Page 1 User's Guide...
Page 2: Notations Used In This Guide
Notations Used in This Guide • Safety indications The documentation and the projector use graphical symbols to show how to use the projector safely. The indications and their meaning are as follows. Make sure you understand them properly before reading the guide. Warning This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Page 3 Contact your local dealer or the nearest address provided in the "Optional Accessories" p.240 Epson Projector Contact List. Epson Projector Contact List • If you use adhesives on the ceiling mount fixing points to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its ceiling mount.
Page 4 Safety Warning and Cautions Warning Attention • Do not install the projector in a location that is subject to vibration or • Be careful when handling the power cord. Otherwise, it could cause a fire or shock. electric shock. Note the following when handling the power cord. •...
Page 5 Safety Warning and Cautions Attention Attention • Make sure you secure the following space around the projector so as not to • Use commercially available M6 screws (up to a depth of 12 mm) to fix the block the air exhaust vent and the air intake vent. projector's ceiling mount fixing points and the mount at four points.
Page 6 • If an error occurs, disconnect the power cord from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List. If you continue using the projector as it is, it could cause an electric shock, fire, or even damage to eyesight.
Page 7 Safety Warning and Cautions • About the LCD panel Warning and Cautions on the Laser - The LCD panel may contain pixels that are missing or appear bright all the time. This is not a sign of an error. Warning - When a high-powered laser beams through the surface of the projection lens even when it is not being used, it can cause a malfunction in the •...
Page 8 (Based on the RG2 IEC/EN 62471-5: 2015) • This projector may become RG3 when an interchangeable lens with throw ratio greater than 2.5 (EB-L1755U/EB-L1750U/EB-L1715S/EB-L1710S) or 3.0 (EB-L1505UH/EB-L1500UH/EB-L1515S/EB-L1510S) is installed. Refer to the manual for the lens list and hazard distance before operation. Such combinations of projector and lens are intended for professional use only, and are not intended for consumer use.
Page 9 Safety Warning and Cautions Notes on Transporting There are many glass parts and precision components inside the projector. To prevent damage due to impacts when transporting, handle the projector as follows. Caution The projector should not be carried by one person. At least two people are needed to unpack or carry the projector.
Page 10 Switching to the Target Image by Remote Control ..... . . 63 EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH ..... 34 Adjusting the Volume .
Page 11 Adjusting Image Resolution (Image Enhancement) ..... . . 87 4K Enhancement (EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH only) ..88 Scheduling Function ........116 Image Preset Mode .
Page 12 Contents Reset menu ..........164 Using the Projector on a Network Info Menu (Display Only) .
Page 13 Epson Projector Management ........218...
Page 14 Supported Monitor Displays ....... 266 EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH ..... . . 266 SDI .
Page 15: Introduction
Introduction This chapter explains the names for each part.
Page 16: Part Names And Functions
Part Names and Functions The illustrations in this guide show the lens unit attached to the projector. Name Function Projection lens Images are projected through here. Front/Top Warning Do not look into the lens while projecting. This could cause damage to eyesight due to the power‐ ful light emitted.
Page 17: Rear
Part Names and Functions Name Function Rear Lens replacement Remove when attaching or removing the lens. cover s "Removing and Attaching the Projector Lens Unit" p.28 Caution When moving the projector, do not hold the lens replacement cover. The lens replacement cover may be removed and the projector may fall, which could cause an injury.
Page 18: Interface
Part Names and Functions Name Function Interface Cable holder Insert the cable clamp for the power cord so that the power cord does not disconnect under its own weight. Interface s "Interface" p.18 Screw holes to fix the Screw holes to fix the cable cover in place. cable cover s "Attaching the Cable Cover"...
Page 19: Base
"Optional Accessories" p.240 SDI input port Inputs SDI signals from video equipment. (EB-L1755U/EB- L1750U/EB-L1505UH/ EB-L1500UH only) This is used for batch settings. This port is for control use Service port and should not normally be used.
Page 20: Control Panel
Part Names and Functions Name Function Name Function • When the Configuration menu or the Help screen is Security cable Pass a commercially available wire lock through here and ] button installation point lock it in place. displayed, it accepts and enters the current selection and moves to the next level.
Page 21: Remote Control
Part Names and Functions Name Function Remote Control • Displays the Info menu from the Configuration menu. [ ]/[ ] buttons s "Info Menu (Display Only)" p.165 • If pressed when the Configuration menu or the Help screen is displayed, this button selects menu items and setting values.
Page 22 "Switching to the Target Image by Remote Control" • When the Configuration menu or the Help screen is p.63 displayed, pressing these buttons selects menu items The [SDI] button only functions for EB-L1755U/EB- and setting values. L1750U/EB-L1505UH/EB-L1500UH. s "Using the Configuration Menu"...
Page 23 Part Names and Functions Name Function Name Function [User1] button Select any frequently used item from the Configuration [E-Zoom] buttons Enlarges or reduces the image without changing the [User2] button menu items, and assign it to any of these buttons. By [z][x] projection size.
Page 24: Handy Remote Control Operations
Part Names and Functions Name Function Operation Remote control light- Outputs remote control signals. Displaying frequently used Configuration Press the [User1], [User2], or [User3] emitting area menu items. button. You can set the menu item you want to assign to each button in User Button. s Settings - User Button p.148 The following items can be assigned.
Page 25: Remote Control Operating Range
Part Names and Functions Remove the battery cover. Replace the battery cover. While pushing the battery compartment cover catch, lift the cover Press the battery compartment cover until it clicks into place. Remote control operating range Replace the old batteries with new batteries. Caution Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way.
Page 26: Connecting A Cable To The Remote Control
Part Names and Functions To restrict reception of the operation signals from the remote control, set Remote Receiver. s Settings - Remote Receiver p.148 Connecting a cable to the remote control You can make operations securely with the optional remote control cable set when you use multiple units of this projector in the same place or when there are obstacles around the remote receiver.
Page 27: Preparing The Projector
Preparing the Projector This chapter explains how to install the projector and connect projection sources.
Page 28: Installing The Projector
Installing the Projector Removing and Attaching the Projector Lens Unit Attaching Attention • When attaching the lens unit, remove the power plug from the electrical outlet first. Hold the lock lever and turn it counterclockwise. • Do not attach the lens unit when the projector's lens insertion section is facing up.
Page 29: Lens Calibration
Check that the lens cannot be detached. remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List. Epson Projector Contact List • You can perform lens calibration using one of the following methods.
Page 30: Removing
Installing the Projector Removing Attention When replacing the lens unit, remove the power plug from the electrical outlet first. If the lens shift has been done, move the lens position to the home position before replacing the lens unit. s "Adjusting the Position of the Projected Image (Lens Shift)" p.34 The projector uses a laser as the light source.
Page 31: Screen Settings
Installing the Projector When Front is the standard, the image directions for each projection mode Screen Settings are as follows. Set the Screen Type according to the aspect ratio of the screen being used. Front (default) Front/Ceiling The area where the image is displayed matches the shape of the screen. The settings for the Screen Type at the time of purchase are as follows: •...
Page 32: Adjusting The Position Of The Image On The Projected Screen
"Changing the Aspect Ratio of the Projected Image" p.81 You can check the current display position by using the background • The Message Broadcasting function for Epson Projector Management test pattern. does not support this function. Adjusting the position of the image on the projected screen...
Page 33 Installing the Projector Standard Cross-hatching Cross-hatching Cross-hatching Press the [ ][ ] buttons on the remote control or the [ ] button on the control panel to change the test pattern. Using the remote control Using the control panel Cross-hatching Color Bars V Color Bars H Grayscale...
Page 34: Adjusting The Position Of The Projected Image (Lens Shift)
• To set menu items that cannot be set while the test pattern is being displayed or to fine-tune the projected image, project an EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH image from the connected device. • During image adjustment, press the [[][]] [Page] buttons on When using the ELPLU03/ELPLW05 the remote control to change the test pattern.
Page 35 Installing the Projector When using the ELPLX02 When using the ELPLU04/ELPLW06/ELPLM09/ELPLM10/ELPLM11/ ELPLM15/ELPLL08 Center of lens Projected image when the lens position is moved to the home position Maximum motion range: V x 20% (Top), V x 5% (Bottom) * When the horizontal direction is at the maximum value, the image Center of lens cannot be moved upward.
Page 36: Eb-L1715S/Eb-L1710S/Eb-L1515S/Eb-L1510S
Installing the Projector EB-L1715S/EB-L1710S/EB-L1515S/EB-L1510S When using the ELPLU04/ELPLW06/ELPLM09/ELPLM10/ELPLM11/ ELPLM15/ELPLL08 When using the ELPLU03/ELPLW05 Center of lens Projected image when the lens position is moved to the home position Center of lens Maximum motion range: V x 16% Projected image when the lens position is moved to the home * When the horizontal direction is at the maximum value, the image position cannot be moved vertically.
Page 37 Installing the Projector When using the ELPLX02 • When adjusting the image height with the vertical lens shift, adjust by moving the image from the bottom to the top. If it is adjusted from the top to the bottom, the image position may move down slightly after adjusting.
Page 38: Adjusting The Image Size
Installing the Projector Press the [Zoom] button on the remote control or the [Lens] Press the [ ][ ][ ] buttons to adjust the position of the button on the control panel. projected image. Repeatedly press the [Lens] button on the control panel until the Using the remote control Using the control panel zoom adjustment screen is displayed.
Page 39: Correcting The Focus
Installing the Projector Correcting the Focus When using the following lens, a message prompting you to adjust the distortion (image warping) is displayed. After adjusting the focus, adjust the distortion. Press the [Focus] button or the [Lens] button on the control ELPLX02, ELPLU03, ELPLU04, ELPLW05, ELPLU02 panel.
Page 40 Installing the Projector When using the ELPLU02, a message prompting you to manually adjust the distortion is displayed. Turn the distortion ring counterclockwise, and then adjust the focus. After adjusting the focus, manually turn the distortion ring to correct the image warping. Press the [Focus] button on the remote control or the [Lens] button on the control panel again.
