hit counter script
Siemens SIMATIC PG 760 Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Motherboard
  5. SIMATIC PG 760
  6. Manual
Siemens SIMATIC PG 760 Manual

Siemens SIMATIC PG 760 Manual

Hide thumbs Also See for SIMATIC PG 760:
Table of Contents

Advertisement

Quick Links

Download this manual
SIMATIC
PG 760
Programming Device
Manual
C79000-G7076-C761-01
Preface, Contents
Product Overview
Unpacking and Setting Up the
PG 760
Installing and Operating the
PG 760
PG 760 Expansions
Configuring the PG 760
Error Diagnostics
Hardware Information
Glossary, Index
1
2
3
4
5
6
7

Advertisement

Table of Contents
loading

Related Manuals for Siemens SIMATIC PG 760

Summary of Contents for Siemens SIMATIC PG 760

  • Page 1 Preface, Contents Product Overview Unpacking and Setting Up the PG 760 SIMATIC Installing and Operating the PG 760 PG 760 PG 760 Expansions Programming Device Configuring the PG 760 Manual Error Diagnostics Hardware Information Glossary, Index C79000-G7076-C761-01...

  • Page 2: C79000-G7076-C761

    Trademarks SIMATIC and SINEC are registered trademarks of SIEMENS AG. Third parties using for their own purposes any other names in this document which refer to trademarks might infringe upon the rights of the trademark owners. Copyright...
  • Page 3 Preface What this Manual This manual contains all the information you need for working with the is About PG 760 programming device. You can use it to: unpack the programming device and power it up. familiarize yourself with the functions and settings of the various components (display, keyboard, programming facilities etc.).
  • Page 4 Queries If you have any questions concerning subjects not covered in the manual, simply get in touch with the Siemens representative in your area. The addresses for the maintenance and repair centers and the SIMATIC hotline can be found in the Product Information Bulletin.

  • Page 5: Table Of Contents

    Contents Product Overview ............Unpacking and Setting Up the PG 760 .
  • Page 6 Contents PCI Configuration ..........5-21 Error Diagnostics .

  • Page 7: Product Overview

    Product Overview Application The PG 760 programming device is a high performance device designed specifically for an automation environment. Its performance and equipment make it a unit particularly suitable for programming/configuring with SIMATIC S5 and SIMATIC S7 programmable controllers in the office. Hardware and You can use the PG 760 programming device to program SIMATIC S5 and Software...
  • Page 8 Product Overview Advantages of the Compared with a standard PC, the PG 760 programming device of the PG 760 SIMATIC family has numerous advantages: You can develop, debug and document user programs for SIMATIC S5 and SIMATIC S7 programmable logic controllers with the PG 760 without the need for additional hardware or software.

  • Page 9: Unpacking And Setting Up The

    Unpacking and Setting Up the PG 760 What Does this This chapter describes how to install your PG 760. It provides you with Chapter Contain? comprehensive information on the major components of the PG 760, such as: drives, keyboard, and programming facilities.

  • Page 10: Setup And Hardware Components Of The

    Unpacking and Setting Up the PG 760 Setup and Hardware Components of the PG 760 Unpacking Your Unpack your PG 760 as follows: PG 760 1. Remove the packing. 2. Do not throw the original packing away. Keep it in case you have to ship or transport the unit again at some time in the future.

  • Page 11: Components Of The

    Unpacking and Setting Up the PG 760 Components of the PG 760 Front Side All the important operator controls are accessible from the front of the PG 760. Appliance socket Output Appliance plug Input Mains voltage selector PS/2 keyboard PS/2 mouse LPT 1 MPI/DP COM1...
  • Page 12 Unpacking and Setting Up the PG 760 Ports and Summary of the ports and connectors on the rear panel of the housing: Connectors Ports and Connectors Function Appliance plug, inlet Connection for power supply Appliance socket, outlet Connection for power supply to monitor PS/2 keyboard Connection for keyboard PS/2 mouse...

