Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions
and maintained properly, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Instruction
Wear eye
Manual
Protection
1. SAFETY
DANGER! BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR
THIS REASON, IT IS VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE THE
BATTERY TESTER.
Follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend to use in the
vicinity of the battery. Remember to review warning marks on all products and on engines.
1.1.
Personal Safety
WARNING! Wear approved eye protection. Wear appropriate Personal Protective Equipment. A full range of Personal Protective
‰
Equipment is available from your Sealey stockist.
Remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit
9
current high enough to melt or weld a ring, which would cause severe burns.
Ensure that hands and clothing are clear of fan blades and other moving or hot engine parts. Remove ties and ensure that belts
9
cannot become entangled.
Ensure that there is another person within hearing distance and is able to come to your aid should a problem arise when working
9
near a lead-acid battery.
Have fresh water nearby in case battery acid contacts skin or clothing; flush affected area immediately. If acid enters eyes, flush
9
immediately with clean running water for a minimum of 15 minutes, seek medical attention.
DO NOT smoke or allow a spark or flame in the vicinity of the battery or engine.
8
1.2.
General Safety
Familiarise yourself with the application, limitations and potential hazards of the tester. Also refer to the vehicle manufacturer's hand
9
book. IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.
Ensure that the tester is in good condition before use. If in any doubt do not use the unit and contact a qualified electrician.
9
Only use recommended attachments and parts. To use unapproved items may be dangerous and will invalidate your warranty.
9
Keep tools and other items away from the engine and ensure that you can see the battery and working parts of engine clearly.
9
Determine the system voltage before using the tester.
9
If the tester receives a sharp knock or blow the unit must be checked by a qualified service agent before using.
9
Clean battery terminals before using the tester.
9
Keep children and unauthorised persons away from the work area.
9
DO NOT dismantle the tester for any reason. The tester must only be checked by qualified service personnel.
8
WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area, or allow
‰
them to touch the battery terminals.
DO NOT cross-connect tester to battery. Ensure positive (red) clamp is to positive terminal and negative (black) clamp is to
8
negative terminal. If battery symbols cannot be distinguished, remember that the negative terminal is the one directly connected to
the vehicle bodywork.
DO NOT use the tester outdoors, or in damp, or wet locations and DO NOT use in the vicinity of flammable liquids or gases.
8
Ensure there is effective ventilation to prevent a build-up of explosive gases.
8
DO NOT use the tester for a task for which it is not designed.
8
When not in use, store the tester carefully in a safe, dry, childproof location.
Modern vehicles contain extensive electronic systems. You are required to check with the vehicle Manufacturer, for any specific
9
instructions regarding the use of this type of equipment on each vehicle.
2. INTRODUCTION
Compact device which accurately tests battery, cranking and alternator. No heat, no sparks and no misdiagnosis. Just key in the battery rating
from the top of the battery and results are displayed on an LED control panel. No internal battery and will test batteries with a residual charge of
just 7V.
© Jack Sealey Limited
INSTRUCTIONS FOR:
DIGITAL BATTERY & ALTERNATOR TESTER 12V
BT01
MODEL NO:
Wear
Wear
Protective
Protective
Clothing
Gloves
Original Language Version
Explosive
Corrosive
Material
Substance
BT01
Issue:1 - 12/07/17
Advertisement
Related Manuals for Sealey BT01
Summary of Contents for Sealey BT01
- Page 1 BT01 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions and maintained properly, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Model No: ........
- Page 3 5.3. - If the screen shows blank: A. The voltage of the tested battery is too low to operate the BT01. Recharge the suspect battery and retest. If reading is the same, the battery should be replaced immediately. B. The clamps are cross connected. Connect the clamps correctly.