hit counter script
IBM 5887 Removal And Replacement Procedures
  1. Manuals
  2. Brands
  3. IBM Manuals
  4. Enclosure
  5. 5887
  6. Removal and replacement procedures

IBM 5887 Removal And Replacement Procedures

Power systems
Hide thumbs Also See for 5887:
Table of Contents

Advertisement

Quick Links

See also: Installation
Power Systems
5887 removal and replacement
procedures
IBM

Advertisement

Table of Contents
loading

Related Manuals for IBM 5887

Summary of Contents for IBM 5887

  • Page 1 Power Systems 5887 removal and replacement procedures...
  • Page 3 Power Systems 5887 removal and replacement procedures...
  • Page 4 Note Before using this information and the product it supports, read the information in “Safety notices” on page v, “Notices” on page 11, the IBM Systems Safety Notices manual, G229-9054, and the IBM Environmental Notices and User Guide, Z125–5823. ™...

  • Page 5: Table Of Contents

    Notices ........11 Trademarks . . 12 Electronic emission notices . . 12 Class A Notices . . 12 Class B Notices . . 16 Terms and conditions . . 19 © Copyright IBM Corp. 2011, 2017...

  • Page 7: Safety Notices

    You should also refer to the safety information documentation any time you do not clearly understand any safety information in the U.S. English publications. Replacement or additional copies of safety information documentation can be obtained by calling the IBM Hotline at 1-800-300-8751.
  • Page 8 Electrical voltage and current from power, telephone, and communication cables are hazardous. To avoid a shock hazard: v Connect power to this unit only with the IBM provided power cord. Do not use the IBM provided power cord for any other product.
  • Page 9 Observe the following precautions when working on or around your IT rack system: v Heavy equipment–personal injury or equipment damage might result if mishandled. v Always lower the leveling pads on the rack cabinet. v Always install stabilizer brackets on the rack cabinet. v To avoid hazardous conditions due to uneven mechanical loading, always install the heaviest devices in the bottom of the rack cabinet.
  • Page 10 CAUTION: Removing components from the upper positions in the rack cabinet improves rack stability during relocation. Follow these general guidelines whenever you relocate a populated rack cabinet within a room or building: v Reduce the weight of the rack cabinet by removing equipment starting at the top of the rack cabinet.
  • Page 11 (L003) All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for class 1 laser products. Outside the U.S., they are certified to be in compliance with IEC 60825 as a class 1 laser product.
  • Page 12 Exchange only with the IBM-approved part. Recycle or discard the battery as instructed by local regulations. In the United States, IBM has a process for the collection of this battery. For information, call 1-800-426-4333. Have the IBM part number for the battery unit available when you call. (C003)

  • Page 13: Removal And Replacement Procedures

    4. Ensure that you have access to a Phillips screwdriver. 5. If parts are incorrect, missing, or visibly damaged, contact your service provider or next level of support. © Copyright IBM Corp. 2011, 2017...
  • Page 14 Electrical voltage and current from power, telephone, and communication cables are hazardous. To avoid a shock hazard: v Connect power to this unit only with the IBM provided power cord. Do not use the IBM provided power cord for any other product.

  • Page 15: Removing And Installing A Disk Drive

    Removing and installing a disk drive You can service a disk drive concurrently. Attention: Failure to follow the steps sequentially for this field replaceable unit (FRU) removal or installation might result in damage to the FRU or system. Use the following precautions whenever you handle electronic components or cables: v Attach a wrist strap to an unpainted metal surface of your hardware to prevent electrostatic discharge (ESD) from damaging your hardware.

  • Page 16: Removing And Installing An Enclosure Services Manager

    2. Slide the disk drive into the disk drive enclosure until the drive stops. 3. Rotate the handle to the locked position. Figure 2. Installing a disk drive in the disk drive enclosure Removing and installing an enclosure services manager You can remove and install an enclosure services manager (ESM) concurrently only when its amber fault light is on solid.