  • Page 13: Keyboard

    Unpacking and Setting Up the PG 760 Keyboard Keyboard Layout The keyboard is divided into the following areas: Function keys Alphanumeric keyboard Cursor control keys Numeric keypad PG 760 Print Pause Scroll Help SysRq Break Scroll @ ” ^ & &...
  • Page 14 Unpacking and Setting Up the PG 760 Keyboard Labeling The keyboard has an international/German labeling system. International German Shift Together with the ß Unshift ALT Gr key Figure 2-4 The Keyboard Labeling System Special Keys The special keys in the alphanumeric keyboard have the following functions: Function Backspace Key This key moves the cursor one space to the left and deletes the...
  • Page 15 Unpacking and Setting Up the PG 760 Function CTRL Key (combination key) Ctrl This key is only used in combination with other keys. For example, you press CTRL + ALT + Del to reset and restart the operating system. For other uses of this key, please refer to the user manual of the relevant application program.
  • Page 16 Unpacking and Setting Up the PG 760 Cursor Keys The keypad shown below is used for cursor control. Mover cursor to start of file Home Insert Insert Page Page back Delete Page Delete Page forward Move cursor to end of file Move cursor up Move cursor right Move cursor left...
  • Page 17 Unpacking and Setting Up the PG 760 Function Keys There is a row with twelve function keys located above the alphanumeric keyboard. The assignment of the individual function keys depends on the software you are working with. Within the STEP 5 programming software the following keys have specific functions (refer to STEP 5 manual).

  • Page 18: Drives

    Unpacking and Setting Up the PG 760 Key Combinations Various key combinations are shown in the table below. Table 2-1 Key Combinations Key Combination Function Warm restart CTRL Change to international character set CTRL Change to German character set; the German keyboard driver must have already been loaded LED Displays...
  • Page 19 Unpacking and Setting Up the PG 760 Drive Types The PG 760 is equipped with the following drives as standard: Table 2-2 Standard Drives Type of Drive Format Capacity Floppy (diskette) drive 3.5 inch 1.44 Mbytes Hard disk drive 3.5 inch See Product Information Bulletin CD-ROM drive...
  • Page 20 Unpacking and Setting Up the PG 760 Hard Disk Drive You can use a number of different hard disk drives in your PG 760. The memory capacity of the hard disk can be found in the Product Information Bulletin and SETUP program.

  • Page 21: Transport

    Unpacking and Setting Up the PG 760 Transport Carrying the Despite the robust design of the PG 760, its internal components are sensitive PG 760 to severe vibrations or jolts. When moving the PG 760, you must therefore make sure that it is protected from severe mechanical forces. Use the original packing material if you have to ship the PG 760 from one location to another.

  • Page 22: Installing And Operating The

    Installing and Operating the PG 760 What Does This This chapter describes what you have to do to set up your PG 760 correctly Chapter Contain? for operation. This includes: the basic steps for starting up your PG 760, working with memory cards for the programmable controllers, and connecting your PG 760 to other devices.

  • Page 23: Connecting The Pg 760 To The Power Supply

    Installing and Operating the PG 760 Connecting the PG 760 to the Power Supply Connecting to the The PG 760 can be operated at 120 V or 230 V. Voltage selection is carried Power Supply out via the mains voltage selector. Caution Risk of damage to the unit! Operating the PG 760 with the incorrect mains voltage can damage the unit.
  • Page 24 Installing and Operating the PG 760 Connecting the Proceed as follows: Power Cable 1. Check that the correct voltage has been selected. 2. Plug the supplied power cable into the power supply connector. 3. Connect the unit to a socket outlet with a grounded protective conductor. 4.

  • Page 25: Connecting Peripheral Devices

    Installing and Operating the PG 760 Connecting I/O Devices Connecting a PS/2 Connect the keyboard as follows: Keyboard 1. Switch off your PG 760. 2. Plug in the PS/2 keyboard connector. Using a Mouse You can connect both a PS/2 and a serial mouse to the PG 760. When the PG 760 is supplied, the mouse driver for the PS/2 mouse is already loaded.
  • Page 26 You can connect external multisynchronous monitors using the standard Monitors VGA connector on the rear panel of the unit. We recommend that you use Siemens monitors. Connecting You must switch off the PG 760 before connecting the monitor cable. You Monitors will find further information about the connector pinout in Chapter 7.
  • Page 27 Installing and Operating the PG 760 Caution Danger of damaging the monitor! If you want to set higher frequencies and resolutions, first make sure that the monitor you are using is suitable for a higher frequency and resolution. If the frequency is too high, this may damage the monitor. Additional You can plug an additional graphics card into one of the ISA or PCI slots on Graphics Card...
  • Page 28 Installing and Operating the PG 760 Recommended Siemens printers with a parallel interface and IBM character set are Printers recommended for use with the PG 760 programming device. Connecting the To connect your printer, proceed as follows: Printer to the 1.

