Step 2 Extract the air filter from the shelf assembly as shown in the following figure.
Page 471 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly Figure 291: Replacing the Air Filter Step 4 Replace the air filter with a new one if the air filter is dirty or clogged with dust.
Page 472 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly Note The air filters are single-use only. They must not be cleaned and reused. This is a Telcordia NEBS requirement, GR-63-CORE Issue 4.
Page 473 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G262 Replace the Air Filter of the ONS 15454 M6 Shelf Assembly Figure 293: Extracting the Air Filter Step 5 Replace the air filter with a new one if the air filter is dirty or clogged with dust.
Page 474 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G263 Replace the Air Filter of the AC Power Module in the ONS 15454 M6 Shelf Assembly Stop. You have completed this procedure. NTP-G263 Replace the Air Filter of the AC Power Module in the...
Page 475 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G115 Clean Fiber Connectors Figure 295: Replacing the Air Filter—AC Power Module Step 4 Replace the air filter with a new one if the air filter is dirty or clogged with dust.
Page 476 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf DLP-G261 Clean Multi Fiber-Optic Cable Connectors Security Level None Warning Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not view directly with optical instruments.
Page 477 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf DLP-G262 Clean Fiber Connectors with CLETOP Step 2 Read the manufacturer (cleaning cartridge) instructions to insert the connector into the cleaning cartridge. Step 3 Slide the lever on the cartridge to swipe the connector surface.
Page 478 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G40 Replace the Front Door Prerequisite Procedures None Required/As Needed Required Onsite/Remote Onsite Security Level None Procedure Step 1 Remove the dust plug from the fiber adapter.
Page 479 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G40 Replace the Front Door Figure 296: Installing the Door Ground Strap Retrofit Kit Step 3 (ANSI only) Attach the other end of the ground strap to the longer screw on the fiber guide.
Page 480 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly Figure 297: Shelf Assembly with Door Ground Strap Retrofit Kit Installed (ANSI) Step 6 Swing the door closed and lock the door with the provided pinned-hex key.
Page 481 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly Security Level None Caution The 15454-FTA3 fan-tray assembly can only be installed in ONS 15454 R3.1 and later shelf assemblies (15454-SA-ANSI, P/N: 800-19857;...
Page 482 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly NEBS3E or NEBS3 — None NEBS3E or NEBS3 — MEA on 10G NEBS3E or NEBS3 —...
Page 483 Step 4. a) Open the front door lock. The ONS 15454 comes with a pinned hex key for locking and unlocking the front door. Turn the key counterclockwise to unlock the door and clockwise to lock it. b) Press the door button to release the latch.
Page 484 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly Figure 298: Removing or Replacing the Fan-Tray Assembly (Front Door Removed) (ANSI) The following figure shows the location of the fan tray on the ONS 15454 ETSI shelf.
Page 485 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G116 Replace the Fan-Tray Assembly of the ONS 15454 Shelf Assembly Figure 299: Removing or Replacing the Fan-Tray Assembly (Front Door Removed) (ETSI) Step 8 If you are replacing the fan-tray air filter and it is installed beneath the fan-tray assembly, slide the existing air filter out of the shelf assembly and replace it before replacing the fan-tray assembly.
Page 486 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G272 Replace the Fan-Tray Assembly of the ONS 15454 M2 Shelf Assembly NTP-G272 Replace the Fan-Tray Assembly of the ONS 15454 M2 Shelf Assembly...
Page 487 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G272 Replace the Fan-Tray Assembly of the ONS 15454 M2 Shelf Assembly Step 2 Extract the fan-tray assembly partially to disconnect the backplane connector and wait until the fan stops (see...
