Honeywell UDC1200 MICRO-PRO Product Manual
Universal digital controller
Hide thumbs
Also See for UDC1200 MICRO-PRO:
- Product manual (2 pages) ,
- Startup manual (11 pages) ,
- Startup manual (21 pages)
Advertisement
Quick Links
59311-3
HONEYWELL UDC1200 & UDC1700 MICRO-PRO
UNIVERSAL DIGITAL CONTROLLER PRODUCT MANUAL (51-52-25-123-EN)
CAUTION:
Installation should be only performed by
technically competent personnel. Local Regulations
regarding electrical installation & safety must be observed.
1. INSTALLATION
Models UDC1200 and UDC1700 have different case sizes (refer to section 10).
Installation differences between these models the have been clearly shown.
Note: The functions described in sections 2 thru 9 are common to all models.
Installing Option Modules
UDC1200 Module Positions
CPU PCB
Mounting Struts
Option Module A
Option Module 1
Option Module 3
Option Module 2
PSU PCB
UDC1700 Module Positions
CPU PCB
Mounting Struts
Option Module B
Option Module A
Option Module 2
Option Module 3
Option Module 1
PSU PCB
To access modules 1, A or B, first detach the PSU and CPU boards from the front by
lifting first the upper, and then lower mounting struts. Gently separate the boards.
a.
Plug the required option modules into the correct connectors, as shown below.
b.
Locate the module tongues in the corresponding slot on the opposite board.
c.
Hold the main boards together while relocating back on the mounting struts.
d.
Replace the instrument by aligning the CPU and PSU boards with their guides
in the housing, then slowly push the instrument back into position.
Note: Option modules are automatically detected at power up.
Option Module Connectors
UDC1200 Module Connectors
Option Slot 1
Option Slot A
Connectors
Connectors
PL7 & PL8
PL5 & PL6
Option Slot 2
Option Slot 3
Connector
Connector
PL4A
PL4B
UDC1700 Module Connectors
Option Slot B
Connectors
PL2A, PL2B &
PL2C
Option Slot 2
Connector
PL4A
Option Slot 1
Connectors
PL7 & PL8
Option Slot A
Connectors
PL5 & PL6
Option Slot 3
Connector
PL4B
Panel-Mounting
The mounting panel must be rigid, and may be up to
6.0mm (0.25inch) thick. Cut-out sizes are:
UDC1200
UDC1700
Dim A = 45mm
Dim A = 45mm
Dim B = 45mm
Dim B = 92mm
A
For n multiple instruments mounted side-by-side, cut-out
dimension A is 48n-4mm
Tolerance +0.5, -0.0mm
Slide mounting clamp
over the instrument
Mounting Panel
housing towards rear face
of mounting panel until
Instrument
the tongues engage in
Housing
ratchets and instrument is
clamped in position.
Ratchets
Gasket
Hold instrument firmly in
position (apply pressure
to bezel only)
CAUTION:
Do not remove the panel gasket; it is a seal against dust and
moisture.
Rear Terminal Wiring
USE COPPER CONDUCTORS (EXCEPT FOR T/C INPUT)
Single Strand wire gauge: Max 1.2mm (18SWG)
UDC1200 Wiring Diagram
UDC1700 Wiring Diagram
These diagrams show all possible option combinations. The actual
connections required depends on the exact model and options fitted.
CAUTION:
Check information label on housing for correct operating
voltage before connecting supply to Power Input
Fuse: 100 – 240V ac – 1amp anti-surge
24/48V ac/dc – 315mA anti-surge
Note: At first power-up the message !"#" $"%& is displayed, as described in
section 7 of this manual. Access to other menus is denied until configuration
mode is completed
2. SELECT MODE
Select mode is used to access the configuration and operation menu functions.
B
It can be accessed at any time by holding down
and pressing
In select mode, press
or
to choose the required mode, press
An unlock code is required to prevent unauthorised entry to Configuration, & Setup
modes. Press
or
to enter the unlock code, then press
Mode
Upper
Lower
Description
Display
Display
'(#)*
+,$#*
Operator
Normal operation
Set Up
+-#(*
+,$#*
Tailor settings to the application
$"%&*
+,$#*
Configuration
Configure the instrument for use
Product Info
1%&"*
+,$#*
Check manufacturing information
2#3%*
+,$#*
Auto-Tuning
Invoke Pre-Tune or Self-Tune
Note: The instrument will always return automatically to Operator mode if
there is no key activity for 2 minutes.
3. CONFIGURATION MODE
First select Configuration mode from Select mode (refer to section 2).