  • Page 29: Working With Simatic Memory Cards

    Installing and Operating the PG 760 Working with SIMATIC Memory Cards Working with SIMATIC memory cards can be read, programmed and erased using the SIMATIC Memory 68-pin connector. Cards Orientation point SIMATIC Memory Cards Figure 3-5 SIMATIC Memory Card Port Proceed as follows when working with SIMATIC memory cards: 1.

  • Page 30: Connections (Point-To-Point Connections)

    Installing and Operating the PG 760 PG 760 Connections (Point-to-Point Connections) Point-to-Point In this section, you will learn how to connect your PG 760 to a programming Connection device or programmable controller using a point-to-point connection. You can establish a point-to-point connection by connecting the PG 760 to another programming device or a programmable controller via: a V.24 connection.
  • Page 31 Installing and Operating the PG 760 Connecting the If you want to connect your PG 760 to another programming device, you can PG 760 to Other plug the appropriate connecting cable into the V.24 or TTY interface port. Programming You will find more detailed information on the connecting cables listed Devices below in Chapter 7.
  • Page 32 Installing and Operating the PG 760 Connecting the You can connect the PG 760 to a SIMATIC S5 programmable controller via PG 760 to S5 the COM1/TTY interface port. The cable for establishing the connection to Programmable the SIMATIC S5 CPUs is included with the PG 760. Controllers (Order No.
  • Page 33 Installing and Operating the PG 760 Connecting the The connecting cable 6ES5 734-2BD20 is supplied with the PG 760. An PG 740 via an adapter is available for connecting the programmable controller using older Adapter standard cables. Interface Link Connecting Cable Adapter 6ES5 734-2BD20 PG 760 to...

  • Page 34: Multipoint Interface (Mpi/Dp)

    Installing and Operating the PG 760 Multipoint Interface (MPI/DP) Connecting an S7 You can connect your PG 760 to a SIMATIC S7 programmable logic Programmable controller using the floating MPI/DP interface. The MPI cable (5 m long) for Controller via the connection to SIMATIC S7 CPUs is supplied with the PG 760.
  • Page 35 Installing and Operating the PG 760 MPI/PROFIBUS DP Up to 32 devices (PC, programming device or programmable controller) can Network be connected to the MPI/DP interface to form a network segment. The physical coupling to the MPI/PROFIBUS DP network is via a floating RS485 interface which is a component of the programming device basic module.

  • Page 36: Sinec L2

    Installing and Operating the PG 760 SINEC L2 Networking SINEC L2 is an open and robustly designed bus-type local area network PG 740s via (LAN) for industrial applications. It can be used to configure networks with SINEC L2 up to 127 stations. SINEC L2 has a data transfer rate of 1.5 million bps. (PROFIBUS) Principle of SINEC L2 operates on the master-slave principle with token passing...

  • Page 37: Sinec H1

    Installing and Operating the PG 760 SINEC H1 Networking SINEC H1 is an industry-standard bus-type local area network (LAN) based PG 760s via on ETHERNET (ISO 8802/3), and has the following characteristic features: SINEC H1 high speed (10 Mbps), simple expansion capability, open communications (ETHERNET) and widespread applications.

  • Page 38: Pg 760 Expansions

    PG 760 Expansions What Does this You can enhance the performance of your PG 760 by adding additional Chapter Contain? modules. This chapter describes how to expand your PG 760. Please observe the relevant safety guidelines. Summary of In Section You Will Find On Page Sections...

  • Page 39: Opening The Unit

    Risk of damage to the unit! Please note that only qualified personnel should be allowed to work on the open unit, so that the warranty on the device is not affected. Authorized Siemens maintenance and repair centers offer you a specialist maintenance service. The addresses are listed at the end of the Product Information Bulletin.
  • Page 40 PG 760 Expansions Before Opening Please observe the following rules before opening the unit: the Unit Before you disconnect the power supply cable, discharge any electrostatic charge on your body. You can do this by touching the metal mounting plate for the interfaces on the rear panel of the unit. Discharge any electrostatic charge from tools that you are using.