Page 488 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G260 Replace the Fan-Tray Assembly of the ONS 15454 M6 Shelf Assembly NTP-G260 Replace the Fan-Tray Assembly of the ONS 15454 M6 Shelf Assembly...
Page 489 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G260 Replace the Fan-Tray Assembly of the ONS 15454 M6 Shelf Assembly Figure 303: Extract the Fan-Tray Assembly Step 4 Extract the fan tray partially using the handle in order to disconnect the backplane connector and wait until...
Page 490 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G117 Replace the ANSI Shelf Alarm Interface Panel Figure 305: Fan-Tray Extracted Step 6 Slide the new fan-tray into the shelf assembly until the electrical plug at the rear of the tray plugs into the corresponding receptacle on the backplane.
Page 491 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G117 Replace the ANSI Shelf Alarm Interface Panel Caution Do not use a 2A AIP with a 5A fan-tray assembly; doing so will cause a blown fuse on the AIP.
Page 492 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G117 Replace the ANSI Shelf Alarm Interface Panel The type of shelf that the AIP resides in determines the version of AIP that should replace the failed Caution AIP.
Page 493 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G118 Replace the ANSI Shelf Plastic Lower Backplane Cover The CTC session freezes until all circuits are repaired. Circuit repair can take up to five minutes or Note more depending on the number of circuits provisioned.
Page 494 NTP-G795 Change System Mode Using LCD For ONS 15454 M2 and 15454 M6, the system mode can be changed from ANSI (SONET) to ETSI (SDH) or vice-versa. Changing the system mode removes the provisioned data and the system reverts to the default configuration.
Page 495 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G795 Change System Mode Using LCD This is available on the single controller and dual controller cards. The node can be in a standalone or multishelf configuration.
Page 496 Maintaining the ONS 15454 M12 (ANSI and ETSI), ONS 15454 M2 and ONS 15454 M6 Shelf NTP-G795 Change System Mode Using LCD Cisco ONS 15454 Hardware Installation Guide...
Page 497 The TCC2P card can be used as a control card in a subtended shelf where the node controller is TCC3 card on ONS 15454 chassis or TNC/TNCE/TNCS/TNCS-O cards on ONS 15454 M6 or NCS 20015 chassis. The TCC2P card can also be used as a node controller in a stand-alone configuration.
Page 498 • Total bandwidth: 240 Gbps • Data plane bandwidth: 160 Gbps • SONET/SDH plane bandwidth: 80 Gbps Configurations The ONS 15454 can be configured for these dense wavelength division multiplexing (DWDM) topologies: • Hubbed rings • Multihubbed rings • Point-to-point •...
Page 499 • BNC: Trompeter #UCBJ224 75-ohm 4 leg connector (King or ITT are also compatible) • AMP Champ: AMP#552246-1 with #552562-2 bail locks BITS Interface (ANSI only) The ONS 15454 building integrated timing supply (BITS) interface has these specifications: • 2 DS-1 BITS inputs • 2 derived DS-1 outputs •...
Page 500 C-Temp: 32 to +131 degrees Farenheit (0 to +55 degrees Celsius) I-Temp: –40 to +139 degrees Farenheit (–40 to +65 degrees Celsius) • Operating humidity: 5 to 95 percent, noncondensing The ONS 15454 ETSI has the following environmental specifications: Cisco ONS 15454 Hardware Installation Guide...
Page 501 The ONS 15454 M2 has these bandwidth specifications (depending on the applications): • Total bandwidth: 200 Gbps • Data plane bandwidth: 100 Gbps per slot Configurations The ONS 15454 M2 can be configured for these dense wavelength division multiplexing (DWDM) topologies: • Hubbed rings • Multihubbed rings • Point-to-point •...
Page 502 Alarm Interface The ONS 15454 M2 does not support alarm interface. Passive Unit Remote Inventory The ONS 15454 M2 provides 1 standard USB port located on the power module to retrieve the passive units inventory data. BITS Interface The ONS 15454 M2 building integrated timing supply (BITS) interface has these specifications: •...
