Related Manuals for Motorola SDC1000
Summary of Contents for Motorola SDC1000
- Page 1 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER OPERATING MANUAL MOTOROLA SDC1000 - 1 -...
-
Page 2: Table Of Contents
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER CONTENTS 1. Important Safety Instructions 2. General 3. Features 4. Specifications 5. Name of the Parts 6. Identifying supplied parts 7. Installation of the Product 8. Wire Color Table of the Main Unit 9. Wire Connection in of basic application 10. -
Page 3: Important Safety Instructions
If the product exhibit a distinct change in performance. 2. General SDC1000 is an intelligent one door Access Controller based on powerful 8 bit Microprocessor to meet a simple and cost-effective access control market requirement. User friendly device allows you to register max. 128 USER IDs and easy to add or delete USER RFIDs. -
Page 4: Specifications
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 4. Specification .CPU : Dual 8 bit Microprocessors .Memory : 8 KB Program memory 512 bytes Flash memory .User PIN numbers : 128 User RFIDs including one Master RFID .Proximity Reader : Built-in 4” Proximity reader .Input/Output... -
Page 5: Installation Of The Product
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 7. Installation of the Product . Drill two 6-32 holes and one 1/2" hole on the proper location of the wall. (If the gang box is already installed on the wall then skip this step.) 7-2. -
Page 6: Wire Color Table Of The Main Unit
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 8. Wire Color Table of the Main Unit POWER Power(DC 12V) +12V Red wire, Red with White stripe Power(DC 12V) 0V(GND) Black wire, Black with White stripe OUTPUT Door RELAY(2A) Gray wire with Red stripe... -
Page 7: Wire Connection In Of Basic Application
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 9. Wire connection for basic application This connection can be changed for different applications. - 7 -... - Page 8 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER . Power Connection Connect (+)wire of DC 12V power to Red wire and Red/White stripe wire and connect Power GND(-)wire of DC 12V to Black wire and Black/White stripe wire. . Door Lock connection 9-2-1 Connection of POWER FAIL SAFE: Door Lock - Connect Door RELAY(COM),Grey/Red stripe wire to DC +12V.
- Page 9 - Connect RS232-GND, Yellow wire of Main Unit to pin number 5 of 9-pin connector. - Plug in 9-pin connector to COM1 or COM2 Port of Personal Computer. - Install and run SDC1000 Time & Attendance Software. 9-9. Chime Bell Unit connection(Extra Purchase, If Necessary) - Connect Red(+) wire of Chime Bell Unit to Bell Output, Brown/White wire of Main Unit.
-
Page 10: Initial Setup
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 10. Initial Setup Main Unit has Flash Memory to retain all setting values and when it delivered to customer there is no data in the memory therefore Initial Setup is required for the first use. - Page 11 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER ¨ ë Now, the Main Unit is entered to normal operation mode with default setting. 10-3. Registration of PIN ONLY MODE ¨ ç Turn switch on DC12V Power Supply. All 3 LEDs will be flashing with starting sound.
-
Page 12: Operation
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 11. Operation 11-1 . Normal Operation Mode(Safe Mode) When the Main Unit is running in normal operation mode, Yellow LED is flashing every second. 11-2 . Open the Door User Access Card(or PIN) is granted, Door opens for 3 seconds with "do-mi-sol-do"... -
Page 13: Setting Changes
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 11-7 . Chime Bell operation When the guest presses (Bell) Button from the keypad, Chime Bell melody is activating for 5 seconds. 12. Setting Changes To change previous setting values, you need Master Card(or PIN) to get in to Setting Change mode. - Page 14 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER Command Change setting values Unconditional Door Open Unconditional Door Close Enable QUICK ACCESS MODE(Operate only PIN MODE) Disable QUICK ACCESS MODE(Operate only PIN MODE) Disable Melody sound Enable Melody sound Change keypad lock time when Try Out error detected Detect AUX#1 Input from 'L' to ‘H'...
- Page 15 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 12-11. Add User Access Cards(RF CARD ONLY MODE) ..Master card Command Cards to be registered ..Master card 12-12. Add User Access Cards(RF CARD + PIN MODE) ..Master card Command Cards to be registered ..
- Page 16 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER <Table 1> Settings for command 21~28 Symbol Setting Values Examples/Remarks (You must add value ¨ ç and ¨ è ) EX1)Act ivate Door Relay Setting value for activating time all the time ¨ ç Activate Time...
- Page 17 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 12-21. Change Door open time when User Access Card(or PIN) is granted (Please refer to Table 1 for Master card or Command Door time TTL time MasterPIN 12-22. Change Alarm time when User Access Card(or PIN) is denied...
- Page 18 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 12-28. Change Alarm time when magnet detected (Please refer to Table 1 for OM, Master card or Command Output Mode Door Time Alarm Time TTL Time MasterPIN 12-29. Register 2 digits Duress Alarm PassWord...
- Page 19 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 12-39. Change Chime Bell activating time (Please refer to Table 1 for Master card or Command Chime Bell Time MasterPIN 12-41. Unconditional Door Open Master card or MasterPIN 12-42. Unconditional Door Close Master card or MasterPIN 12-43.
- Page 20 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 12-61. Detect AUX#1 Input from 'L' to ‘H' AUX#1 input is detected on the raising edge of AUX#1 input Master card or MasterPIN 12-62. Detect AUX#1 Input from 'H' to ‘L' AUX#1 input is detected on the falling edge of AUX#1 input...
- Page 21 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 12-70. Detect Door Contact sensor Input from 'H' to 'L' Door Contact input is detected on the falling edge of Door Contact input Master card or MasterPIN 12-71. Activate TTL output to ‘H' TTL output changes the state from logic '0' to logic '1' when it activates.
- Page 22 MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 12-82. Set number of times of Try-Out NN is the Try-out numbers from 00 to 99 times. Master card or Command Try-out Numbers MasterPIN 12-83. Set input limit time from the keypad (Please refer to Table 1 for...
-
Page 23: Fcc Registration Information
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 13. FCC REGISTRATION INFORMATION FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the responsible for compliance cold void the user's authority to operate the equipment. -
Page 24: Warranty And Service
MOTOROLA SDC1000 SINGLE DOOR ACCESS CONTROLLER 14. Warranty and Service The following warranty and service information applies only to the United States of America and Republic of Korea. For the information in other countries, please contact your local distributor. To obtain in or out of warranty service, please prepay shipment and return the unit to the appropriate facility listed below.