Page 41: Registering And Loading Lens Adjustment Values
Installing the Projector Registering and Loading Lens Adjustment Values You can register a lens position whose lens shift, zoom, focus, and distortion was adjusted in memory, and load it when necessary. You can register up to 10 values. • This feature cannot be used if the following lenses are attached. ELPLS04, ELPLU02, ELPLR04, ELPLW04, ELPLM06, ELPLM07, ELPLL07 •...
Page 42: Adjusting The Height Of The Projected Image (For Normal Installment)
Installing the Projector Function Explanation Reset Memory Resets the name and settings of a saved memory. If the mark on the left of the memory name is turned blue, it means the memory has already been registered. When you select a registered memory, a message is displayed asking you to confirm that you want to overwrite the memory.
Page 43: Adjusting The Horizontal Tilt (For Normal Installment)
• IDs are ignored when the projector ID is set to Off or the remote control ID is set to 0. • If you use Epson Web Control, you can operate a specific projector from a mobile device. s "Changing Settings Using a Web Browser (Epson Web Control)"...
Page 44: Checking The Projector Id
Installing the Projector Select Set, and then press the [ ] button. Press the [Menu] button to close the Configuration menu. Checking the projector ID During projection, press the [ ] button while holding down the [ID] button. Remote control While holding the [ID] button, press a number button to select a number to match the ID of the projector you want to operate.
Page 45: Setting The Time
Installing the Projector Date & Time Setting the Time Submenu Function You can set the time for the projector. The set time is used for the schedule Date Set today's date. function. Set the current time. Time "Scheduling Function" p.116 Set the time difference from Coordinated Time Difference (UTC) Universal Time.
Page 46: Other Settings
Installing the Projector Press the [Menu] button to finish making settings. Other Settings Settings related to basic operations Purpose Setting Methods To start/stop projection by turning Set Direct Power On to On. (Default value: Off) on/off the main power or plugging s Extended - Operation - Direct Power in or unplugging the power plug of p.150...
Page 47: Settings Related To Display
"Reading the Indicators" p.178 Dialogs related to operations and behaviors, laser warnings, termination of Message Broadcasting for Epson Projector Management, and projector ID are displayed. To reduce the display delay of the Set Image Processing to Fast 1 or Fast 2.
Page 48: Connecting Equipment
Connecting Equipment The port name, location, and connector orientation differ depending on the source being connected. Connecting a Computer To project images from a computer, connect the computer using one of the following methods. When using a commercially available computer cable Connect the computer's display output port to the projector's Computer port.
Page 49 Connecting Equipment • Change the audio output from Audio Settings. s Extended - A/V Settings - Audio Settings p.150 • If audio is not sent using an HDMI cable, connect a commercially available audio cable to the Audio3 port to send the audio. Set HDMI Audio Output to Audio3.
Page 50: Connecting Image Sources
You can output audio from the Audio Out port on the projector by connecting the audio output port on the video equipment to the projector's Audio2 port using a commercially available audio cable. When using a commercially available BNC video cable (SDI input, EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH only) Connect the SDI port on the image source to the projector's SDI input port.
Page 51 Connecting Equipment Cb/Pb Cr/Pr Computer AUDIO OUT Audio1 Cb/Pb Cr/Pr BNC(R/Cr/Pr, G/Y, B/Cb/Pb) AUDIO OUT Audio2 HDMI OUT HDMI Attention • If the input source is on when you connect it to the projector, it could cause a malfunction. • If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction. •...
Page 52: Connecting External Equipment
Connecting Equipment Connecting External Equipment You can output images and audio by connecting an external monitor or speaker. When outputting images to an external monitor Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor. When outputting audio to an external speaker Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.
Page 53: Connecting A Lan Cable
Connecting Equipment Connecting a LAN Cable Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN cable. By connecting a computer to the projector over a network, you can project images and check the status of the projector. To prevent malfunctions, use a category 5 or higher shielded LAN cable.
Page 54: Connecting An Hdbaset Transmitter
Connecting Equipment Connecting an HDBaseT Transmitter Connect the optional HDBaseT Transmitter with a commercially available 100BASE-TX LAN cable. "Optional Accessories" p.240 HDBaseT • Make sure you read the User's Guide supplied with the HDBaseT Transmitter carefully before use. • For the LAN cable, use an HDBaseT Alliance-recommended STP cable (straight) of category 5e or higher. However, operation is not guaranteed for all input/output devices and environments.
Page 55: Installing The Wireless Lan Unit
Connecting Equipment Installing the Wireless LAN Unit Remove the air filter cover. Grip the air filter cover tab between your fingers, and pull up and remove the cover while pressing the tab. Secure the stopper with a screw. Remove the stopper for the Wireless LAN unit. Attach the air filter cover.
Page 56: Attaching The Cable Cover
Connecting Equipment Insert the tabs on the cable cover into the two slots on the back of the projector. Attaching the Cable Cover By attaching the cable cover, you can hide the connected cables giving a nice, clean finish to the projector installation. (The illustrations are of a projector installed on a ceiling.) Warning Do not tie the power cord and other connection cables together.
Page 57 Connecting Equipment...
Page 58: Basic Usage
Basic Usage This chapter explains how to project and adjust images.
Page 59: Turning On The Projector
Turning On the Projector Before turning on the projector, connect your computer or video equipment Warning to the projector. • Do not look into the projector's lens during projection. Doing so may "Connecting Equipment" p.48 damage your eyes. Be especially careful if children are present. •...
Page 60 Turning On the Projector When the Home screen is displayed, use the [ ][ ][ ] buttons on Select Color Mode. the control panel or remote control to select an item, and then press the s "Selecting the Projection Quality (Selecting Color Mode)" p.77 ] button.
Page 61: Turning Off The Projector
Turning Off the Projector • To ensure a long projector service life, turn off the projector when you are not using it. The light source's operating life varies depending on the Configuration menu settings, environmental conditions, and usage conditions. The brightness of the projected image drops as projection time elapses.
Page 62: Projecting Images
Using the remote control Using the control panel *EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH only When two or more image sources are connected, repeatedly press the [Search] button until the target image is projected. When your video equipment is connected, start playback before beginning...
Page 63: Switching To The Target Image By Remote Control
The input ports for the buttons are shown below. Remote control Select the input source to be projected, and then press the [ ] button. Input Port Changes to images from a computer connected via the network. For EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH only.
Page 64: Adjusting The Volume
Projecting Images Adjusting the Volume You can adjust the volume of the audio from the Audio Out port using one of the following methods. • Press the [Volume] buttons on the remote control to adjust the volume. ] Increases the volume. ] Decreases the volume.
Page 65: Adjusting Projected Images
Adjusting Projected Images • Curved Surface Correcting Distortion in the Projected Image Correct distortion that occurs when projecting on a curved surface, and adjust the amount of expansion and contraction. You can correct keystone distortion in projected images using one of the "Curved Surface"...
Page 66: H/V-Keystone
Adjusting Projected Images • By pressing the [Geometry] button on the remote control or the ] button on the control panel, a screen for selecting the adjustment method is displayed. • When you want to re-adjust the projection position and so on, if you want to release the correction status temporarily, set the Geometry Correction to Off.
Page 67: Quick Corner
Adjusting Projected Images Correct the keystone distortion by using V-Keystone and H- You cannot combine with other correction methods. Keystone. V-Keystone Quick Corner This allows you to correct each of the four corners of the projected image independently. H-Keystone Press the [Menu] button while projecting. Select Geometry Correction from Settings.
Page 68: Curved Surface
• If a large amount of adjustment is performed, the focus may not be uniform even after making adjustments. • If 4K Enhancement is enabled, a message is displayed. Select Yes to disable 4K Enhancement. (EB-L1755U/EB-L1750U/EB-L1505UH/EB- L1500UH only) s Image - Image Enhancement - 4K Enhancement...
Page 69 Adjusting Projected Images Use the following to check the adjustment range for the image. Select Correct Shape, and then press the [ ] button. "Curved Surface" p.257 Press the [Menu] button while projecting. Select Geometry Correction from Settings. Select Curved Surface, and then press the [ ] button.
Page 70 Adjusting Projected Images Use the [ ], [ ], [ ], and [ ] buttons to select the area you Use the [ ], [ ], [ ], and [ ] buttons to adjust the shape. want to adjust, and then press the [ ] button.
Page 71 Adjusting Projected Images Press the [Esc] button to display the screen from step 5. Select Adjust the linearity. Horizontal Linearity or Vertical Linearity, and then press the [ Correct it so that the distance between lines is equal. button. When pressing the [ ] button When Horizontal Linearity is selected When Vertical Linearity is selected Select Horizontal Linearity to adjust the horizontal expansion or contraction, and select Vertical Linearity to adjust the vertical...
Page 72: Corner Wall
• If 4K Enhancement is enabled, a message is displayed. Select Yes to "If this setting is changed, the image may be distorted." is displayed, disable 4K Enhancement. (EB-L1755U/EB-L1750U/EB-L1505UH/EB- press the [ ] button again.
Page 73 Adjusting Projected Images Adjust the position of the projector and the lens shift so that the According to the projection area, select Horizontal Corner or line in the center of the screen matches the corner (the point Vertical Corner, and then press the [ ] button.
Page 74 Adjusting Projected Images When Vertical Corner is selected: Use the [ ], [ ], [ ], and [ ] buttons to select the area you Adjust the left and right based on the point nearest to the vertical want to adjust, and then press the [ ] button.
Page 75: Point Correction
32 pixels. EB-L1715S/EB-L1710S/EB-L1515S/EB-L1510S: Vertical and horizontal up to a maximum of 27 pixels. • If 4K Enhancement is enabled, a message is displayed. Select Yes to disable 4K Enhancement. (EB-L1755U/EB-L1750U/EB-L1505UH/EB- L1500UH only) s Image - Image Enhancement - 4K Enhancement p.143...
Page 76 Adjusting Projected Images "If this setting is changed, the image may be distorted." is displayed, Use the [ ], [ ], [ ], and [ ] buttons to move to the point you press the [ ] button again. want to correct, and then press the [ ] button.