Press
to scroll through the parameters, then press
required value. Press
to accept the change, otherwise parameter will revert to
previous value. To exit from Configuration mode, hold down
return to Select mode.
Note: Parameters displayed depends on how instrument has been configured.
Refer to user guide (available from your supplier) for further details.
Parameters marked * are repeated in Setup Mode.
Parameter
Lower
Upper
Adjustment range & Description
Display
Display
Input
1%4#
See following table for possible codes
Range/Type
Code Input Type &
Code
Input Type &
Code Input Type &
Range
Range
B: 100 - 1824 ºC
L: 0.0 - 537.7 ºC
bC
L
.
C
P24F
B: 211 - 3315 ºF
L
F
L: 32.0 - 999.9 ºF
bF
.
C: 0 - 2320 ºC
N: 0 - 1399 ºC
CC
NC
C: 32 - 4208 ºF
N: 32 - 2551 ºF
CF
NF
J: –200 - 1200 ºC
R: 0 - 1759 ºC
JC
rC
JF
J: –328 - 2192 ºF
rF
R: 32 - 3198 ºF
j
C
J: –128.8 - 537.7 ºC
S: 0 - 1762 ºC
.
SC
j
F
J: –199.9 - 999.9 ºF
S: 32 - 3204 ºF
.
SF
K: –240 - 1373 ºC
T: –240 - 400 ºC
KC
tC
./.8/
KF
K: –400 - 2503 ºF
tF
T: –400 - 752 ºF
k
C
K: –128.8 - 537.7 ºC
t
C
T: –128.8 - 400.0 ºC
.
.
K
F
K: –199.9 - 999.9 ºF
t
F
T: –199.9 - 752.0 ºF
.
.
L: 0 - 762 ºC
LC
PtRh20% vs. 40%:
P24C
0 - 1850 ºC
L: 32 - 1403 ºF
LF
Note: Decimal point shown in table indicates temperature resolution of 0.1°
Parameter
Lower
Upper
Adjustment range & Description
Display
Display
Scale Range Lower Limit +100
Scale Range
)3,
Upper Limit
to Range Maximum
Range Minimum to
Scale Range
),,*
Lower Limit
Scale Range Upper Limit -100
Decimal point
0=XXXX, 1=XXX.X, 2=XX.XX, 3=X.XXX
94"+
position
(non-temperature ranges only)
+%!,
Primary only
Control Type
$:;4
Primary & Secondary
932,
(e.g. heat & cool)
)-3*
Primary Output
Reverse Acting
$:<,
Control Action
91)*
Direct Acting
46=1
Process High Alarm
46,"
Process Low Alarm
2,2.
Alarm 1Type
9>*
Deviation Alarm
?2%9
Band Alarm
%"%>
No alarm
High Alarm 1
4@2.
value*
Range Minimum to Range Maximum in
display units
Low Alarm 1
4,2.
value*
Band Alarm 1
?2,.
1 LSD to span from setpoint in display units
value*
Dev. Alarm 1
92,.
+/- Span from setpoint in display units
value*
Alarm 1
2=;.
1 LSD to full span in display units
Hysteresis*
Alarm 2 Type*
2,20
High Alarm 2
4@20
value*
Options as for alarm 1
Low Alarm 2
4,20
value*
Band Alarm 2
?2,0
value*
Parameter
Lower
Upper
Display
Display
Dev. Alarm 2
92,0*
.
Value*
to enter.
Alarm 2
2=;0*
Hysteresis*
to proceed.
,2>%*
91+2 (disabled) or >%2? (enabled)
Loop Alarm
Default
Loop Alarm
,2:1*
Unlock
Time*
Codes
%"%-
None
2,2.
Alarm Inhibit
C%@1*
./*
2,20
0/*
?"#@
None
4)1
/*
+-D*
2E69
2.6)
2069
206)
,469
F+>.*
Output 1 Usage
or
to set the
,46)
')69
and press
, to
')6)
2969
296)
)-#+
)-#4
Default
/68*
/6./
5$*
Linear Output 1
#;4.*
06./
Range
/60/
Range
760/
PtRh20% vs 40%:
Retransmit
32 - 3362 ºF
)".=*
Output 1 Scale
maximum
Pt100: -199 - 800 ºC
PTC
Retransmit
Pt100: -328 - 1472 ºF
PtF
)".,*
Output 1 Scale
Pt100: -128.8 - 537.7 ºC
minimum
Pt
.
C
Output 2 Usage
F+>0*
Pt
F
Pt100: -199.9 - 999.9 ºF
.
