PAHCMS000 AHU Communications Kit features are: • It can be used with LG Multi V air or water source outdoor units and LG Single Zone outdoor units. • It supports AHU coil capacities from 12 - 594 kBtu/h.
Page 30
Main Module Address Setting An address for the main module is needed when PAHCMS000 is connected to an LG central controller The address of main module can be set within ‘1~247’. In this case, the address of the main module should be the same as the address in LG central controller.
EEV Control Note : When a communication module(or PAHCMR000) is connected to the main module of PAHCMS000, DO and UI in communication module are not used. Due to our policy of continuous product innovation, some specifications may change without notification.
Remote controller connected to PAHCMR000 can only monitor status. 2. LG Central controller addressing for discharge air temp. controller should be set to the same address as the main module’s address. 3. Address of Comm. module of PAHCMS000 (Central control address) must be set to ‘00’. The address for additional PAHCMR000 must be set with an order increasing by 1.
Page 38
Remote controller connected to PAHCMR000 can only monitor status. 2. LG Central controller addressing for discharge air temp. controller should be set to the same address as the main module’s address. 3. Address of Comm. module of PAHCMS000 (Central control address) must be set to ‘00’. The address for additional PAHCMR000 must be set with an order increasing by 1.
Page 39
Remote controller connected to PAHCMR000 can only monitor status. 2. LG Central controller addressing for discharge air temp. controller should be set to the same address as the main module’s address. 3. Address of Comm. module of PAHCMS000 (Central control address) must be set to ‘00’. The address for additional PAHCMR000 must be set with an order increasing by 1.
Page 40
Remote controller connected to PAHCMR000 can only monitor status. 2. LG Central controller addressing for discharge air temp. controller should be set to the same address as the main module’s address. 3. Address of Comm. module of PAHCMS000 (Central control address) must be set to ‘00’. The address for additional PAHCMR000 must be set with an order increasing by 1.
Page 41
Remote controller connected to PAHCMR000 can only monitor status. 2. LG Central controller addressing for discharge air temp. controller should be set to the same address as the main module’s address. 3. Address of Comm. module of PAHCMS000 (Central control address) must be set to ‘00’. The address for additional PAHCMR000 must be set with an order increasing by 1.
Page 42
1. Remote controllershouldbeconnected toPAHCMS000. Remote controller connected to PAHCMR000 can only monitor status. 2. LG Central controller addressing for discharge air temp. controller should be set to the same address as the main module’s address. 3. Address of Comm. module of PAHCMS000 (Central control address) must be set to ‘00’. The address for additional PAHCMR000 must be set with an order increasing by 1.
Introduction Figure 16: EEV Kit. When used with the LG AHU Communications Kit (sold separately), the LG EEV Kit controls refrigerant flow between LG Multi V air-source or water-source units and a third-party air handler unit (AHU). The EEV Kits for PAHCMS000 are offered in four sizes: •...
Page 59
Contact your LG representative if you have any questions about the AHU Communications Kit or its installation.
Page 60
LG Customer Information Center, Commercial Products 1-888-865-3026 USA LG Electronics, U.S.A., Inc. Follow the prompts for commercial A/C products. Commercial Air Conditioning Division 4300 North Point Parkway Alpharetta, Georgia 30022 www.lg-vrf.com IM_AHU_Comm_Kit_PAHCMS000_8_18...