Page 77: Selecting The Projection Quality (Selecting Color Mode)
Adjusting Projected Images Each time you press the [Color Mode] button, the Color Mode name is You can fine tune the corrected results. Select Quick Corner on the displayed on the screen and the Color Mode changes. screen from step 4 to adjust the tilt of the image. Remote control s "Quick Corner"...
Page 78 Custom: Select this to set the Brightness Level manually. When Custom is selected, Constant Brightness is available. When the following lenses are attached to EB-L1755U/EB- L1750U/EB-L1715S/EB-L1710S, brightness is restricted and you Select Light Source Mode, and then press the [ ] button.
Page 79: Guide To Estimated Remains
Adjusting Projected Images Display Level Estimated Remains • When Constant Brightness is set to On, you cannot change the settings for Light Source Mode and Brightness Level. 10,000 hours or more When you want to change these settings, set Constant 8,000 to 9,999 hours Brightness to Off.
Page 80: Setting The Amount Of Light Of The Projected Image
Adjusting Projected Images Illustration Setting the Amount of Light of the Projected 61,000 hours Image 71,000 hours By automatically setting the luminance according to the brightness of the displayed image, it lets you enjoy deep and rich images. When Constant Brightness is set to On : Brightness Level Dynamic Contrast can only be set when the Color Mode is set to : Approximate time for which constant brightness of the light source can...
Page 81: Changing The Aspect Ratio Of The Projected Image
Projects while retaining the aspect ratio of the input image. mode setting. Projects at an aspect ratio of 4:3. Projects at an aspect ratio of 16:9. 16:9 EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH Full Projects at the full size of the projected screen. Screen type setting: 16:10...
Page 82 Adjusting Projected Images Aspect Ratio of Input Signal Aspect Ratio of Input Signal 16:10 16:9 16:10 16:9 Auto or Normal Full 16:9 H-Zoom Full V-Zoom H-Zoom Native V-Zoom The image may differ depending on the resolution of the input signal. Screen type setting: 4:3 Aspect Ratio of Input Signal Native...
Page 83 Adjusting Projected Images Aspect Ratio of Input Signal Aspect Ratio of Input Signal 16:10 16:9 16:10 16:9 H-Zoom H-Zoom V-Zoom V-Zoom Native Native *1 When inputting an HDTV signal (720p/1080i/1080p), the aspect ratio of the signal is maintained, while the image is trimmed on the left and right and *1 When inputting an HDTV signal (720p/1080i/1080p), the aspect ratio of the displayed.
Page 84: Adjusting The Image
Adjusting Projected Images Aspect Ratio of Input Signal Adjusting the Image 16:10 16:9 Native Hue, Saturation, and Brightness adjustment You can adjust the Hue (tint), Saturation (vividness), and Brightness of the six axes R (red), G (green), B (blue), C (cyan), M (magenta), and Y The image may differ depending on the resolution of the input signal.
Page 85: Gamma Adjustment
Adjusting Projected Images Adjust by projecting a still picture. Gamma cannot be adjusted correctly by using movies. Select and adjust the correction value Press the [Menu] button while projecting. Select Advanced from Image, and then press the [ ] button. Use the [ ] buttons to select the item, and then use the [ ][ ] buttons to make the adjustments.
Page 86 Adjusting Projected Images When a larger value is selected, the dark areas of images become brighter, but the color saturation for lighter areas may become weaker. When a smaller value is selected, you can reduce the overall brightness of the image to make the image sharper. Select Gamma, and then press the [ ] button.
Page 87: Frame Interpolation
Adjusting Projected Images Select Frame Interpolation from Image, and then press the [ button. When Do you want to continue adjusting the setting? is displayed, select Yes or No. To adjust another tone, select Yes, and repeat the procedure from step 5.
Page 88: K Enhancement (Eb-L1755U/Eb-L1750U/Eb-L1505Uh/Eb-L1500Uh Only)
Image Preset Mode. • To project from multiple projectors, select Off to unify each 4K Enhancement (EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH image. only) • Off is ideal for projecting presentation materials from computers and so on.
Page 89: Image Preset Mode
Adjusting Projected Images Image Preset Mode Noise Reduction Select the optimal setting according to the projected image from five presets You can smooth out rough images for softer image quality when inputting prepared in advance. progressive signals or progressive interlace signals. The following settings are saved in the presets.
Page 90: Super-Resolution
Adjusting Projected Images Select MPEG Noise Reduction from Image Enhancement, and Use the [ ] buttons to select the item, and then use the then press the [ ] button. [ ][ ] buttons to make the adjustments. Fine Line Adjust: If this parameter is set to a positive value, details Select a level to reduce noise from Low, Normal, or High, and such as hair or fabric patterns will be enhanced.
Page 91: Projecting 3D Images (Eb-L1505Uh/Eb-L1500Uh/Eb-L1515S/Eb-L1510S Only)
Adjusting Projected Images Use the [ ] buttons to select the item, and then use the [ ][ ] buttons to make the adjustments. Strength: The larger the value, the more the contrast is enhanced. Range: The larger the value, the wider the range of detail enhancement becomes.
Page 92: Useful Functions
Useful Functions This section describes the Multi-Projection, Split Screen, Memory, Schedule, and Security functions.
Page 93: Multi-Projection Function
Brightness Level to the brightness you want to use. Also, set this projector as the master projector. • Set 4K Enhancement to Off. (EB-L1755U/EB-L1750U/EB-L1505UH/ Settings - Brightness Settings - Light Source Mode - Brightness Level EB-L1500UH only) p.148...
Page 94: Adjusting Manually Offline
Multi-Projection Function Adjusting the projected images Adjust the lens shift. s "Adjusting the Position of the Projected Image (Lens Shift)" p.34 "Adjusting the projected images" p.93 Adjust the zoom and focus. s "Adjusting the Image Size" p.38 s "Correcting the Focus" p.39 Tiling Adjust small differences in the images.
Page 95 Multi-Projection Function Press the [Menu] button while projecting. Select Multi-Projection from Extended, and then press the [ button. Select Projector Grouping, and then press the [ ] button. Select the projectors that will be used for tiling, and then press the Select Location Setup, and then press the [ ] button.
Page 96: Performing Tiling Manually
Multi-Projection Function Select Multi-Projection from Extended, and then press the [ If the image is not located correctly, select Manual in step 6, button. and then follow the steps below to locate the image manually. (1) Set Row and Column in Layout. Select Tiling, and then press the [ ] button.
Page 97: Edge Blending
Multi-Projection Function When tiling is complete, adjust any positional gaps and the tint of the projected images. "Adjusting the projected images" p.93 Edge Blending You can fine tune the overlapping areas to make seamless screen. Submenu Function Set to On to activate Edge Blending. Set to Off Edge Blending Before performing edge blending to raise the precision of adjustments, when not projecting from multiple projectors.
Page 98 Multi-Projection Function Turn on Edge Blending. In the example above, you need to adjust the Left Edge because you can see the overlapping areas on the left side of the image (1). Select Edge Blending, and then press the [ ] button.
Page 99: Black Level
Multi-Projection Function Select Black Level from Multi-Projection, and then press the [ Black Level button. When a black image is displayed, only areas where the images overlap stands out. The black level function allows you to match the brightness and tone for areas where the images do not overlap with areas where the images overlap, to make the difference less noticeable.
Page 100 Multi-Projection Function Select the area you want to adjust, and then press the [ button. The selected area is displayed in orange. When multiple screens are overlapping, adjust based on the area with the most overlap (the brightest area). In the illustration below, first align (2) with (1), and then adjust so that (3) aligns After this, if the tone for some areas do not match, adjust them by with (2).
Page 101 Multi-Projection Function Use the [ ][ ][ ] buttons to adjust the boundary line positions, and then press the [ ] button. Press the [ ][ ][ ] buttons to select the point you want to move, and then press the [ ] button.
Page 102: Screen Matching
Multi-Projection Function To complete the adjustment, press the [Menu] button. • We recommend performing Screen Matching 20 minutes after turning on the projector or canceling A/V mute. • To increase the accuracy of adjustments, we recommend darkening Screen Matching the room while projecting images and then making adjustments. •...
Page 103: Automatically Correct The Brightness And Tint For Multiple Projectors
Select Start Auto Adjustment, and then press the [ ] button. • Auto adjustment is not available when using the following lenses. ELPLX02, ELPLR04, ELPLL08, ELPLL07/ ELPLU03, ELPLU04, ELPLU02 (EB-L1755U/EB-L1750U/EB-L1715S/ EB-L1710S) • After auto adjustment, the movement range for lens shift is reduced for some lenses.
Page 104: Color Matching
Multi-Projection Function The following screen is displayed. Color Matching You can fine tune the color balance and brightness from black to white for each color tone. When the projectors are not connected to a network, or if you want to adjust manually after the automatic adjustments, perform the following steps on all projectors.
Page 105: Displaying A Scaled Image
Multi-Projection Function Return to step 2 and adjust each level. Turn on Scale. Select Scale, and then press the [ ] button. Press the [Esc] button to return to the previous screen. Select Auto or Manual, and then press the [ ] button.
Page 106 Multi-Projection Function Adjust the scale. Select Zoom Display or Full Display, and then press the [ ] button. Zoom Display: Adjusts according to the image currently displayed. Select the adjustment method with the [ ] buttons, then adjust Enlarge using the [ ][ ] buttons. -+: Enlarges or reduces an image horizontally and vertically at the same time.
Page 107: Projection Functions
DVI-D Computer EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH only • Signals that exceed WUXGA are not supported. • If 4K Enhancement is enabled, a message is displayed. Select Yes to disable 4K Enhancement. (EB-L1755U/EB-L1750U/EB-L1505UH/EB- L1500UH only) s Image - Image Enhancement - 4K Enhancement p.143...
Page 108: Operating Procedures
Projection Functions Operating procedures Select Source, and then press the [ ] button. Select each input source for Left and Right. Projecting on a split screen Press the [Split] button on the remote control while projecting. The currently selected input source is projected on the left of the screen.