Page 503 Hardware Specifications System Power The ONS 15454 M2 for ETSI has the following system timing specifications: • Stratum 3, per ITU-T G.813 • Free running accuracy: +/- 4.6 ppm • Holdover stability: 3.7 exp -7 per day, including temperature (< 255 slips in first 24 hours) •...
Page 504 The ONS 15454 M6 has the following bandwidth specifications (depending on the applications): • Total bandwidth: 600 Gbps • Data plane bandwidth: 100 Gbps per slot Configurations The ONS 15454 M6 can be configured for the following dense wavelength division multiplexing (DWDM) topologies: • Hubbed rings • Multihubbed rings •...
Page 505 • Control outputs: Open contact maximum 60 VDC, closed contact maximum 100 mA Passive Unit Remote Inventory The ONS 15454 M6 provide 12 standard USB ports located on the ECU or ECU2 to retrieve the inventory data from the passive units.
Page 506 • Fuse rating for an AC power supply must not exceed 10 A, 15 A, or 20 A depending on the standard in various countries. For North America, the branch circuit protection must be rated 20 A. The following table lists power specifications of the AC power modules for the ONS 15454 M6 shelf. Table 46: ONS 15454 M6 AC Power Specifications...
Page 507 –50 to –72 VDC Note When the ONS 15454 M6 shelf is powered at –60 VDC (nominal), only these cards can be installed: TNC, OPT-AMP-C, OPT-AMP-17-C, OPT-EDFA-17, OPT-EDFA-24, 17 SMR9 FS, 24 SMR9 FS, 34 SMR9 FS, SMR20 FS, SMR20 FS CV, 12-AD-FS, 16-AD-FS, 100GS-CK-LC, MR-MXP cards, and the 15454-M6-ECU-60 card.
Page 508 The reserved power for the ONS 15454 M6 shelf with a TNC or TNC-E controller card is 284 W, and for the TSC or TSC-E controller card it is 270 W.
Page 509 15454-M6-FTA 15454-M6-FTA2 System Environmental Specifications The ONS 15454 M6 for ANSI environment has these specifications: • Operating temperature: 23 to +131 degrees Farenheit (-5 to +55 degrees Celsius) • Operating humidity: 5 to 95 percent, noncondensing The ONS 15454 M6 for ETSI environment has these specifications: •...
Page 510 Hardware Specifications Dimensions Cisco ONS 15454 Hardware Installation Guide...
Page 511 See AIP fiber management 158, 173 450, 469 alarms installing alarm cables 101, 106 incompatibility alarms 104, 109 installing timing cables interface specifications installing TL1 craft interface cables AMP champ Cisco ONS 15454 Hardware Installation Guide IN-1...
Page 512 71, 244, 249, 377, 381 resetting do not use backplane pins simultaneously closing Electrostatic Discharge and Grounding Guide for Cisco Cisco CPT and FMEC cover Cisco ONS Platforms 57, 66, 68, 70, 71, 74, 100, 131, 194, 216, coating bare power conductors...
Page 513 45, 57, 58, 215, 219, 220, 320, 328, 330, 448 FlexLayer modules description FlexLayer shelf installing ground strap retrofit kit FMEC cover 45, 215, 320 label (ANSI) front door ground strap retrofit kit 57, 219, 328 opening Cisco ONS 15454 Hardware Installation Guide IN-3...
Page 514 71, 146, 244, 268, 377, 427 measuring ONS 15454 71, 244, 377 fuse and alarm cables 146, 268, 427 voltage mesh patch-panel tray office power. See power 68, 239, 370 MIC-A/P FMEC 66, 70, 101 description Cisco ONS 15454 Hardware Installation Guide IN-4...
Page 515 18, 65, 158 installation overview (ANSI) 177, 272 fiber management installation overview (ETSI) 27, 179, 274 FMEC slots mount a single node (ANSI) 26, 179, 273 requirements mount multiple nodes (ANSI) 26, 274 Cisco ONS 15454 Hardware Installation Guide IN-5...
Page 516 EIA/TIA-232 port connection 126, 129, 130 Y-cable modules interface specifications installing modules 129, 130 pin assignments installing the tray TNC card 261, 265, 266 Y-cable protection configuring UDC and VoIP managing fibers installing Cisco ONS 15454 Hardware Installation Guide IN-6...

Cisco ONS 15454 Hardware Installation Manual

CHAPTER 3 Installing the ONS 15454 M12 (ANSI and ETSI) Shelf

CHAPTER 4 Installing the ONS 15454 M2 Shelf

CHAPTER 5 Installing the ONS 15454 M6 Shelf

Quick Links

Related Manuals for Cisco ONS 15454

Summary of Contents for Cisco ONS 15454