  • Page 41: Components Visible After Opening The Unit

    PG 760 Expansions Components Visible After Opening the Unit View Once you have removed the top cover of your unit, the components are visible. Floppy disk drive / Bus board with expansion slots Memory Hard disk drive support card holder Power supply Back-up battery Motherboard...
  • Page 42 PG 760 Expansions Motherboard The motherboard is the heart of the PG 760. Here, data are processed and stored, and interfaces and device I/Os are controlled and managed. X402 X800 1 2 3 4 5 6 1 2 3 4 5 6 Batt.
  • Page 43 PG 760 Expansions Components on The following components are located on the motherboard of the PG 760: the Motherboard Designat Name Functions Slotbus ISA/PCI connector between basic module and bus module IDE secondary Secondary IDE interface, standard ribbon cable IDE primary Primary IDE interface, standard ribbon cable Keyboard connection MINI DIN keyboard plug Mouse connection...
  • Page 44 PG 760 Expansions Switching the When the PG 760 leaves the factory, the COM1 (TTY) serial port is switched PG 760 to to active (20 mA current loop). If you are connecting two programming Active/Passive devices via the COM1 (TTY) serial port, you must switch one of the ports to passive.
  • Page 45 PG 760 Expansions Switch Settings S1 Manufacturer-specific settings The following switch settings are only listed for information purposes. They are set in the factory and must not be changed. x means that this switch is irrelevant to the described function. S1 (3) S1 (2) S1 (1)
  • Page 46 PG 760 Expansions Standard Settings Figure 4-5 Standard Settings of Switches S1 (1..6) and S2 (1..6) for 133 MHz Pentium Jumper X34 open: S2 (2) S2 (1) Function active TTY-interface (standard setting) TTY-transmit loop isolated from current source (passive setting) TTY-receive loop isolated from current source (passive setting) PG 760 Programming Device...

  • Page 47: Installing Expansion Modules

    PG 760 Expansions Installing Expansion Modules Installing You can extend the functionality of your PG 760 by installing additional Expansion modules. Six expansion slots for long ISA modules are provided on the Modules mother board for this purpose. The current drawn per ISA module must not exceed 9 A at +5 V.

  • Page 48: Installing Memory Expansion Cards

    PG 760 Expansions Installing Memory Expansion Cards Standard Memory There are four slots for 32-bit SIMM memory expansion modules on the motherboard. The current memory configuration is 16 MB. You can extend it to 32, 64, 80 and 128 MB. The memory comes supplied with EDO RAM modules.
  • Page 49 PG 760 Expansions X402 X800 1 2 3 4 5 6 1 2 3 4 5 6 Batt. X701 Figure 4-6 Location of the Memory Slots Caution Risk of damage! The electronic components on the printed circuit boards are highly sensitive to electrostatic discharge.
  • Page 50 PG 760 Expansions Installing the SIMM Plug the SIMM memory cards in as follows: Cards 1. Turn off the unit and unplug the power cable. 2. Open the unit as described in Section 4.1. 3. Remove all inserted ISA, PCI modules. 4.

  • Page 51: Installing A Cache

    PG 760 Expansions Installing a Cache Installing a Cache The motherboard has a slot for an external second-level cache. You can use this cache to enhance your processor power. X402 X800 1 2 3 4 5 6 1 2 3 4 5 6 Batt.

  • Page 52: Installing And Removing Disk Drives

    PG 760 Expansions Installing and Removing Disk Drives Installing and The floppy disk drive is installed on the front of the unit. If necessary, you Removing Floppy can replace it with another. Disk Drives Locking screws Floppy disk drive Figure 4-8 Location of the Floppy Disk Drive Installation of To install or remove the disk drive, proceed as follows:...
  • Page 53 PG 760 Expansions Removal and The CD-ROM drive is fitted in a disk drive block on the front of the unit. A Installation of Disk vacant slot is present in the block for an additional drive. Drive Block (Front) Disk drive block Locking screws Figure 4-9 Disk Drive Block with Free Slot...
  • Page 54 PG 760 Expansions Installing Hard You can install a further 3.5 inch IDE hard disk drive in the disk drive block Disk Drives at the at the back of your PG 760. Provisions for the necessary wiring have already Back of the Unit been made.
  • Page 55 PG 760 Expansions Installation of the To install an additional hard drive in the back of the unit, proceed as follows: Hard Drive (Back) 1. Turn off the unit, unplug the power cable and open the unit as described in Section 4.1. 2.

  • Page 56: Changing The Backup Battery

    Do not recharge the battery and do not open the battery by force. The correct lithium battery can only be ordered from Siemens (Order No.: W79084-E1003-B1). Return used lithium batteries to the manufacturer/recycler or dispose of them as special waste according to local regulations.