Page 109 Projection Functions The projected images will appear as shown below after setting the screen Select Swap Screens, and then press the [ ] button. size. The projected images on the left and right are swapped. Equal Larger Left Switching the left and right image sizes Larger Right Press the [Menu] button during split screen projection.
Page 110: Restrictions During Split Screen Projection
Projection Functions Restriction relating to images Select the audio you want to output, and then press the [ button. • For the image on the right screen, the default values for the Image When you select Auto, audio is output for the enlarged screen. If the menu are applied.
Page 111: Freezing The Image (Freeze)
Projection Functions • If you want to fade out or fade in when turning the video on or off, Freezing the Image (Freeze) set the desired number of seconds in Fade-out and Fade-in. When Freeze is activated on moving images, the frozen image continues to s Extended - Operation - A/V Mute Settings - Fade-out, Fade-in p.150 project on the screen, so you can project a moving image one frame at a...
Page 112: Enlarging Part Of The Image (E-Zoom)
Press the [ ] button to display the Cross ( • If 4K Enhancement is enabled, a message is displayed. Select Yes to disable 4K Enhancement. (EB-L1755U/EB-L1750U/EB- Remote control L1505UH/EB-L1500UH only) s Image - Image Enhancement - 4K Enhancement p.143...
Page 113: Saving A User's Logo
Projection Functions Move the box to select the part of the image to use as the User's Saving a User's Logo Logo. You can perform the same operations from the projector's control You can save the image that is currently being projected as a User's Logo. panel.
Page 114: Memory Function
Memory Function The settings for the image currently displayed and values for geometry correction are saved as a memory, allowing you to load them when necessary. Saving/Loading/Erasing/Resetting the Memory Press the [Memory] button while projecting. Remote control Memory: Settings for the following menu items are saved in the memory.
Page 115 Memory Function Function Explanation Reset Memory Resets the name and settings of a saved memory. To reset all memories saved in Memory, Lens Position, and Geometry Correction, use Reset All Memories. s Reset - Reset All Memories p.167 If the mark on the left of the memory name is turned blue, it means the memory has already been registered.
Page 116: Scheduling Function
Scheduling Function You can schedule turning the projector power on/off and switching the Set the schedule. input source, as events in the schedule. Registered events are executed Submenu Name Function automatically at the specified time on the specified dates or weekly. Event Settings Select an operation of the projector when the event You can register up to 30 events in Schedule, and one event in Extended...
Page 117: Checking An Event
Scheduling Function Checking an Event This section explains how to check a Schedule event. Press the [Menu] button while projecting. Select Schedule Settings from Extended. The indicator turns on when an event is saved. • Light source calibration does not start automatically when the projector is used continuously for more than 24 hours, or when direct shutdown is used regularly.
Page 118: Editing An Event
Scheduling Function Press the [ ][ ] buttons to highlight the date you want to check. The details of the events registered on the selected date are displayed. Highlight the event you want to edit, and then press the [Esc] button.
Page 119 Scheduling Function Submenu Name Function Edit Edits the content of the selected event. Select Save, and then press the [ ] button to complete the editing. Clear Deletes the selected event. Saves a new event. Select Save, and then press the Add New ] button to complete registering.
Page 120: Security Functions
Security Functions • User's Logo Protection The projector has the following enhanced security functions. Even if someone tries to change the User's Logo set by the owner of the • Password protect projector, it cannot be changed. When User's Logo Protection is set to You can limit who can use the projector.
Page 121: Entering The Password
Security Functions During projection, hold down the [Freeze] button for about five Set the password. seconds. Select Password, and then press the [ ] button. The Password Protection setting menu is displayed. When the message "Change the password?" is displayed, select Yes and Remote control then press the [ ] button.
Page 122: Restricting Operation
• Partial Lock projector does not accept any more password entries. "The projector's operation will be locked. Contact Epson as described in your documentation." All of the buttons on the control panel, except for the [ ] button, are Epson Projector Contact List locked.
Page 123: Lens Lock
Security Functions You can also make settings in Control Panel Lock from the configuration menu. s Settings - Lock Setting - Control Panel Lock p.148 Select either Full Lock or Partial Lock according to your purpose. Set the Lens Lock to On in the Configuration menu. Settings - Lock Setting - Lens Lock p.148 Remote control button lock...
Page 124: Anti-Theft Lock
Security Functions Each time the [ ] button is pressed for approximately 5 seconds, the Installing the wire lock remote control button lock turns on or off. Pass an anti-theft wire lock through the installation point. Remote control See the documentation supplied with the wire lock for locking instructions. Even if the remote control button lock is on, the following operations are possible.
Page 125: Using The Projector On A Network
Using the Projector on a Network Follow the instructions in these sections to set up your projector for use on a network.
Page 126: Wired Network Projection
After connecting and setting up the projector, install Epson iProjection from the Epson Projector Software CD-ROM (if available) or Web site. Epson iProjection software sets up your computer for network projection. It also allows you to hold interactive meetings by projecting user's computer screens over a network.
Page 127 • Remote Password: Lets you set an authentication password for using the Remote function in Epson Web Control when setting or controlling the projector. You can enter up to 8 single-byte alphanumeric characters. (The user name is EPSONREMOTE; the default password is guest.)
Page 128 Wired Network Projection If you have finished making settings, select Setup complete. Follow the on-screen instructions to save the settings and close the menu. Press the [LAN] button on the remote control. The wired network settings complete when you see the correct IP address on the LAN standby screen.
Page 129: Wireless Network Projection
You can send images to your projector through a wireless network. Selecting Wireless Network Settings Manually To do this, you must install the Epson 802.11b/g/n wireless LAN module, and then set up your projector and computer for wireless projection. Before you can project from your wireless network, you need to select network settings for the projector.
Page 130 You can enter up to 32 single-byte alphanumeric characters. • Remote Password: Lets you set a password for accessing the projector using Remote in Epson Web Control. You can enter up to 8 single-byte alphanumeric characters. (The user name is EPSONREMOTE; the default password is guest.) •...
Page 131 Wireless Network Projection Select the Connection Mode setting. Press the [LAN] button on the remote control. The wired network settings complete when you see the correct IP • Quick lets you connect to multiple smartphones, tablets, or address on the LAN standby screen. computers directly using wireless communication.
Page 132: Selecting Wireless Network Settings In Windows
Wireless Network Projection Selecting Wireless Network Settings in Windows Setting Up Wireless Network Security Before connecting to the projector, select the correct wireless network on You can set up security for your projector to use on a wireless network. Set your computer.
Page 133 Wireless Network Projection • WPA2-PSK, WPA/WPA2-PSK: Select the Wireless LAN menu and press [Enter]. Select Setup complete. Follow the on-screen instructions to save the settings and close the menu. • WPA2-EAP, WPA/WPA2-EAP: Select EAP Method and press [Enter]. Select the protocol for authentication as the EAP Type setting. To import your certificate, select the certificate type and press [Enter].
Page 134: Supported Client And Ca Certificates
32 characters, use your Web browser to enter the text. • RADIUS Serv.Name lets you enter the server name to be verified. "Changing Settings Using a Web Browser (Epson Web Control)" p.218 If you have finished making settings, select Setup complete.
Page 135: Using A Qr Code To Connect A Mobile Device
(Epson iProjection V1.3.0 or later supports this feature). • You can download Epson iProjection for free from the App Store or Google Play. Any fees incurred when communicating with the App Store or Google Play are the responsibility of the customer.
Page 136: Using A Usb Key To Connect A Windows Computer
• If it is not installed automatically, double-click MPPLaunch.exe in the USB key. Set up the USB key using Epson iProjection (Windows/Mac). See the Epson iProjection Operation Guide (Windows/Mac) for instructions. After a few minutes, your computer image is displayed by the projector.
Page 137: Secure Http
Secure HTTP You can use the HTTPS protocol to increase security between the projector Importing a Web Server Certificate Using the and a Web browser communicating with it. To do this, you create a server Menus certificate, install it on the projector, and turn on the Secure HTTP setting in the projector menus to verify the reliability of the Web browser.
Page 138: Supported Web Server Certificates
Secure HTTP Select the Others menu and press [Enter]. Enter a password and press [Enter]. The certificate is imported and a completion message appears. Supported Web Server Certificates You can register these types of digital certificates. Web Server Certificate (Secure HTTP) Item Explanation Format...
Page 139: Configuration Menu
Configuration Menu This chapter explains how to use the Configuration menu and its functions.
Page 140: Using The Configuration Menu
Using the Configuration Menu This section explains how to use the Configuration menu. Select a submenu item. Although steps are explained using the remote control as an example, you can perform the same operations from the control panel. Check the guide under the menu for the available buttons and their operations.
Page 141: List Of Functions
List of Functions Top Menu Name Submenu Name Items or Setting Values Configuration Menu Table Auto Setup On, Off Settable items vary depending on the model being used and the image Overscan Auto, Off, 4%, and 8% signal and source being projected. Blanking Top, Bottom, Left, and Right Top Menu Name...
Page 142: Network Menu
List of Functions Top Menu Name Submenu Name Items or Setting Values Top Menu Name Submenu Name Items or Setting Values Display Menu Position, Message Position, Info menu Projector Info Total Op. Time, Operation Hours, Messages, Display Background, Sources, Input Signal, Resolution, p.165 Startup Screen, Standby Refresh Rate, Sync Info, Status,...
Page 143: Image Menu
List of Functions Top Menu Name Submenu Name Items or Setting Values Top Menu Name Submenu Name Items or Setting Values Search Access Point Address 1 Setting, Email Address, No Signal, Address 2 Setting, System Error, Laser Error, SSID Address 3 Setting High Temp Error, Air Security Open, WPA2-PSK,...
Page 144 List of Functions "Automatically Detecting Input Signals and Changing the Projected Submenu Function Image (Source Search)" p.62 Sharpness Standard: You can adjust the image sharpness. Thin Line Enhancement: If this parameter is set to a positive value, details such as hair or fabric patterns will be enhanced.
