Page 2
IMPORTANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by the users, and have therefore not been restated.
EMX62M SPECIFICATIONS G General specifications 135 W/8Ω @0.5% THD at 1 kHz (SPEAKERS OUT) Maximum output power 200 W/4Ω @0.5% THD at 1 kHz (SPEAKERS OUT) 175 mW/40Ω @0.5% THD at 1 kHz (PHONES OUT) 20 Hz–20 kHz +1 dB, –3 dB @1 W output into 8Ω (SPEAKERS OUT) Frequency response 20 Hz–20 kHz +1 dB, –3 dB @+4 dB output into 10 kΩ...
Page 4
EMX62M G Input specificaitons Input level Actual load Nominal Connector Input connectors PAD impedance impedance type Sensitivity Nominal level Max. before cliping 50–600Ω Mics –62 dB (0.616 mV) –50 dB (2.45 mV) –20 dB (77.5 mV) CH INPUT (Lo-Z) XLR-3-31 3 kΩ...
EMX62M PANEL LAYOUT G CONTROL PANEL 1. CONTROL SECTION • Channel Control Equalizer (HIGH, LOW) ➁ MONITOR control ➂ EFFECT control √ LEVEL control ➄ PAD switch (CH1-4) ➁ ➂ ➃ ➄ • Digital Effect ≈ EFFECT select switch ∆...
Page 8
AUX IN control 2TR IN control MASTER control Peak Level Indicator LIMITER indicator • MONITOR EFFECT RTN control MASTER control • PHANTOM switch, indicator PHANTOM ON/OFF switch • YAMAHA SPEAKER PROCESSING ON/OFF switch • POWER switch, indicator POWER ON/OFF switch, indicator...
Page 9
EMX62M 2. INPUT/OUTPUT SECTION INPUT terminal (Hi-Z, Low-Z) (CH1-4) INPUT terminal (LINE 1, 2) (CH5) INPUT terminal (Super Hi-Z) (CH6) EFFECT OUT terminal FOOT SW terminal INPUT TO MAIN terminal (AUX IN) INPUT TO MAIN terminal (2TR IN) OUTPUT terminal (REC OUT)
EMX62M DISASSEMBLY PROCEDURE Front Panel Assembly (Time required: about 3 min) 1-1. Remove the seven (7) screws marked [80] and the screw marked [90]. (Fig.1) 1-2. Hold volume knobs and pull the panel to the front. (Fig.1) 1-3. Remove the screw marked [100]. The front panel assembly can then be removed.
Page 15
EMX62M 2-3. Remove the six (6) screws marked [160] to remove the shield plate. (Fig.3) 2-4. Remove the fifteen (15) screws marked [40], the nine (9) screws marked [41], and the fourteen (14) hexagonal nuts marked [A]. (Fig.4) 2-5. Remove the twelve (12) knobs marked [50], eight (8) knobs marked [60], the eight (8) knobs marked [70], and the eight (8) knobs marked [80].
Page 16
EMX62M MIX62 Circuit Board 2/2 (Time required: about 4 min) 3-1. Remove the front panel assembly. (See Procedure 1) 3-2. Pinch slightly the stopper of the power switch escutcheon with a plyer, and pull it to the front to remove. (Fig.6-1) 3-3.
Page 17
EMX62M PWR Circuit Board 2/3 (Time required: about 7 min) 5-1. Remove the rear panel assembly. (See Procedure 4) 5-2. Remove the screw marked [100] and the two (2) hexagonal nuts marked [C]. The PWR circuit board 2/3 can then be removed. (Fig.7)
Page 18
EMX62M Power Transformer (Time required: about 6 min) 8-1. Remove the rear panel assembly. (See Procedure 4) 8-2. Remove the four (4) screws marked [43]. The power transformer can then be removed. (Fig.11) [43] Power Transformer (Fig. 11) [43]: Bind Head Tapping Screw-B 4.0X8 MFZN2BL (EG340190) Front Frame (Time required: about 6 min) 9-1.
EMX62M LSI PIN DESCRIPTION YSS234 (XN299A00) Digital Sound Processor MIX62: IC507 NAME FUNCTION NAME FUNCTION AVDD DC A+5Vs bus DC D+5V External RAM interface data TST0 DC D+5V TST1 DC D+5V ...