  • Page 57: Closing The Unit

    PG 760 Expansions Closing the Unit Closing the Unit To close the unit, proceed as follows: 1. Put the cover on the back of the unit and slide it forwards. 2. Lift the cover slightly and attach it to the front panel (upper edge with guides).

  • Page 58: Configuring The

    Configuring the PG 760 What Does this In this chapter, you will learn how to configure the BIOS of your PG 760 Chapter Contain? programming device. This will be necessary if you have made any changes to your system by adding, removing or replacing an adapter card, a memory expansion card or a system module.

  • Page 59: Changing The System Configuration With Setup

    Configuring the PG 760 Changing the System Configuration with SETUP Changing the The configuration of your programming device is set for working with the Configuration software supplied with the unit. You should only change the preset values if you have modified your PG 760 in any way, or if a fault occurs when the unit is powered up.
  • Page 60 Following below appears following power-on: Power-on PhoenixBIOS Version 4.05 Copyright 1985-1995 Phoenix Technologies Ltd., All Rights Reserved. SIEMENS PG 760 Pentium CPU = Pentium 133 MHz 0000640K System RAM Passed 0015360K Extended RAM Passed System BIOS shadowed Video BIOS shadowed UMB upper limit segment address: F2xx Press F2>...
  • Page 61 Configuring the PG 760 Menu Structure The screen is divided into four parts. In the top part, you can select the menu forms [Main], [Advanced], [Security], [Power], [Exit]. In the left of the center part you can select various settings or submenus. Brief help texts appear on the right for the currently selected menu entry.
  • Page 62 Configuring the PG 760 5.1.1 The Main Menu PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Main Advanced Security Power Exit Item Specific Help System Time: [ 15:55:32 ] [ 11/17/1995 ] System Date: Shift-Tab , or Enter Diskette A: [ 1.44 MB, 31/2” ] selects field.
  • Page 63 Configuring the PG 760 System Time and System Time and System Date indicate the current values. Once you have System Date selected the appropriate option, you can use the [+] and [–] keys to modify Time and Date the time setting Hour:Minute:Second and the date Month/Day/Year .
  • Page 64 Configuring the PG 760 IDE Adapter A branch is made to the following submenu when you select this type of Hard Disk Drive menu option: PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Main Advanced Security Power Exit IDE Adapter 0 Master (C: 1624 Mb) Item Specific Help Autotype Fixed Disk [Press Enter]...
  • Page 65 Configuring the PG 760 Option “ Multi-Sector The number of sectors which are transmitted per interrupt are transferred in Transfers” the option “Multi-Sector Transfers”. The value depends on the drive and should only be set using the autodetect function. Disabled 1 sector 2,4,6,8,16 sectoren...
  • Page 66 Configuring the PG 760 Option “Memory The following submenu appears when you select the option “Memory cache” Cache” in the main menu: PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Main Advanced Security Power Exit Memory Cache Item Specific Help Cache: [Enabled] Cache Controls.
  • Page 67 Configuring the PG 760 Option “Memory The following submenu appears when you select the option “Memory Shadow” shadow” in the main menu: PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Main Advanced Security Power Exit Memory Shadow Item Specific Help System shadow: Enabled Video BIOS may be copied to shadow RAM for increased...
  • Page 68 Configuring the PG 760 Option “Boot The following submenu appears when you select the option “Boot Sequence” Sequence” in the main menu: PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Main Advanced Security Power Exit Boot Options Item Specific Help Boot sequence: [A: then C:] Order system searches drives for a boot disk.
  • Page 69 Configuring the PG 760 Example of a summary screen: PhoenixBIOS 1985-95 Phoenix Technologies Ltd. Pentium CPU [133MHz]: F276 – FFFF System ROM: Coprozessor: Installed BIOS Date: 04/01/96 System RAM: 640 Kb COM Ports: 03F8, 02F8 Extended RAM: 15360 Kb LPT Ports: 0378 Shadow RAM: 384 Kb...
  • Page 70 Configuring the PG 760 Option “Hardware The following submenu appears when you select the option “Hardware Options” Options” in the main menu: PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Advanced Security Power Exit Main PG 760 Hardware Options Item Specific Help [Adr.

  • Page 71: The Advanced Menu

    Configuring the PG 760 5.1.2 The Advanced Menu Menu Structure PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Main Advanced Security Power Exit Item Specific Help Warning! Setting items on this menu to incorrect va- lues may cause your system to malfunction. PCI Devices Plug &...
  • Page 72 Configuring the PG 760 Option “PCI The following Submenu appears when you select the option “PCI Devices” Devices” in the advanced menu: PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Main Advanced Security Power Exit PCI Devices Item Specific Help PCI Device, Slot #1: Enable selected device Enable Master: [Enabled]...

