hit counter script
ABB KP-4.1 Product Manual
  1. Manuals
  2. Brands
  3. ABB Manuals
  4. Keypad
  5. KP-4.1
  6. Product manual
ABB KP-4.1 Product Manual

ABB KP-4.1 Product Manual

Hide thumbs

Advertisement

Table of Contents

2CQA 100 007 B0001 │ 2018-09-28
Product Manual
ABB-free@home™
KP-4.1 Keypad

Advertisement

Table of Contents
loading

Related Manuals for ABB KP-4.1

Summary of Contents for ABB KP-4.1

  • Page 1 2CQA 100 007 B0001 │ 2018-09-28 Product Manual ABB-free@home™ KP-4.1 Keypad...

  • Page 2: Table Of Contents

    table of contents table of co ntent s The Device ............................3 Function Overview ........................3 Adding the Keypad ..........................4 Configuring the Keypad ........................6 LED Settings ..........................7 Technical Data ............................. 8 Technical Data........................... 8 Resetting the Device..........................9 │2 Product Manual 2CQA 100 007 B0001 │...

  • Page 3: The Device

    The Keypad allows the user to select from up to four different scenes/environments and operate special functions in an ABB-free@home™ Smart Home system. It has 4 exchangeable keys. The device does not directly control a load but instead commands other free@home components to turn ON or OFF based on the configured settings.

  • Page 4: Adding The Keypad

    Adding the Keypad Adding the Keypad This section describes how to add the Keypad to the system. STEP 1: Install the Light Switch Install the device by following the Operating Instructions included in the original packaging. Note: After installation, the Keypad will not function. To configure the Keypad, it will need to be added to the free@home network.
  • Page 5 Adding the Keypad Start Go to Settings > free@home radio > Search for wireless devices The SysAP will now search for the Keypad. Note: The Keypad can only be found if the search starts within 30 minutes after the Keypad was connected to power.

  • Page 6: Configuring The Keypad

    Configuring the Keypad Configuring the Keypad STEP 1: Enter Keypad Settings Click on the Keypad symbol to show its settings. Select which button to configure first. Define a name for this Keypad. STEP 2: Configure Button A) In the settings menu, press “Top push button” (or the name that corresponds to the button currently being configured).

  • Page 7: Led Settings

    Configuring the Keypad C) If desired, add additional devices to be switched from the same button by repeating steps A and B. In the picture below, the user created a custom scene that turns off all lights on the ground floor and added this to the “Top push button”.

  • Page 8: Technical Data

    Technical Data Technical Data Technical Data Designation Value Operating Voltage 120 VAC, 60 Hz Operating-Voltage Range 110 VAC to 125 VAC Connection Neutral Wire Required Maximum Power Consumption < 1 W Standby* Power Consumption < 300 mW Transmission Protocol free@home, 2.400 - 2.483 GHz, meshed Transmission Power <...

  • Page 9: Resetting The Device

    Resetting the Device Resetting the Device Reset the Light Switch if it was previously assigned to a different System Access Point (SysAP). The reset will remove any previous connection and enable the device to connect to a new SysAP. Reset procedure: A) Press and hold the bottom key for at least 20 seconds.
  • Page 10 860 Ridge Lake Boulevard changes to the contents of this Memphis, TN 38120 document without prior notice. abb.com/freeathome The detailed specifications agreed upon apply for orders. ABB accepts no responsibility for possible errors Customer Service: or incompleteness in this 800-816-7809 document.

Table of Contents