Safety Precautions General Guide Lines When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or damaged by the short circuit. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly installed.
Prevention of Electrostatic Discharge (ESD) to Electrostatically Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor "chip"...
About lead free solder (PbF) Note: Lead is listed as (Pb) in the periodic table of elements. In the information below, Pb will refer to Lead solder, and PbF will refer to Lead Free Solder. The Lead Free Solder used in our manufacturing process and discussed below is (Sn+Ag+Cu). That is Tin (Sn), Silver (Ag) and Copper (Cu) although other types are available.
Service Hints How to remove the back cover Lay the main unit face down. (see Fig.5) Fig.5 Remove the 5 fixing screws and the pedestal assembly. (see Fig.6) SCREWS Fig.6 Remove the 22 fixing screws and the back cover. (see Fig.7) SCREWS SCREWS Fig.7...
Self-check is used to automatically check the bus lines and hexadecimal code of the TV set. To enter Self-Check mode, keep pressing the down (-/v) button on the TV set and press the STATUS button on the remote control. To exit Self Check, switch off the TV set at the power button. TX-LR37V10 37FHD Panasonic 2009LCD Self Check Complete 7B03 O.K.
Power LED blinking timing chart Subject Information of LED Flashing timing chart. Contents When abnormality has occurred the unit, the protection circuit operates and reset to the stand by mode. At this time, the defective block can be identified by number of blinking of the Power LED on the front panel of the unit. Blinking Blinking timing Contents...
Service Mode Function MPU controls the functions switching for each IICs through IIC bus in this chassis. The following setting and adjustment can be adjusted by remote control in Service Menu How to enter SERVICE While pressing (-/v) button on the TV unit, press on the remote control for 3 times within 2 seconds.
SERVICE SERVICE Peaks SOFT 2.212 OPTION 1 Key Command ADJUST Peaks EEP 01.02.0003 OPTION 2 S e r v i c e 1 WB-ADJ Peaks BOOT 1.00 OPTION 3 OPTION LSI DATA 1.00.09 Model ID • STBY SOFT 1.00.00 03233100 SRV-TOOL Press the 3/4 button to change the adjustment values or function.
Option Bytes Description OPTION1 ATP Search speed Slow (1) / Fast (0) TEXT Ch Refresh ON (1) / OFF (0) ID-1 ON (1) / OFF (0) Macrovision Auto-judge ON (1) / OFF (0) Surround enable low bit ON (1) / OFF (0) Surround enable high bit ON (1) / OFF (0) Pre Emphasis...
Adjustment Method Sub-Contrast/White Balance Adjustment Instrument Name Connect to Remarks Remote controller Correlation can be also taken by LCD WB meter (Minolta CA-210 or equivalent) CS-1000A or equivalent Comunication jig Computer for external control Procedure Remarks Let the panel standfor more than 3 hours at more than 20 °C.
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List.
Page 22
Parts Location NOTE: The numbers on the exploded view below refer to the exploded view section of the Replacement Parts List. Difference for 37’’...
Replacement Parts List Important Safety Notice Components Identified by mark have special characteristics important for safety. * When replacing any of these components, use only manufacturers specified parts. In case of ordering these spare parts, please always add the complete Model-Type number to your order. RTL (Retention Time Limited) Note: The marking (RTL) indicates that the Retention Time is Limited for this item.
Page 24
Cct Ref Parts Number Description Cct Ref Parts Number Description IC8504 C3EBCG000100 LAN EEPROM D4568 EZAEG2A50AX ESD SUPPRESSOR IC8580A C3ZBN0000035 FLASH MEMORY D4569 EZAEG2A50AX ESD SUPPRESSOR IC8581 C3FBTC000033 FLASH MEMORY D4573 EZAEG2A50AX ESD SUPPRESSOR IC8621 C0DBZYY00266 REGULATOR D4574 EZAEG2A50AX ESD SUPPRESSOR RM2500 B3RAD0000168 LED RECEIVER...
Schematic Diagrams IMPORTANT SAFETY NOTICE Components identified by mark have special characteristics important for safety. When replacing any of these components, use only manufacturers' specified parts. NOTE RESISTOR All resistors are carbon ¼W resistor, unless marked otherwise. Unit of resistance is OHM (Ω) (k=1,000, M=1,000,000) CAPACITORS All capacitors are ceramic 50V unless marked otherwise.