  • Page 73: The Security Menu

    Configuring the PG 760 5.1.3 The Security Menu Summary You can only edit the options enclosed in square brackets. Two passwords are assigned to protect your programming device from unauthorized use. You can use the supervisor password to prevent use of diskettes for the normal user and to limit use of the hard disk.

  • Page 74: The Power Menu

    Configuring the PG 760 5.1.4 The Power Menu Summary This menu has the following structure: PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Main Advanced Security Power Exit Item Specific Help APM: Enabled Power Savings: Disabled APM (Advanced Power Management) allows APM aware software to better Standby Timeout: Disabled manage power savings.
  • Page 75 Configuring the PG 760 In suspend mode, the CPU is stopped and can only be restarted by an interrupt, for example, keyboard, mouse, COM 1/2, hard disk. Standby CPU CPU speed in standby mode: Speed [Low] 1/16 CPU clock [Medium] 1/8 CPU clock [High] 1/4 CPU clock...

  • Page 76: The Exit Menu

    Configuring the PG 760 5.1.5 The Exit Menu Summary The setup program is always terminated using this menu. PhoenixBIOS Setup-Copyright 1985-95 Phoenix Technologies Ltd. Main Advanced Security Power Exit Item Specific Help Save Changes & Exit Exit Without Saving Changes Exit after writing all changed SETUP Get Default Values item values to CMOS.
  • Page 77 Configuring the PG 760 Documenting your If you have made any modifications to your standard SETUP settings, you System can enter them in the following table. You then have ready access to the Configuration values you have set if you have to make any hardware modifications later. System Parameter Standard Settings Your Entries...

  • Page 78: Pci Configuration

    Configuring the PG 760 PCI Configuration The system is configured automatically when you switch it on. The following table lists the default settings. Bus No. Device Function Description Intel 82437Fx(TSC) Intel 82371FB(PIIX) PCI/ISA jumper Intel 82371FB(PIIX) IDE-PCI interface 00h-07h GD7543 Cirrus LCD-SVGA PCI slot 1 PCI slot 2 PG 760 Programming Device...

  • Page 79: Error Diagnostics

    Error Diagnostics What Does this Chapter 6 will support you in handling simple errors and faults that you Chapter Contain? yourself can diagnose and, in some cases, eliminate. The chapter describes all the possible errors and faults, explains their causes and makes suggestions as to how to eliminate them.
  • Page 80 Error Diagnostics Table 6-1 Errors/Faults in PG 760 Operation Error Cause Remedy Power-ON LED does not light up PG 760 is switched off Switch the PG 760 on Power supply not properly Check power supply connected connections, power cable and power plug Message: Incorrect configuration data...

  • Page 81: Hardware Information

    Hardware Information What Does This This chapter contains important reference data about the following: Chapter Contain? Hardware addresses Interrupt assignments Information about connecting cables. Summary of In Section You Will Find On Page Sections Hardware Address Table Interrupt Assignments Connector Pinouts Connecting Cables 7-15 PG 760 Programming Device...

  • Page 82: Hardware Address Table

    Hardware Information Hardware Address Table There are two kinds of address areas: Memory address area I/O address area. Different read/write signals (I/O WR, I/O RD, MEMR, MEMW) are used to reference these areas. The following tables provide you with an overview of the address areas used.
  • Page 83 Hardware Information Memory decoding The Pentium CPU has a memory address area of 4 Gbyte. The CPU has a function 64-bit wide data bus, 29 address lines (A3...A31) and 8 bus enable lines (BD0...BE7) which code the non-existent byte address lines A0, A1 and A2. The CPU address bus is mapped on the PCI address bus via the TSC (system controller).
  • Page 84 Hardware Information Table 7-2 I/O address assignment Address Size Function From Byte Basic Function Possible Alternative Function 0000 000F PiiX DMA 1 0020 0021 PiiX PIC 1 (interrupt controller) 002E 002F Configuration port Ultra I/O 0040 0043 PiiX Timer1 (SW clock/refresh/speaker) 0060 0060 Keyboard controller date...
  • Page 85 Hardware Information From Byte Basic Function Possible Alternative Function Address Size Function 03E0 03E1 Vacant 03E8 03EF COM 3 not used 03F0 03F5 Floppy 1 on board 03F6 03F6 Primary IDE command 03F7 03F7 Primary IDE status / Floppy Change 03F8 03FF COM 1 / TTY...
  • Page 86 Hardware Information I/O and Memory Below are listed the I/O and memory assignments of a number of expansion Assignments modules set in the factory. Please consult the relevant hardware descriptions, since you can also select other settings. Table 7-4 I/O and Memory Assignments I/O Address Memory Address Module...