Linear Output 2
#;40*
/60/
0 - 20 mA DC
Range
760/
4 - 20 mA DC
Retransmit
)"0=*
Output 2 Scale
/68/
0 - 50 mV DC
maximum
10 - 50 mV DC
Retransmit
)"0,*
/68
Output 2 Scale
0 - 5 V DC
minimum
.68
1 - 5 V DC
F+>G*
Output 3 Usage
/6./
0 - 10 V DC
Linear Output 3
#;4G*
06./
2 - 10 V DC
Range
Retransmit
)"G=*
Output 3 Scale
Default
maximum
Retransmit
Range max
)"G,*
Output 3 Scale
(Lin=1000)
minimum
Range min
91A(*
., 0, G, 7, 8 or H
Display Strategy
(Linear=0)
2+$C
1
Serial
?%
Mm
4)"#*
Communications
?>
Mm
Protocol
+%!,*
?"
Mm
..0*
)-3*
Serial
0.7*
Communications
?239*
7.I*
Bit Rate
B.H*
.B.0*
46=1*
299)* *.*
Comms Address
)6
Ww
$">%*
Comms Write
)6/*
Range Max
91+.
Digital Input 1
91!1*
Usage
912A
Range Min
91+.
Digital Input 2
8*
91!0*
912A
Usage
91)A
8*
Note: 91!0 has priority over 91!1 if both are configured for the same usage.
.*
If 91!1 or 91!0 = 91+. the remote setpoint input is disabled.
46,"*
Range Max
Range Min
8*
Adjustment range & Description
Default
8
Options as for alarm 1
.
91A2
BB.8B
1 sec to 99 mins. 59secs
No alarms Inhibited
Alarm 1 inhibited
%"%-
Alarm 2 inhibited
Alarm 1 and alarm 2 inhibited
Primary Power
Secondary Power
Alarm 1, Direct
Alarm 1, Reverse
Alarm 2, Direct
Alarm 2, Reverse
Loop Alarm, Direct
4)1
Loop Alarm, Reverse
Logical Alarm 1 OR 2, Direct
Logical Alarm 1 OR 2, Reverse
Logical Alarm 1 AND 2, Direct
Logical Alarm 1 AND 2, Reverse
Retransmit SP Output
Retransmit PV Output
0 to 5 V DC output 1
0 to 10 V DC output
/6./
2 to 10 V DC output
0 to 20 mA DC output
4 to 20 mA DC output
-1999 to 9999
(display value at which output
Range max
will be maximum)
-1999 to 9999
(display value at which output
Range min
will be minimum)
As for output 1
Sec or Al2
/6./
As for output 1
-1999 to 9999
(display value at which output
Range max
will be maximum)
-1999 to 9999
(display value at which output
Range min
will be minimum)
2E69
As for output 1
/6./
As for output 1
-1999 to 9999
(display value at which output
Range max
will be maximum)
-1999 to 9999
(display value at which output
Range min
will be minimum)
.
(refer to section 8)
ASCII
Modbus with no parity
?%
Mm
Modbus with Even Parity
Modbus with Odd Parity
1.2 kbps
2.4 kbps
7.I
4.8 kbps
9.6 kbps
19.2 kbps
.
1 to 255 (Modbus), 1 to 99 (ASCII)
Read/Write
)6
Ww
Read only
Setpoint 1 / Setpoint 2 select*
91+.
Automatic / Manual select
Setpoint 1 / Setpoint 2 select*
Automatic / Manual select
91)+
Remote / Local setpoint select
Continued on next page...
Advertisement
Related Manuals for Honeywell UDC1200 MICRO-PRO
Summary of Contents for Honeywell UDC1200 MICRO-PRO
- Page 1 Lower Upper Adjustment range & Description Default 2. SELECT MODE HONEYWELL UDC1200 & UDC1700 MICRO-PRO The mounting panel must be rigid, and may be up to Display Display UNIVERSAL DIGITAL CONTROLLER PRODUCT MANUAL (51-52-25-123-EN) 6.0mm (0.25inch) thick. Cut-out sizes are: Select mode is used to access the configuration and operation menu functions.
- Page 2 Parameter Lower Upper Adjustment range & Description Default 10. SPECIFICATIONS 5. AUTOMATIC TUNING MODE 8. OPERATOR MODE Display Display UNIVERSAL INPUT /60/* 0 to 20 mA DC input* First select Automatic tuning mode from Select mode (refer to section 2). This mode is entered at power on, or accessed from Select mode (see section 2).