Page 22
EMX62M MIX62 1/2 Circuit Board HIGH HIGH HIGH HIGH HIGH HIGH VOCAL LARGE HA SMALL HA MONITOR MONITOR MONITOR MONITOR MONITOR MONITOR EFFECT EFFECT EFFECT EFFECT EFFECT EFFECT LEVEL LEVEL LEVEL LEVEL LEVEL LEVEL Hi-Z Hi-Z Hi-Z Hi-Z LINE 1...
Page 23
EMX62M PHAMTOM VOCAL ON / OFF LARGE HALL SMALL HALL MASTER EFFECT RTN YAMAHA SPEAKER PROCESSING ON / OFF GRAPHIC EQUALIZER MASTER EFFECT RTN AUX IN 2TR IN POWER to PWR1/3-CN101 PHONES 2TR IN 1 REC OUT 1 EFFECT OUT...
Page 26
EMX62M PWR 1/3 Circuit Board to PWR2/3-W101BL2 to PWR2/3-W101RE2...
Page 27
EMX62M to Power Transformer Component side 3NA-V826840...
Page 28
EMX62M PWR 2/3 Circuit Board SPEAKERS to PWR 1/3-W101BL1 to PWR 1/3-W101RE1 PWR 3/3 Circuit Board to Power Tranceformer to MIX62 2/2-CN001 AC IN MIX62 2/2 Circuit Board ON / OFF to PWR 3/3 Component side Pattern side 1Pin-W102YE 2Pin-Non Connect...
EMX62M Gain Check On condition of 2.1, confirm that the output level of each terminal meets the table 2.2-1. Table 2.2-1 [unit: dBs] INPUT INPUT LEVEL MAIN OUT MONITOR OUT EFFECT OUT REC OUT PHONES OUT Low-Z +4±2 +4±2 +4±2 -13.8±2...
Page 31
EMX62M Distortion Rate Check On condition of 2.1, set the INPUT and MASTER volume for each terminal to nominal position. Then, confirm that the distortion rate is within 0.3% when the output level is +14dBs. (except REC OUT and PHONES OUT) Maximum Output Level Check At MAIN OUT, MONITOR OUT, EFFECT OUT terminals on condition of 2.7, confirm that the output level of +20dBs can be...
Page 32
Apply 70Hz / -26dB signal into input terminal, and confirm that the output level is within 6.5±2dB from the level for 1kHz input with YAMAHA SPEAKERS PROCESSING switch OFF. Besides, confirm that the LED lights up when YAMAHA SPEAKERS PROCESSING switch is ON and that LED goes out when the switch is OFF.
Page 33
EMX62M Stability Check (1) Connect 10pF~0.47µF capacitor in parallel to the 4Ω load resistance and apply rectangule signal of 10kHz/-26dBs. Then, confirm that overshoot and ringing are as follows. < _ _ Overshoot: Vp/Vo Ringing: within 5 waves (2) Connect 10µH~0.47H inductor in series to the 4Ω load resistance and apply rectangule signal of 10kHz/-26dBs.
EMX62M PARTS LIST RACK MOUNT KIT RK-88 CONTENTS OVERALL ASSEMBLY ...................... 2 FRONT PANEL ASSEMBLY ....................4 REAR PANEL ASSEMBLY ....................6 ELECTRICAL PARTS ....................... 8 RK-88 RACK MOUNT KIT ....................20 Note) DESTINATION ABBREVIATIONS Australian model South African model...
Page 45
EMX62M I OVERALL ASSEMBLY B130 B120 B110...
Page 60
EMX62M PART NO. DESCRIPTION REMARKS QTY RANK REF NO. VZ354300 C161 Ceramic Capacitor-E 0.0022 500 M VV067400 CN101 Connector Base Post M2426XX 14P TE LB932060 CN103 Base Post Connector VH- 6P TE LB932030 CN104 Base Post Connector VH- 3P TE...
EMX62M I RK-88 RACK MOUNT KIT PART NO. DESCRIPTION REMARKS QTY RANK REF NO. RACK MOUNT KIT RK-88 VB132700 Bind Head Screw 4.0X12 MFZN2BL Rack Angle (V840830) *: New Parts RANK: Japan only...