  • Page 17: Removing And Installing A Midplane

    2. If any of these conditions are not true, continue the repair only after powering off the unit containing the FRU that is being repaired, and begin with The ESM will be serviced nonconcurrently. Otherwise, continue with The ESM will be serviced concurrently. v The ESM will be serviced concurrently.
  • Page 18 v Attach a wrist strap to an unpainted metal surface of your hardware to prevent electrostatic discharge (ESD) from damaging your hardware. v If you do not have a wrist strap, before removing the product from ESD packaging and installing or replacing hardware, touch an unpainted metal surface of the system for a minimum of 5 seconds.
  • Page 19 Figure 4. Removing the midplane assembly screws 8. Remove the midplane assembly. a. Rotate the midplane assembly up about 45 degrees. b. Lift the midplane assembly out of the enclosure. Figure 5. Removing the midplane assembly 9. Remove the midplane. a.
  • Page 20 Figure 6. Removing and installing the midplane 10. Install the midplane. a. Align the six screw holes on the midplane with the six screw holes on the midplane assembly. b. Secure the midplane to the midplane assembly with the six screws that you removed earlier in this procedure.

  • Page 21: Removing And Installing A Power Supply

    17. Install the disk drives making sure that each disk drive is inserted back into the same slot from which it was removed. For instructions, see “Removing and installing a disk drive” on page 3. 18. Restore power to the power supplies of the disk drive enclosure and power on the system or partition.
  • Page 22 v The power supply will be serviced nonconcurrently. Power off the system or partition that is using the disk drive enclosure. Remove the power-cable retention brackets. Label and remove the power cables from the power supplies of the disk drive enclosure.

  • Page 23: Notices

    All statements regarding the manufacturer's future direction or intent are subject to change or withdrawal without notice, and represent goals and objectives only. The manufacturer's prices shown are the manufacturer's suggested retail prices, are current and are subject to change without notice. Dealer prices may vary. © Copyright IBM Corp. 2011, 2017...

  • Page 24: Trademarks

    IBM, the IBM logo, and ibm.com are trademarks or registered trademarks of International Business Machines Corp., registered in many jurisdictions worldwide. Other product and service names might be trademarks of IBM or other companies. A current list of IBM trademarks is available on the Web at Copyright and trademark information at www.ibm.com/legal/copytrade.shtml.
  • Page 25 Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.
  • Page 26 The following is a summary of the EMI Taiwan statement above. Warning: This is a Class A product. In a domestic environment this product may cause radio interference in which case the user will be required to take adequate measures. IBM Taiwan Contact Information:...
  • Page 27 Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben. Des Weiteren dürfen auch nur von der IBM empfohlene Kabel angeschlossen werden. IBM übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung von IBM verändert bzw.

  • Page 28: Class B Notices

    Consult an IBM-authorized dealer or service representative for help. Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. Proper cables and connectors are available from IBM-authorized dealers. IBM is not responsible for...
  • Page 29 This product is in conformity with the protection requirements of EU Council Directive 2004/108/EC on the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards.
  • Page 30 Um dieses sicherzustellen, sind die Geräte wie in den Handbüchern beschrieben zu installieren und zu betreiben. Des Weiteren dürfen auch nur von der IBM empfohlene Kabel angeschlossen werden. IBM übernimmt keine Verantwortung für die Einhaltung der Schutzanforderungen, wenn das Produkt ohne Zustimmung von IBM verändert bzw.

  • Page 31: Terms And Conditions

    Permissions for the use of these publications are granted subject to the following terms and conditions. Applicability: These terms and conditions are in addition to any terms of use for the IBM website. Personal Use: You may reproduce these publications for your personal, noncommercial use provided that all proprietary notices are preserved.
  • Page 34 IBM® Printed in USA...

This manual is also suitable for:

Power system power7 series

Table of Contents