Page 145 "Reset Menu" p.167 4K Enhancement : (EB-L1755U/EB-L1750U/EB-L1505UH/ EB-L1500UH only) You can project at a doubled resolution. *1 This cannot be set when E-Zoom is used. Image Preset Mode: You can select the optimal setting *2 This cannot be set when inputting signals whose resolution is higher than that according to the projected image from five presets prepared of WUXGA signals or when 4K Enhancement is enabled.
Page 146: Signal Menu
List of Functions Submenu Function Signal Menu Sync. (Only available when an analog RGB computer signal is being Settable items vary depending on the image signal and source currently input.) being projected. Setting details are saved for each image signal. You can adjust computer images when flickering, fuzziness, or interference appear in the images.
Page 147 List of Functions Submenu Function Submenu Function Advanced You can set by choosing the following items. Reset You can reset all adjustment values on the Signal menu to their default settings, except for Input Signal and EDID. Video Range: Select the video range for the input signal from the HDMI port, DVI-D port, HDBaseT port, or SDI.
Page 148: Settings Menu
List of Functions Submenu Function Settings Menu Geometry Cor- You can correct distortion. rection s "Correcting Distortion in the Projected Image" p.65 • Off: Temporarily cancels the geometry correction. • H/V-Keystone: Adjust V-Keystone, V-Balance, H-Keystone, and H- Balance to correct vertical and horizontal keystone distortion.
Page 149 List of Functions Submenu Function Submenu Function Lock Setting Control Panel Lock: You can use this to restrict operation of the Remote Receiver You can limit the reception of the operation signal from the projector's control panel. remote control. s "Control Panel Lock" p.122 When set to Off, you cannot perform any operations from the remote control.
Page 150: Extended Menu
List of Functions Submenu Function Extended Menu Display You can make settings related to the projector's display. Menu Position: Select the position to display the menu on the projected screen. Message Position: Select the position to display the message on the projected screen. Messages: When set to Off, the following items will not be displayed.
Page 151 List of Functions Submenu Function Submenu Function User's Logo You can change the user's logo that is displayed as a Operation Direct Power On: Set to On to turn on the projector background during Display Background, A/V Mute, and so simply by plugging it in.
Page 152 When Simple is selected, you • Lens Type: When using the following lens, select the can use the remote control provided with other Epson model number of the lens. projectors to operate this projector. This is useful if you...
Page 153 List of Functions Submenu Function Submenu Function A/V Settings A/V Output: Set this to Always On if you want to output Standby Mode Standby Mode: If you set this to Communication On, you audio and images to an external device even when the can perform the following operations even if the projector is projector is in standby status.
Page 154 List of Functions Submenu Function Submenu Function HDBaseT Control Communications: (This cannot be set when Multi-Projection Make settings when projecting from multiple projectors. Extron XTP is set to On.) When set to On, Ethernet s "Multi-Projection Function" p.93 communication, serial communication, and the wired Projector ID: Set the ID from 01 to 30.
Page 155: Network Menu
List of Functions Submenu Function Network Menu Reset You can reset all adjustment values for the Extended menu to their default settings. However, the following items are When Network Protection is set to On in Password Protection, a message not reset. is displayed and the network settings cannot be changed.
Page 156: Notes On Operating The Network Menu
Remote Camera • Antenna Level location. You can also set a password when shooting images Access • Projector Name using remote camera access from Epson Web Control. • SSID s "Checking the projected image from a remote location" • DHCP p.224 •...
Page 157: Soft Keyboard Operations
The following types of character can be entered. s "About PJLink" p.230 0123456789 Numbers Set a password to use Remote in Epson Web Control. You can Remote Pass- Letters ABCDEFGHIJKLMNOPQRSTUVWXYZ word enter up to 8 single-byte alphanumeric characters. (* : and spaces cannot be used.) The default user name is "EPSONREMOTE"...
Page 158: Wireless Lan Menu
QR code, you can connect to a network just by Set the connection mode to use when connecting the Connection reading the QR code in Epson iProjection. Text & QR Code is set projector and a computer via a wireless LAN. Mode by default.
Page 159 When entering more than 32 characters, use your WPA2-EAP*: Communication is performed using WPA2 Web browser to enter the text. security. Uses AES method for encryption. s "Changing Settings Using a Web Browser (Epson Web WPA/WPA2-EAP*: Connects in WPA enterprise mode. Control)" p.218...
Page 160 - PJLink server. You can enter up to 32 single-byte alphanumeric • When setting the IPv6 address manually, characters. make settings in Advanced from Epson You can select the channels used to connect in Quick mode. Web Control. Channel If interference from other signals occurs, use a different s "Changing Settings Using a Web...
Page 161 List of Functions WPA is an encryption standard that improves the security for wireless Submenu Function networks. The projector supports TKIP and AES encryption methods. Indicates the access points where security is set. WPA also includes user authentication functions. WPA authentication If you select an access point where security has not been set, the provides two methods: using an authentication server, or authenticating Wireless LAN menu is displayed.
Page 162: Wired Lan Menu
• The following functions support IPv6 proto‐ cols. - Epson Web Control - PJLink • When setting the IPv6 address manually, make settings in Advanced from Epson Web Control. s "Changing Settings Using a Web Browser (Epson Web Control)" p.218...
Page 163 Configuration menu. When entering more than 32 characters, use your Web browser to enter the text. ( " ( ) , : ; < > [ \ ] and spaces cannot be used.) s "Changing Settings Using a Web Browser (Epson Web Control)" p.218 Set to On to monitor the projector using SNMP .
Page 164: Others Menu
Universe. To strengthen security, communication between the projector Secure HTTP and computer in Epson Web Control is encrypted. When setting Start Channel: Sets the start channel that handles Art-Net. security with Epson Web Control, we recommend setting this to s "Channel definitions"...
Page 165: Info Menu (Display Only)
List of Functions Info Menu (Display Only) Lets you check the status of the image signals being projected and the status of the projector. Items that can be displayed vary depending on the source currently being projected. Submenu Function Reset network To reset all of the Network settings, select Yes.
Page 166 List of Functions Submenu Function Submenu Function Status This is information about errors that have Voltage Warning Info Displays up to 10 instances of voltage occurred on the projector. warnings. When you select Detail when a Warning or Error is displayed, you can This information may be needed if service check detailed logs for before and after the is required.
Page 167: Reset Menu
List of Functions Reset Menu Submenu Function Reset All Memo- Resets all names and settings saved in Memory, Lens Position, ries and Geometry Correction. s "Memory Function" p.114 You can reset all items in the Configuration menu to their default Reset All Config settings.
Page 168: Batch Setup
Batch Setup Once the Configuration menu content has been set for one projector, you Setup Using a USB Flash Drive can use it to perform batch setup for multiple projectors (batch setup function). The batch setup function is only for projectors with the same This section explains how to perform batch setup using a USB flash drive.
Page 169 Batch Setup When the projector's indicators turn on as follows, release the [Esc] • Connect the USB flash drive directly to the projector. If the button. USB flash drive is connected to the projector through a USB hub, the settings may not be saved correctly. •...
Page 170: Reflecting Saved Settings To Other Projectors
Batch Setup Reflecting saved settings to other projectors When writing completes normally, the projector enters standby Disconnect the power cord from the projector, and check that all status. of the projector's indicators have turned off. Connect the USB flash drive containing the saved batch setup file to the projector's wireless LAN unit port.
Page 171 Batch Setup While holding down the [Menu] on the remote control or the Caution control panel, connect the power cord to the projector. • Do not disconnect the power cord from the projector while the settings are being written. If the power cord is disconnected, the projector may not start correctly.
Page 172: Setup By Connecting The Computer And Projector With A Usb Cable
Batch Setup When the projector's indicators turn on as follows, release the [Esc] Setup by Connecting the Computer and Projector button. with a USB Cable The following operating systems support the batch setup function. • Windows Vista or later • Mac OS X 10.7.x or later Saving settings to a computer Power supply Status Laser...
Page 173: Reflecting Saved Settings To Other Projectors
Batch Setup While holding down the [Menu] on the remote control or the Reflecting saved settings to other projectors control panel, connect the power cord to the projector. Disconnect the power cord from the projector, and check that all of the projector's indicators have turned off. Connect the computer's USB port to the projector's Service port with a USB cable.
Page 174: When Setup Fails
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List. Epson Projector Contact List Power: Blue - flashing fast...
Page 175: Troubleshooting
Troubleshooting This chapter explains how to identify problems and what to do if a problem is found.
Page 176: Using The Help
Using the Help If a problem occurs with the projector, you can display the Help screen to assist you. You can also set the projector to an appropriate state by answering the questions. Press the [ ] button. The Home screen is displayed. Remote control Select a menu item.
Page 177 Using the Help See the following if the Help function does not provide a solution to the problem. s "Reading the Indicators" p.178...
Page 178: Reading The Indicators
Reading the Indicators This projector has the following five indicators to indicate the projector's status. Power indicator Indicates the projector's status. Status indicator Indicates the projector's status. Laser indicator Indicates the light source status. Temp indicator Indicates the internal temperature status. This is normally turned off. Filter indicator Indicates the air filter status.
Page 179 Reading the Indicators Indicator Projector's Sta- Explanation Power Status Laser Temp Filter supply Projecting The projector is projecting. Blue - On Blue - On Status varies Cool down status This is the status immediately after turning off the power. In this status, all buttons are disabled. Blue - Blue - On Flashing...
Page 180 If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List. Epson Projector Contact List When using at an altitude of 1500 m or more, set High Altitude Mode to On.
Page 181 After checking, connect the power cord to the electrical outlet. If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
Page 182 If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List. Epson Projector Contact List Air Filter Notice "Time to clean the air filter.
Page 183 • If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
Page 184: Reading The Status Display
Reading the Status Display You can display the operating status of the projector on the projected image. You can check the detailed status of the projector by using button operations. Press the [ ] button while projecting. Remote control Control panel Each display category contains the following information.
Page 185: Explanations Of The Display Content
Reading the Status Display Explanations of the Display Content Category Item Status Display Explanation Status Information System Displays the projector's status. See the following for more information on how to remedy the errors and warnings. s "Reading the Indicators" p.178 The projector is in normal status.