  • Page 87: Interrupt Assignments

    Hardware Information Interrupt Assignments Interrupt The PG 760 uses two integral interrupt controllers of the type 82C59 to Assignments handle the 16 hardware interrupts (IRQ 0 to IRQ 15). The INT output of the slave controller is connected to the IRQ 2 input of the master controller.

  • Page 88: Connector Pinouts

    Hardware Information Connector Pinouts PS/2 Mouse The connector has the following pinout: Socket Connector View of socket connetor Figure 7-1 Connector Pinout for a PS/2 Mouse Designation Input/Output Data line Input/output Unassigned 5 V power supply (short-circuit proof) Output Clock line Input/output Unassigned Connecting a...
  • Page 89 Hardware Information VGA Socket The VGA socket connector on the PG 760 has the following pinout: Connector Figure 7-3 VGA Socket Connector Pin No. Designation Description Input/Output R_EXT Output G_EXT Green Output B_EXT Blue Output Ground Ground Ground Ground Ground EXT_H Horizontal sync.
  • Page 90 Hardware Information MPI/DP Socket The MPI/DP socket connector on the PG 760 has the following pinout. The Connector interface is electrically isolated. Figure 7-4 MPI/DP Socket Connector Pin No. Designation Description Input/ Output Pin 1 is not assigned. Pin 2 is not assigned. LTG_B Signal line B of MPI module.
  • Page 91 Hardware Information Parallel Port The parallel port (LPT1) on the PG 760 has the following pinout: Figure 7-5 Parallel Port LPT1 (Socket Connector) Pin No. Signal Designation Input/Output / Strobe (CLK Output (open collector) Data - Bit 0 Output (TTL level) Data - Bit 1 Output (TTL level) Data - Bit 2...
  • Page 92 Hardware Information Serial Port The serial port (COM1) on the PG 760 has the following pinout: (PLC/V.24/Modem) Figure 7-6 Serial Port COM1 (Socket Connector) Pin No. Designation Description Input/Output TxD (D1) Serial transmit data Output RxD (D2) Serial receive data Input RTS (S2) Request to send...
  • Page 93 Hardware Information Serial Port The serial port (COM2) on the PG 760 has the following pinout: (V.24/Mouse) Figure 7-7 Serial Port COM2 (Plug Connector) Designation Description Input/Output DCD (M5) Data carrier detect Input RxD (D2) Receive data Input TxD (D1) Transmit data Output DTR (S1)
  • Page 94 Hardware Information Settings on the Two different pairs of the address/bus lines of the local PCI bus can be Bus Module selected as select signals for the two PCI slots using the pin connectors J300, J302. Pin connector: J300 Setting: Jumper 1-2: IDSEL PCI-slot 1 = AD 28 (standard setting) Jumper 2-3:...
  • Page 95 Hardware Information Connecting Cables Overview 15 pin PG-SS COM1/TTY 25 pin PG-SS COM1/TTY see Figures 7-9, 7-10 and 7-11 COM1/TTY COM1/... see Figure 7-12 COM1/TTY PG-SS/TTY COM1/TTY PG-SS/TTY see Figures 7-9 and 7-10 COM1/TTY AG-SS/TTY see Figure 7-13 COM1/V.24 COM1/V.24 see Figure 7-14 ET200 connector/RS 485 MPI/RS 485...

  • Page 96: Connecting Cables

    Hardware Information PG7xx - PLC You can use the standard connecting cable (supplied along with your PG 760) Standard to connect your PG 760 to a Siemens programmable controller. Please read Connection the notes in Chapter 3. Connecting cable PG 7xx...
  • Page 97 Hardware Information PG 7xx - PLC With the 25-pin plug connecting cable, you can connect your programming Connection via device via an adapter to a PLC, for example PLC 150U (AS 511). PG 6xx Connecting Cable with 25-Pin Socket S5, V.24 PG 7xx Adapter Connecting cable...

