Table of Contents
Advertisement
Quick Links
Quick Start Guide for the
Limitless™ Series WDRR Receiver
WARNING
PERSONAL INJURY
• DO NOT USE these products as safety or emergency
stop devices or in any other application where failure of
the product could result in personal injury.
Failure to comply with these instructions could result in
death or serious injury.
WARNING
Honeywell does not recommend using devices for critical
control applications where there is, or may be, a single point
of failure or where single points of failure may result in an
unsafe condition. It is up to the end-user to weigh the risks
and benefits to determine if the products are appropriate for
the application based on security, safety and performance.
Additionally, it is up to the end-user to ensure that the
control strategy results in a safe operating condition if any
crucial segment of the control solution fails.
Honeywell customers assume full responsibility for learning
and meeting the required Declaration of Conformity,
Regulations, Guidelines, etc. for each country in their
distribution market.
Failure to comply with these instructions could result in
death or serious injury.
Sensing and Control
WARNING
RF EXPOSURE
• To satisfy FCC RF exposure requirements for mobile
transmitting devices, a separation distance of 20 cm or
more should be maintained between the antenna of this
device and persons during device operation To ensure
compliance, operation at closer than this distance is not
recommended. The antenna used for this transmission
must not be co-located in conjunction with any other
antenna or transmitter.
Failure to comply with these instructions could result
in death or serious injury.
WARNING
• The WDRR must be installed in accordance with the
requirements specified in this document in order to
comply with the specific Country Communication
Agency requirements. (i.e. FCC, IC, ETSI, ACMA, etc.)
See Section 3 as it requires choosing the correct
Country Use Code and thus allowable antenna and/or
cable usage.
CAUTION
• Power to the WDRR should not be applied during
installation of antenna as damage could occur to the
WDRR electronics.
CAUTION
* The WDRR receiver offers optimal performance when
paired with Limitless™ inputs that have a firmware
version of 7170 or a greater number (i.e., FW7170 will
be printed on the Limitless™ input label). If the
Limitless™ input is paired with older firmware (FW7170
or a lesser number), the WDRR may exhibit delayed
responses under simultaneous operation.
Issue 2
50063986
Advertisement
Table of Contents
Related Manuals for Honeywell Limitless WDRR Series
Summary of Contents for Honeywell Limitless WDRR Series
- Page 1 The antenna used for this transmission WARNING must not be co-located in conjunction with any other Honeywell does not recommend using devices for critical antenna or transmitter. control applications where there is, or may be, a single point Failure to comply with these instructions could result in death or serious injury.
- Page 2 Limitless™ inputs. Figure 1 (see below) contains labels of the features and descriptions of the WDRR DIN-Rail Receiver where the function, operation, etc. of each will be provided throughout this document. Figure 1 – Limitless™ WDRR Din-Rail Receiver with location call-outs Honeywell Sensing and Control...
-
Page 3: Risk Of Electrical Shock
ATTENTION Only Honeywell antennas types should be used. The antenna gain when using the WDRR should meet the Country Communication Agency requirements for the specific country the WDRR is being used in. - Page 4 CAUTION Do not apply direct power (supply voltage “+” or “-”) to the “-” terminal or “+” terminal or any of the NPN/PNP type output terminals as damage could occur to the WDRR electronics. Honeywell Sensing and Control...
- Page 5 CAUTION Do not apply direct power (supply voltage “+” or “-”) to the “-” terminal or “+” terminal or any of the NPN/PNP type output terminals as damage could occur to the WDRR electronics. Honeywell Sensing and Control...
-
Page 6: Configuration Dip Switches
Refer to Figure 1. One green LED turns on to indicate power is applied to the WDRR receiver. This occurs when the electrical power is supplied to the “+” and “-” power supply terminals. Honeywell Sensing and Control... - Page 7 RF Link switch position 0-9, A-E Lost RF Signal LED status Condition Solid green Acceptable RF link(s) Solid red Lost RF link(s) RF Link switch position F Sequence each LED color LED test mode Honeywell Sensing and Control...
-
Page 8: Function Button
The battery will need to be activated in the Limitless™ switch and proper power applied to the WDRR Series Receiver before proceeding with this pairing procedure. Once the pairing is completed, the Limitless™ switch selected will only communicate with the WDRR Receiver it was paired to and no other device. Honeywell Sensing and Control... -
Page 9: Step Action
Record the Limitless™ switch Sequence # on identification labels and apply to the Limitless™ switch housing in desired locations (See Figure 6). Repeat Steps 2-7 to add additional Limitless™ switch. Up to 14 Limitless™ switches can be paired to a single WDRR. Honeywell Sensing and Control... - Page 10 Figure 5. Limitless™ Switch with Function Button Depressed Figure 4. Limitless™ Switch Housing NOTE: Use a blunt object, such as a paper clip or tooth pick to actuate the function switch Figure 6. Limitless™ Switch Label Placement Honeywell Sensing and Control...
- Page 11 Also, ensure that the housing is being mounted on a flat surface. Figure 8. Limitless™ WDRR Mounting Tabs Honeywell Sensing and Control 11...
-
Page 12: Antenna Adjustment
The antenna used for this transmitter must not be co-located in conjunction with any other antenna or transmitter. Failure to comply with these instructions could result in death or serious injury. Honeywell Sensing and Control... -
Page 13: Sales And Service
Latin America +1-305-805-8188 +1-305-883-8257 Fax While we provide application assistance personally, through our literature and the Honeywell web site, it is up to USA/Canada +1-800-537-6945 the customer to determine the suitability of the product in +1-815-235-6847 the application.