Page 186 Reading the Status Display Category Item Status Display Explanation Status Information Source HDMI Displays the source name for the connected equipment currently being projected. HDBaseT DVI-D Computer On-Screen Display Displays the settings for the On-Screen Display. When set to Off, the menus or messages are not displayed on the projected images.
Page 187 Reading the Status Display Category Item Status Display Explanation <Warning2> Power flicker: If the input voltage drops below 85 V for more than 40 msec, and the voltage returns within 60 msec, logs for approximately one second before the power flicker was detected (60 logs) and for approximately 0.1 seconds after (6 logs) are displayed.
Page 188 Reading the Status Display Category Item Status Display Explanation Source Video Signal Displays the current input video signal. Color Space Displays the color space of the current input signal. YCbCr YPbPr H-Frequency Displays the horizontal frequency of the current input signal. V-Frequency Displays the vertical frequency of the current input signal.
Page 189 Reading the Status Display Category Item Status Display Explanation Signal Information 5V Detection Detected Displays the detection results of 5V signals. Not Detect TMDS Clock Displays the TMDS frequency of the current input signal. TMDS H-Frequency Displays the horizontal frequency of the current input signal. TMDS V-Frequency Displays the vertical frequency of the current input signal.
Page 190 Reading the Status Display Category Item Status Display Explanation Network Wired Projector Name Displays the projector name used to identify the projector when connected to a network. Connection Mode HDBaseT Displays the connection path for LAN. DHCP Displays the DHCP settings. IP Display Displays the IP address display settings.
Page 191 Reading the Status Display Category Item Status Display Explanation Maintenance Operation Time Displays the total operation time of the projector. Laser Op.Time Displays the laser operating time for each setting in Light Source Mode. Version Serial No. Displays the projector's serial number. Main Displays the projector's firmware version information.
Page 192: Problem Solving
Problem Solving If any of the following problems occur and the indicators do not offer a • The remote control does not work sp.201 solution, refer to the pages given for each problem. • Nothing appears on the external monitor sp.202 Problems Relating to Images •...
Page 193: Problems Relating To Images
Problem Solving Problems Relating to Images No images appear Check Remedy Did you press the [ ] button on the remote control or control Press the [ ] button to turn on the power. panel? Are the indicators switched off? The power cord is not connected correctly or power is not being supplied.
Page 194: Moving Images Are Not Displayed
Problem Solving Moving images are not displayed Check Remedy Is the computer's image signal being output to the LCD and the Change the image signal from the computer to external output only. Check your computer's documentation, or contact monitor? the computer's manufacturer. (Only when projecting images from a laptop computer or a computer with a built-in LCD screen) Are the contents of the moving image you are trying to project...
Page 195: No Signal. Is Displayed
Problem Solving "No Signal." is displayed Check Remedy Are the cables connected correctly? Check that all the cables required for projection are securely connected. Check that no cables are disconnected and that there are no poor contacts in the cables. Is the correct port selected? Change the image by pressing the [Search] button.
Page 196: Interference Or Distortion Appear In Images
Problem Solving Interference or distortion appear in images Check Remedy Are the cables connected correctly? Check that all the cables required for projection are securely connected. s "Connecting Equipment" p.48 Is an extension cable being used? If an extension cable is used, electrical interference may affect the signals. Is the correct resolution selected? Set the computer so that the signals being output are compatible with the projector.
Page 197: Image Colors Are Not Right
Problem Solving Check Remedy Is the display range restricted by Blanking? Appropriately set Blanking in the configuration menu. s Signal - Blanking p.146 Is the image position adjusted correctly? (Only when projecting analog RGB signals input from the Computer port) Press the [Auto] button on the remote control or the [ ] button on the control panel to adjust the position.
Page 198: Images Appear Dark
Problem Solving Check Remedy Are the color saturation and tint adjusted correctly? Adjust the Color Saturation and Tint settings from the Configuration menu. s Image - Color Saturation, Tint p.143 Is the brightness of the room appropriate? If the room is darker than when the auto adjustment was performed, the tint of the projected images may not be displayed correctly.
Page 199: Problems When Projection Starts
• During Color Matching: 0201 Measurement value error; 0202 Measurement failure; 0203 Switch camera failure For more details, contact your local dealer or the nearest address provided in the Epson Projector Contact List. Epson Projector Contact List Problems when Projection Starts...
Page 200: Other Problems
Problem Solving Check Remedy Is the Control Panel Lock set to Full Lock? Press the [ ] button on the remote control. If you do not want to use Control Panel Lock, change the setting to Off. s "Control Panel Lock" p.122 Is the correct setting for the remote receiver selected? Check the Remote Receiver from the Configuration menu.
Page 201: The Remote Control Does Not Work
Problem Solving The remote control does not work Check Remedy Is the remote control light-emitting area pointing towards the Point the remote control towards the remote receiver. remote receiver on the projector during operation? s "Remote control operating range" p.25 Is the remote control too far from the projector? Check the operating range.
Page 202: Nothing Appears On The External Monitor
Problem Solving Nothing appears on the external monitor Check Remedy Are images input from a port other than the Computer port or Only RGB signals from the Computer port or the BNC port can be displayed on an external monitor. BNC port? Are you projecting a split screen? Only RGB signals projected on the left screen from the Computer port or the BNC port can be displayed on an...
Page 203: The Battery That Saves Your Clock Settings Is Running Low. Is Displayed
Check Remedy The internal power supply that saves your clock settings is Contact your local dealer or the nearest address provided in the Epson Projector Contact List. Epson Projector Contact List running low. "The projector did not turn off correctly. An instantaneous voltage drop may have occurred." is displayed...
Page 204: About Event Id
About Event ID Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local dealer or the nearest address provided in the Epson Projector Contact List. Epson Projector Contact List...
Page 205 Event ID Cause Remedy 089D Key exchange failed. 0920 The internal power supply that saves your clock settings is running Contact your local dealer or the nearest address provided in the Epson Projector Contact List. low. Epson Projector Contact List...
Page 206: Maintenance
Maintenance This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.
Page 207: Cleaning
Cleaning You should clean the projector if it becomes dirty or if the quality of Attention projected images starts to deteriorate. Do not rub the lens with harsh materials or subject the lens to shocks, as it can easily become damaged. Caution When cleaning, unplug the power cable from the electric outlet.
Page 208 Cleaning Remove the air filter cover. Grip the air filter cover tab between your fingers, and pull up and remove the cover while pressing the tab. Attention If the air filter is hit too hard, it may become unusable due to deformities and cracks.
Page 209 Cleaning • If a message is frequently displayed, even after cleaning, it is time to replace the air filter. Replace it with a new air filter. s "Replacing the Air Filter" p.210 • It is recommended that you clean the air filter every 20,000 hours. Clean it more often than this if using the projector in a particularly dusty environment.
Page 210: Replacing Consumables
Replacing Consumables This section explains how to replace the air filter. Remove the air filter. Grip the tab of the air filter, and pull it straight out. Replacing the Air Filter Air filter replacement period If the message is displayed frequently even though the air filter has been cleaned, replace the air filter.
Page 211 Replacing Consumables Dispose of used air filters properly in accordance with your local regulations. Material of the frame part: Polypropylene Material of the filter part: Polypropylene...
Page 212: Image Maintenance
Image Maintenance Press the [Menu] button while projecting. Color Calibration Select Color Calibration from Extended. Automatically adjusts aging deterioration of the color tone for the whole screen based on the default color settings. Select Start Auto Adjustment, and then press the [ ] button.
Page 213: Panel Alignment
Image Maintenance Panel Alignment Adjusts the pixel color shift for the LCD panel. You can adjust the pixels horizontally and vertically by 0.25 pixel within a range of ±1 pixel. • Image quality may decline after performing LCD alignment. • Images for pixels that extend beyond the edge of the projected screen are not displayed.
Page 214 Image Maintenance Select a combination of R (red), G (green), and B (blue) for the grid color. R/G/B: Displays a combination all three colors; red, green and blue. The actual color of the grid is white. R/G: This is available when R is selected from Select Color. Displays a combination of two colors;...
Page 215: Color Uniformity
Image Maintenance Color Uniformity: Turns color uniformity on or off. Color Uniformity Adjustment Level: There are eight levels from white, through gray, and up to black. You can adjust each level individually. Adjusts the color tone for the whole screen. Start Adjustments: Starts adjusting color uniformity.
Page 216 Image Maintenance Use the [ ] buttons to select the color you want to adjust, and then use the [ ][ ] buttons to adjust. Press the [ ] button to weaken the color tone. Press the [ ] button to strengthen the color tone.
Page 217: Appendix
Appendix...
Page 218: Monitoring And Controlling
Use the following procedure to display the Epson Web Control screen. Make sure your device and projector are ready for the network connection. If your Web browser is set up to connect via a proxy server, the Epson Web Control screen cannot be displayed. To display Web Control, you need to make settings so that a proxy server is not used for a connection.
Page 219: Basic Control Screen
Monitoring and Controlling Connect by entering the address of the connected projector in the • When performing the functions from the Home screen, you URL field of the Web browser. may be prompted to enter the user name and password. The Home screen is displayed.
Page 220: Osd Control Pad Screen
Monitoring and Controlling Moves to the Home screen. Displays and closes the Configuration menu. Moves to the Home screen. You can operate the Configuration menu using your finger or mouse. Turns the projector on. Flick to select an item, and tap to confirm the selection. Switches to the target image.
Page 221: Lens Control Screen
Monitoring and Controlling Focus/Distortion Operation Screen Items in the Configuration menu that cannot be set in Epson Web Control are listed below. • Signal menu - EDID, DDC Buffer • Settings Menu - User Button • Extended menu - Display - Message Position •...
Page 222 Monitoring and Controlling Moves the lens position to the home position if you press the OK button in the confirmation screen. Displays the horizontal image position. You can directly specify the position by tapping it and entering a number. Test Pattern Operation Screen Move the slider to adjust the zoom.