  • Page 98: Technical Information

    Hardware Information PG 7xx - PG 6xx If you want to connect your PG 760 to the PLC-S5 port of a PG 6xx Connection to programming device, you will need an adapter. In this case, the PG 760 must PLC-S5 Port be switched to active.

  • Page 99: Glossary

    This chapter contains a glossary in which you will find a list of the Chapter Contain? terminology used in conjunction with the Siemens range of programming devices and a brief explanation of each of the terms. PG 760 Programming Device...
  • Page 100 Glossary Access Protection Access to the programs and data of a programming device can be protected by passwords. Application An application is a program which builds directly on, for example, the operating system. Applications on your programming device are MS-DOS/Windows, the STEP 5 Basic package, GRAPH 5, etc. ASCII Editor With an ASCII editor you can process (that is, edit) text files which are stored in ASCII code (American Standard Code of Information Interchange).
  • Page 101 Glossary COM2 port The COM2 port is a serial V.24 interface which can be used to connect a mouse or a printer. Configuration These are files which define the configuration after booting. Examples of Files such files are CONFIG.SYS and AUTOEXEC.BAT. Configuration The configuration software brings the device configuration up to date when Software...
  • Page 102 Glossary Drop-Down Menu In graphics-supported programs, a menu line is positioned at the top edge of the screen. The menu titles contained in this line can be set either as drop-down or pull-down menus. Drop-down menus “roll” down as soon as the mouse pointer passes over a menu title.
  • Page 103 Glossary Interface (Port) An interface is the connection between individual hardware elements such as PLCs, programming devices, printers or monitors via physical connections (cables). An interface is also the connection between different programs, to enable them to work together. Interface Module Module which controls and extends the hardware periphery.
  • Page 104 Glossary Modem Communications device that enables a computer to send and receive data over a telephone line. Modulator and demodulator of a signal transmission facility. It converts the digital pulses from a computer into analog signals (and vice versa). Module Modules are boards (printed circuit boards) which can be plugged into a programmable controller or programming device.
  • Page 105 Glossary Operating system Collective term for all programs which, in conjunction with the hardware, control and monitor execution of the user programs, the distribution of resources among the individual user programs and the maintenance of the operating mode (for example, MS-DOS). Parallel Interface Information is transmitted one byte at a time via a parallel interface (port).
  • Page 106 Glossary RAM (Random Access Memory) is a read/write memory in which every memory location can be addressed individually and its contents changed. RAM is used to store data and programs. ROM (Read Only Memory) is a memory in which every memory location can be addressed individually.
  • Page 107 Glossary Software The collective term for all programs which are used on a computer. The operating system and the user programs are part of the concept “software”. STEP 5 This is a software package which is the basis for all other STEP 5 software Basic Package packages.
  • Page 108 Glossary Warm Restart A warm restart is a restart after a program has been aborted. The operating system is reloaded and restarted. A warm restart is performed with the key combination CTRL+ALT+DEL. Working Memory The memory in which a program is stored which can be processed. The working memory is a direct access memory.

  • Page 109: Index

    Index Active/passive switching, 4-7 Graphics card, 3-6 Address areas, 7-2 Hard disk drive, 2-12 Back-up battery, 4-19 Hardware information, 7-1 BIOS, 5-2 I/O address area, 7-2 Cache, 4-14 Installation, 3-1 Clock, 4-19 Interrupt, 7-7 Closing the unit, 4-20 ISA modules, 4-10 COM 1, 7-12 COM 2, 7-13 Connecting cables, 7-15...
  • Page 110 Index SIMATIC S7 programmable controller, 3-13 SINEC H1, 3-16 Overview/connecting cables, 7-15 SINEC L2, 3-15 Special keys, 2-6 Switch position, 4-7 System configuration, 5-2 Parallel port, 7-11 Power supply, 3-2 Printer, 3-7 Product overview, 1-1 Transport, 2-13 Programming device, advantages of the programming device, 1-2 Unpacking, 2-2 Serial port, 7-12, 7-13...
  • Page 111 Siemens AG AUT E 146 Östliche Rheinbrückenstr. 50 D–76181 Karlsruhe Federal Republic of Germany From: Your Name: _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _...
  • Page 112 Your comments and recommendations will help us to improve the quality and usefulness of our publications. Please take the first available opportunity to fill out this questionnaire and return it to Siemens. Please give each of the following questions your own personal mark within the range from 1 (very good) to 5 (poor).

Table of Contents