Advertisement
Quick Links
Homologation Kit
Groundsmaster
Model No. 31950
Installation
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure
1
2
3
4
5
6
1
Preparing the Machine
No Parts Required
Procedure
1.
Connect the machine to the tow vehicle; refer to
the Operator's Manual for the machine.
2.
Lower the mower decks; refer to the Operator's
Manual for your machine.
3.
Engage the parking brake for the tow vehicle,
shut off the engine, remove the key, and wait
for all moving parts to stop before leaving the
operator's seat.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
1200 Series Pull Behind Rotary Mower
Description
No parts required
Left taillight support
Right taillight support
Reflector triangle
Screw (#10-24 x 3/4 inch)
Locknut (#10-24)
Capscrew (5/16 x 4 inches)
Washer (5/16 inch)
Flange locknut (5/16 inch)
Wire harness bracket
Cable ties
No parts required
Register at www.Toro.com.
Qty.
–
Prepare the machine.
1
1
2
Assemble the taillights.
4
4
4
4
Assemble the taillights to the machine.
4
2
Install the wire harness brackets.
4
Route and connect the wire harness.
Connect the wire harness to the tow
–
vehicle.
4.
Lower the jack and disconnect the machine from
the tow vehicle; refer to the Operator's Manual
for the machine.
5.
Chock the tires of the machine.
Original Instructions (EN)
All Rights Reserved *3429-633* A
Printed in the USA
Form No. 3429-633 Rev A
Installation Instructions
Use
Advertisement
Related Manuals for Toro 31950
Summary of Contents for Toro 31950
- Page 1 Form No. 3429-633 Rev A Homologation Kit Groundsmaster ® 1200 Series Pull Behind Rotary Mower Model No. 31950 Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine.
- Page 2 Repeat steps for the other reflector and taillight support. Assembling the Taillights to the Assembling the Tail Lights Taillight Support Remove the 4 nuts from the 2 tail light assemblies. Parts needed for this procedure: Left taillight support Right taillight support Reflector triangle Screw (#10-24 x 3/4 inch) Locknut (#10-24)
- Page 3 g280310 g280317 Figure 3 1. Taillight harness 3. Push-in fastener (harness) 2. Taillight-support tube Assembling the Taillights g280311 Figure 4 to the Machine 1. Left taillight assembly 5. Flange locknut (5/16 inch) 2. Right taillight assembly 6. Capscrew (5/16 x 4 inches) Parts needed for this procedure: 3.
- Page 4 g280318 Figure 5 1. Left taillight assembly 3. Left, upper gusset plate (axle-frame tube) 2. Push-in fastener (harness) Installing the Wire Harness g280308 Figure 6 Brackets 1. Flange locknut (1/2 inch) 4. Capscrew (1/2 x 4-1/2 inches) 2. Clevis 5. Harness bracket Parts needed for this procedure: 3.
- Page 5 Installing the Rear Wire Harness Bracket Remove the 2 flange locknuts (1/2 inch), 2 capscrews (1/2 x 4-1/2 inches), and 2 washers (1/2 inch) that secure the hitch tube to the receiver (Figure g280309 Figure 8 g280312 Figure 7 1. Capscrew (1/2 x 4-1/2 4.
- Page 6 Routing and Connecting the Wire Harness Parts needed for this procedure: Cable ties Routing and Connecting the Harness at the Axle-Frame Tube Route the 7-contact connector of the wire harness along the right frame tube as shown in Figure g280316 Figure 10 1.
- Page 7 Routing the Harness at the Frame Route the wire harness along the right frame tube as shown in Figure g280319 Figure 13 1. Hydraulic tubes 4. Right frame tube 2. Push-in fastener (harness) 5. Cable ties 3. Magnetic fastener g280323 (harness) Figure 11 1.
- Page 8 4 sockets and 3 pins; refer to your authorized mower without tensioning the harness. Toro distributor for parts. Bundle the remaining harness and secure it to Assemble the mower to the tow vehicle; refer to...