Advertisement
Table of Contents
- 1 Table of Contents
- 2 Be Sure to Obey this Manual for Safety
- 3 A few Precautions
- 4 Cautions
- 5 Installation Site
- 6 Name and Function of Parts 6~7
- 7 Operating Instructions 8~13
- 8 Care and Maintenance 14~15
- 9 Trouble Shooting
- 10 Attention
- 11 Environmental Conditions
- 12 Specifications
- Download this manual
Advertisement
Table of Contents
Related Manuals for Sanyo MIR-153
Summary of Contents for Sanyo MIR-153
- Page 1 Downloaded from https://www.rsmanuals.com INSTRUCTION MANUAL MIR-153 MIR-253 MIR-553 Cooled Incubator MIR-153 MIR-253 MIR-553...
-
Page 2: Table Of Contents
Downloaded from https://www.rsmanuals.com Be sure to obey this manual for safety. Thank you for your purchase of the Sanyo You must conform to this manual after incubator. Please read these instructions care- read ing throughout well, because this fully before using. - Page 3 Downloaded from https://www.rsmanuals.com Keep these rules for safety by all means. !\WARNING! Don't use it outdoors. When is used at When the repair, maintenance and in- the place splashing the rainwater, this spection is done, change the power sup- may cause electrical leak/shock. ply switch to stop and disconnect the power supply plug.
- Page 4 Downloaded from https://www.rsmanuals.com Place the unit on a level and strong Don't get onto and put a thing on the product. Turning over, damage and fall- place and perform the prevention of turn- ing may cause injury. ing over. When installation is incomplete, this may cause injury by liquid leak, fall- ing and turning over the product.
-
Page 5: A Few Precautions
Downloaded from https://www.rsmanuals.com A FEW PRECAUTIONS O Do not use two-way sockets etc, because it The maximum heat load capacity acceptable to could cause problems. Also use an exclusive this incubator is shown in Figures 2, 3 and 4 breaker. under the heading "TROUBLE SHOOTING."... -
Page 6: Cautions
Downloaded from https://www.rsmanuals.com CAUTIONS O When it is desired to place an instrument re- O If the temperature control is set for below 5°C, quiring a measuring cable and power cord in the the incubator could frost up. If the cooler is ob- cabinet, the cable and cord can be led through structed by the accumulation of frost, its cool- the access hole provided on the left side wall of... -
Page 7: Name And Function Of Parts 6~7
O Observation window ©Drain hole- A 3-ply heat ray absorbing glass -©Lock panel which arrests incoming heat rays (MIR-153 and 253 only) " ©Door switch The cabinet interior can ©Evaporation tray ©Adjustable legs screened from light if the glass protection plate is substituted for one of black. - Page 8 © Glass protection plate (MIR-153 and 253 only) A black plate may be substituted when it is desired that the interi- or of the cabinet be screened from light.
-
Page 9: Operating Instructions 8~13
Downloaded from https://www.rsmanuals.com OPERATING INSTRUCTIONS Name and Function of Each Operation Key and Lamp on the Control Panel • Prevention of Extremities of Temperature The operation keys on the front panel allow Being Reached (LIMIT) the following functions. O Alarm setting key (SET) (1) Setting of temperature. - Page 10 The terminal for the remote alarm is located in the Program step lamp box at the rear top of the frame. (MIR-153, MIR- When this lamp is lit, each step of the programmed 253) operation is conducted.
- Page 11 Downloaded from https://www.rsmanuals.com OPERATING INSTRUCTIONS In this section, temperature settings for the incubator, excessively high/low temperature prevention settings, program settings, program change and start/stop for programmed operation will be explained. The incubator's alarm function will also be described. Before Using Control Panel Table 2 Digital display section Key operation...
- Page 12 Downloaded from https://www.rsmanuals.com [Sample case] OExcessively low temperature ©Program operating prevention knob (LOW) When the interior temperature start/stop key OExcessively high temperature prevention knob (HIGH) of the cabinet is maintained at © Defrost display lamp 10°C for one hour (Step 1), it must be maintained at 25°C ©...
- Page 13 Downloaded from https://www.rsmanuals.com OPERATING INSTRUCTIONS Table 6 Alteration of Program (For step 1, alter the procedure f r o m *4 onward.) in Steps Display sample Key operation Step display Unit display after operation To conduct program step 1 only, follow the procedure Enter the recurrent Light off _ n n...
- Page 14 When cabinet interior Compressor OFF low temperature temperature falls below prevention circuitry excessively low temper- ature prevention setting Temperature fuse 70°C (MIR-153, 253) Blowout heaterOFF 76°C (MIR-553) Blowout heaterOFF Power failure or Operation continues Memory backup (about 5 hours) accidental disconnection...
-
Page 15: Care And Maintenance 14~15
Replacing the f luorescent lamp Remove lamp cover and rubber cap. The floures- cent lamp wül also be detached. [MIR-153, MIR-253] Insert a new bulb into the lamp cover and adjust Remove the 2 screws which hold the shade, work- ing from underneath. - Page 16 Q Cleaning the cabinet interior O Setting the shelves The shelves can be adjusted to the height of [MIR-153, MIR-253] items placed inside. To adjust the height, insert • Turn off the power switch. the self-support clips (4 per shelf) into the slots •...
-
Page 17: Trouble Shooting
If the unit does not function even after these changes have been made, contact your nearest Sanyo Service Center. Details of the following items should accompany any enquires: (1) Conditionoftrouble... -
Page 18: Attention
Use of other rating may cause fire or electric shock. CIRCUIT BREAKER MIR-153 MIR-253 CIRCUIT BREAKER MIR-553 ENVIRONMENTAL CONDITIONS This equipment is designed to be safe at least under... -
Page 19: Specifications
Downloaded from https://www.rsmanuals.com SPECIFICATIONS MIR-153 MIR-253 MIR-553 Model 700(W) x 580(D) x 1018(H)mm 700(W) x 580(D) x 1618(H)mm 800(W) x 832(D) x 1810(H)mm Exterior dimensions 620(W) x 386(D) x 555(H)mm 620(W) x 386(D) x 1075(H)mm 640(W) x 550(D) x 1160(H)mm... - Page 20 Downloaded from https://www.rsmanuals.com SANYO Electric Co., Ltd. Refrigeration Products Division 7FB6P101192003 1 -1 - 1 , Sakata Oizumi-Machi, Ora-Gun, Gunma 370-0596 Japan Recycled paper Printed in Japan...