Page 223: Status Information Screen
Monitoring and Controlling Moves to the Home screen. Loads a memory. Displays the item name. Saves a memory. Displays the status of each item. Displays a list of memories. Selects a category from the following. Erases a memory. Status Information, Source, Signal Information, Network Wired, Network Changes a memory name.
Page 224 - When using the built-in camera (Tiling, Screen Matching, Color Calibration) - Lens Calibration - The Message Broadcasting feature in the Epson Projector Management software • The following functions are canceled when using the remote camera Displays the image you shot.
Page 225 You can set up to 32 single-byte alphanumeric characters for the Enter the IP address of the projector in the address input box of password (* : and spaces cannot be used). the browser to connect to the Epson Web Control screen.
Page 226: Setting A Certificate Using A Web Browser
Monitoring and Controlling Select Remote Camera Access. • Adjust the exposure as necessary. If you make any When the login screen is displayed, enter your user name and adjustments, shoot again and check the adjusted image. password. (The user name is EPSONWEB; the default password is •...
Page 227: Using The Mail Notification Function To Report Problems
Monitoring and Controlling Enter the IP address of the projector in the address input box of Using the Mail Notification Function to Report the browser to connect to the Epson Web Control screen. Problems The Epson Web Control screen is displayed.
Page 228: Management Using Snmp
Monitoring and Controlling The details of the problem are listed line by line. The main message Management Using SNMP contents are listed below. • Clean Air Filter By setting SNMP to On in the Configuration menu, notification messages are sent to the specified computer when a problem or warning occurs. This •...
Page 229: Cable Layouts
Add a Carriage Return (CR) code (0Dh) to the end of each command and transmit. Signal Name Function For more details, contact your local dealer or the nearest address provided in the Epson Projector Contact List. Signal wire ground Epson Projector Contact List Transmit data Receive data Communications protocol •...
Page 230: About Pjlink
• Stop-bit: 1 bit • Flow control: None DVI-D HDMI About PJLink SDI (EB-L1755U/EB-L1750U/EB- L1505UH/EB-L1500UH only) PJLink was established by the JBMIA (Japan Business Machine and Information System Industries Association) as a standard protocol for HDBaseT controlling network-compatible projector's as part of their efforts to standardize projector control protocols.
Page 231: Operating A Projector From Your Computer
• You can only enter single-byte alphanumeric characters and symbols. • The following functions cannot be used while using Crestron ® RoomView s "Changing Settings Using a Web Browser (Epson Web Control)" p.218 The Message Broadcasting feature in the Epson Projector Management software •...
Page 232 Monitoring and Controlling Button Function Button Function A/V Mute Turns the video and audio on or off. Performs the same operation as the [ ] button on the s "Hiding the Image and Sound Temporarily (A/V remote control. Mute)" p.110 s "Remote Control"...
Page 233 Monitoring and Controlling Item Function DHCP Select the Enabled check box to use DHCP. You cannot enter an IP address if DHCP is enabled. IP Address Enter the IP address to assign to the currently connected projector. Enter a subnet mask for the currently connected Subnet Mask projector.
Page 234 Monitoring and Controlling Item Function New Password Enter the new password when changing the password to open the operation window. (The name can contain up to 26 single-byte alphanumeric characters.) Confirm Enter the same password as you entered in New Password.
Page 235: Art-Net
Monitoring and Controlling Art-Net Art-Net is an Ethernet communication protocol based on the TCP/IP protocol. You can control the projector by using a DMX controller or an application system. Channel definitions The following explains the channel definitions used when controlling the projector in Art-Net. Chan- Function Operation...
Page 236 Monitoring and Controlling Chan- Function Operation Parameters Default Operation Content Lens position Non-operational 0 - 31 Moves the lens shift to the home position. Move to home position 32 - 63 Non-operational 64 - 255 Horizontal lens shift (+) lens adjustment Movement - Large 0 - 31 Performs horizontal lens shift using the amount of movement specified.
Page 237 Monitoring and Controlling Chan- Function Operation Parameters Default Operation Content (-) lens adjustment Movement - Small 160 - 191 Movement - Me‐ 192 - 223 dium Movement - Large 224 - 255 Electronic focus (+) lens adjustment Movement - Large 0 - 31 Performs electronic focus using the amount of movement specified.
Page 238 Monitoring and Controlling Chan- Function Operation Parameters Default Operation Content Load lens memory 4 64 - 79 Load lens memory 5 80 - 95 Load lens memory 6 96 - 111 Load lens memory 7 112 - 127 Load lens memory 8 128 - 143 Load lens memory 9 144 - 159...
Page 239 Monitoring and Controlling While controlling the projector using Art-Net and performing operations from the remote control or control panel, settings made by the DMX controller or application software may differ from the actual projector's status. When you want to apply all the channel controls to the projector, set Channel 13 to "Cannot control", then set it back to "Can control".
Page 240: Optional Accessories And Consumables
Special expertise is required to suspend the projector from a ceiling. Contact Computer cable ELPKC02 your local dealer or the nearest address provided in the Epson Projector (1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin) Epson Projector Contact List Contact List.
Page 241: Screen Size And Projection Distance
Screen Size and Projection Distance Unit: cm Projection Distance for EB-L1755U/EB-L1750U/EB- L1505UH/EB-L1500UH 4:3 Screen Size Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top 60" 122x91 226 to 370 -101 to +9 80" 163x122 304 to 497 -134 to +12 100"...
Page 242: Elplx02
Screen Size and Projection Distance Unit: cm 4:3 Screen Size Minimum (Wide) to Vertical Lens Shift 16:10 Screen Size Maximum (Tele) Bottom to Top Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top 440" 894x671 519 to 624 -497 to -174 60"...
Page 243: Elplu04/Elplu02
Screen Size and Projection Distance 16:10 Screen Size 16:9 Screen Size Minimum (Wide) to Vertical Lens Shift Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top Maximum (Tele) Bottom to Top 500" 1077x673 521 to 626 -499 to -175 200"...
Page 244: Elplw06/Elplw04
Screen Size and Projection Distance 4:3 Screen Size 16:10 Screen Size Minimum (Wide) to Vertical Lens Shift Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top Maximum (Tele) Bottom to Top 120" 244x183 224 to 313 -135 to -47 120"...
Page 245: Elplm10/Elplm06
Screen Size and Projection Distance Unit: cm ELPLM10/ELPLM06 Unit: cm 16:9 Screen Size Minimum (Wide) to Vertical Lens Shift 4:3 Screen Size Maximum (Tele) Bottom to Top Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top 60" 133x75 154 to 212 -87 to +13 60"...
Page 246: Elplm11/Elplm07
Screen Size and Projection Distance Unit: cm Unit: cm 16:10 Screen Size 16:9 Screen Size Minimum (Wide) to Vertical Lens Shift Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top Maximum (Tele) Bottom to Top 60" 130x81 306 to 473 -89 to +8 60"...
Page 247: Elpll08/Elpll07
Screen Size and Projection Distance Unit: cm ELPLL08/ELPLL07 Unit: cm 16:10 Screen Size Minimum (Wide) to Vertical Lens Shift 4:3 Screen Size Maximum (Tele) Bottom to Top Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top 60" 130x81 664 to 941 -89 to +8 60"...
Page 248: Projection Distance For Eb-L1715S/Eb-L1710S/Eb-L1515S/Eb-L1510S
Screen Size and Projection Distance Unit: cm Projection Distance for EB-L1715S/EB-L1710S/EB- 16:9 Screen Size L1515S/EB-L1510S 60" 133x75 80" 177x100 100" 221x125 120" 266x149 150" 332x187 200" 443x249 -125 250" 553x311 -156 440" 974x548 -274 Unit: cm 16:10 Screen Size 60" 130x81 80"...
Page 249: Elplx02
Screen Size and Projection Distance Unit: cm Unit: cm 4:3 Screen Size 16:10 Screen Size Minimum (Wide) to Vertical Lens Shift Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top Maximum (Tele) Bottom to Top 60" 122x91 193 to 318 -96 to +5 60"...
Page 250: Elplu04/Elplu02
Screen Size and Projection Distance 4:3 Screen Size 16:10 Screen Size Minimum (Wide) to Vertical Lens Shift Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top Maximum (Tele) Bottom to Top 200" 406x305 201 to 242 -201 to -104 200"...
Page 251: Elplw05
Screen Size and Projection Distance ELPLW05 Unit: cm 16:9 Screen Size Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top 4:3 Screen Size 100" 221x125 145 to 176 -154 to +29 Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top 120"...
Page 252: Elplw06/Elplw04
Screen Size and Projection Distance Unit: cm Unit: cm 16:10 Screen Size 16:9 Screen Size Minimum (Wide) to Vertical Lens Shift Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top Maximum (Tele) Bottom to Top 60" 129x81 98 to 140 -56 to -25 60"...
Page 253: Elplm10/Elplm06
Screen Size and Projection Distance Unit: cm ELPLM10/ELPLM06 Unit: cm 16:10 Screen Size Minimum (Wide) to Vertical Lens Shift 4:3 Screen Size Maximum (Tele) Bottom to Top Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top 60" 129x81 316 to 490 -94 to +13 60"...
Page 254: Elpll08/Elpll07
Screen Size and Projection Distance Unit: cm ELPLL08/ELPLL07 Unit: cm 16:9 Screen Size Minimum (Wide) to Vertical Lens Shift 4:3 Screen Size Maximum (Tele) Bottom to Top Minimum (Wide) to Vertical Lens Shift Maximum (Tele) Bottom to Top 60" 133x75 472 to 730 -92 to +17 60"...
Page 255: Elplr04
Screen Size and Projection Distance Unit: cm Unit: cm 16:9 Screen Size 16:10 Screen Size Minimum (Wide) to Vertical Lens Shift 60" 133x75 Maximum (Tele) Bottom to Top 80" 177x100 60" 129x81 685 to 973 -94 to +13 100" 221x125 80"...
Page 256: Polarizer (Elppl01) Installation Distance (Eb-L1505Uh/Eb-L1500Uh/Eb-L1515S/Eb L1510S Only)
Screen Size and Projection Distance Polarizer (ELPPL01) Installation Distance (EB- L1505UH/EB-L1500UH/EB-L1515S/EB-L1510S Only) Possible installation range of the polarizer Shortest distance from the projection lens to the polarizer Longest distance from the projection lens to the polarizer Polarizer (ELPPL01) Units: mm Lens type ELPLW06/ELPLW04 ELPLM15/ELPLM09/...
Page 257: Adjustment Range For Projected Images
Adjustment Range for Projected Images EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH H/V-Keystone Horizontally curved surface (concave) "H/V-Keystone" p.66 Lens type Vertical Horizontal Screen Center of the circle of which the ELPLM15/ELPLM09/ -44˚ to 44˚ -30˚ to 30˚ ELPLS04 curved surface is an arc Projection distance ELPLX02 -16˚...
Page 258 Adjustment Range for Projected Images Horizontally curved surface (convex) Vertically curved surface (concave) Screen Screen Center of the circle of which the Center of the circle of which the curved surface is an arc curved surface is an arc Projection distance Projection distance Radius of the circle of which the Radius of the circle of which the...
Page 259 Adjustment Range for Projected Images Vertically curved surface (convex) EB-L1715S/EB-L1710S/EB-L1515S/EB-L1510S Horizontally curved surface (concave) Screen Center of the circle of which the Screen curved surface is an arc Center of the circle of which the Projection distance curved surface is an arc Radius of the circle of which the Projection distance curved surface is an arc...
Page 260 Adjustment Range for Projected Images Horizontally curved surface (convex) Vertically curved surface (concave) Screen Screen Center of the circle of which the Center of the circle of which the curved surface is an arc curved surface is an arc Projection distance Projection distance Radius of the circle of which the Radius of the circle of which the...
Page 261: Corner Wall
Adjustment Range for Projected Images Vertically curved surface (convex) Corner Wall "Corner Wall" p.72 Screen Center of the circle of which the The α in the figure is the maximum angle in which the projector can move. curved surface is an arc See the table below for detailed values.
Page 262 Adjustment Range for Projected Images EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH Convex horizontal corner correction (correction to bilateral symmetry by using corners as the center line) Concave horizontal corner correction (correction to bilateral symmetry by using corners as the center line) Screen Screen α Angle of possible projector motion α...
Page 263 Adjustment Range for Projected Images Concave vertical corner correction (correction to horizontal symmetry by Convex vertical corner correction (correction to horizontal symmetry by using corners as the center line) using corners as the center line) Screen Screen α Angle of possible projector α...
Page 264 Adjustment Range for Projected Images EB-L1715S/EB-L1710S/EB-L1515S/EB-L1510S Convex horizontal corner correction (correction to bilateral symmetry by using corners as the center line) Concave horizontal corner correction (correction to bilateral symmetry by using corners as the center line) Screen Screen α Angle of possible projector motion α...
Page 265 Adjustment Range for Projected Images Concave vertical corner correction (correction to horizontal symmetry by Convex vertical corner correction (correction to horizontal symmetry by using corners as the center line) using corners as the center line) Screen Screen α Angle of possible projector α...
Page 266: Supported Monitor Displays
Supported Monitor Displays EB-L1755U/EB-L1750U/EB-L1505UH/EB-L1500UH When the resolution of the input signals is larger than the projector's panel resolution, the image quality may decline. Signals with a check mark are supported. Signal Signal Resolution V Sync Computer/BNC HDMI HDBaseT DVI-D Type...
Page 267 Supported Monitor Displays Signal Signal Resolution V Sync Computer/BNC HDMI HDBaseT DVI-D Type Format (Dot) (Hz) YCbCr YCbCr (8bit) YCbCr (8bit) YCbCr (8bit) (8bit) (8bit) (8bit) 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 WXGA++ 1600 SXGA 1152 1280 1280 1024 SXGA+ 1400...
Page 268 Supported Monitor Displays Signal Signal Resolution V Sync Computer/BNC HDMI HDBaseT DVI-D Type Format (Dot) (Hz) YCbCr YCbCr (8bit) YCbCr (8bit) YCbCr (8bit) (8bit) (8bit) (8bit) 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 HDTV (720p) 1280 59.94 HDTV (1080i) 1920 1080 59.94...
Page 269 Supported Monitor Displays Signal Signal Resolution V Sync Computer/BNC HDMI HDBaseT DVI-D Type Format (Dot) (Hz) YCbCr YCbCr (8bit) YCbCr (8bit) YCbCr (8bit) (8bit) (8bit) (8bit) 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 59.94 *1 Based on VESA CVT-RB (Reduced Blanking) *2 Only when Wide is selected in Resolution from the Signal menu.
Page 270: Eb-L1715S/Eb-L1710S/Eb-L1515S/Eb-L1510S
Supported Monitor Displays Mode Signal Resolution V Sync Format (Dot) (Hz) YCbCr Level (10bit) 4:2:2 59.94 EB-L1715S/EB-L1710S/EB-L1515S/EB-L1510S When the resolution of the input signals is larger than the projector's panel resolution, the image quality may decline. Signals with a check mark are supported. Signal Signal Resolution...
Page 271 Supported Monitor Displays Signal Signal Resolution V Sync Computer/BNC HDMI HDBaseT DVI-D Type Format (Dot) (Hz) YCbCr YCbCr (8bit) YCbCr (8bit) YCbCr (8bit) (8bit) (8bit) (8bit) 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 1280 1366 WXGA+ 1440 WXGA++ 1600 SXGA 1152 1280...
Page 272 Supported Monitor Displays Signal Signal Resolution V Sync Computer/BNC HDMI HDBaseT DVI-D Type Format (Dot) (Hz) YCbCr YCbCr (8bit) YCbCr (8bit) YCbCr (8bit) (8bit) (8bit) (8bit) 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 4:2:0 4:4:4 4:2:2 SDTV (480i) 59.94 SDTV (576i) SDTV (480p) 59.94 SDTV (576p) HDTV (720p)
Page 273: Specifications
Specifications Projector General Specifications EB-L1755U EB-L1505UH EB-L1715S EB-L1515S Product name EB-L1750U EB-L1500UH EB-L1710S EB-L1510S 586 (W) x 185 (H) x 492 (D) mm (not including raised section) Dimensions 1.03" Wide 1.06" LCD panel size Polysilicon TFT active matrix Display method...
Page 274 Specifications Rated power consumption: Rated power consumption: Rated power consumption: Rated power consumption: 220 to 240 V area 1024 W 908 W 1024 W 908 W Standby power consumption Standby power consumption Standby power consumption Standby power consumption (Communication On): 2.0 W (Communication On): 2.0 W (Communication On): 2.0 W (Communication On): 2.0 W...
Page 275 Specifications EB-L1755U EB-L1505UH EB-L1715S EB-L1515S Product name EB-L1750U EB-L1500UH EB-L1710S EB-L1510S Mini D-Sub15-pin (female) blue Connec- Computer Port tors Audio1 port Stereo mini jack (3.5Φ) 5BNC (female) BNC port Audio2 port Stereo mini jack (3.5Φ) DVI-D 24pin Single link HDCP compatible...
Page 276 Specifications This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Page 277 CPU Boards and Power Supplies used with Class B Personal Computers Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference Epson America, Inc. in a residential installation. This equipment generates, uses, and can radiate Located at:...
Page 278: Appearance
Appearance Units: mm Center of lens Distance from center of lens to suspension bracket fixing point...
Page 279: Glossary
Adjusting this particular property of an image is called contrast adjustment. Control4 SDDP is a technology developed by Control4 to allow Control4 control systems to acquire device information for the projector. Epson have Control4 Simple Device implemented this protocol technology, and have provided a setting to enable the protocol function (ON).
Page 280 Glossary A number to identify a computer connected to a network. IP Address Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount Progressive of flicker in images decreases because the volume of information has doubled compared with an interlace system.
Page 281: General Notes
Windows 10 operating system Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the In this guide, the operating systems above are referred to as "Windows purchaser or third parties as a result of: accident, misuse, or abuse of this product or Vista", "Windows 7", "Windows 8", "Windows 8.1", and "Windows 10".
Page 282 HDBaseT Alliance logo are trademarks of the HDBaseT Alliance. Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks. ©SEIKO EPSON CORPORATION 2017. All rights reserved.
Page 283: List Of Safety Symbols Compliant With Iec60950-1 A2
List of Safety Symbols Compliant with IEC60950-1 A2 The following table lists the meaning of the safety symbols labeled on the Symbol mark Approved Meaning equipment. standards IEC60417 Battery, general Symbol mark Approved Meaning No. 5001B On battery powered equipment. To standards identify a device for instance a cover for IEC60417...
Page 284 List of Safety Symbols Compliant with IEC60950-1 A2 Symbol mark Approved Meaning standards ISO 3864 General prohibition To identify actions or operations that are prohibited. ISO 3864 Contact prohibition To indicate injury that could occur due to touching a specific part of the equipment. Never look into the projection lens while the projector is on.
Page 285: Index
How to replace the air filter ..... 210 Cinema ............77 Edge Blending ........97, 154 Cleaning ............207 EDID ........... 147, 193 Cleaning the air filter and air intake vent Epson Projector Management ....218 ................ 207 Image Menu ..........143 Epson Web Control ........218...
Page 286 Index Indicators ............ 178 Rear feet ............19 Info menu ........... 165 Refresh Rate ..........165 Operating Temperature ......274 Input Signal ..........165 Remote control ..........21 Operation ............ 151 Installation requirements ......30 Remote control button lock ..... 123 Optional accessories ........
Page 287 Index Specifications ..........273 Wired LAN menu ........162 Split Screen ..........148 Wireless LAN menu ........158 Split Screen Setup ........108 Standby Mode ..........153 Startup Screen ..........150 Status ............166 Status indicators ........... 16 Storage temperature ........274 Subnet Mask ........

This manual is also suitable for:

Eb-l1505uh Eb-l1500uh Eb-l1715s Eb-l1710s Eb-l1750u Eb-l1515s ... Show all

Epson EB-L1755U User Manual

Quick Links

Related Manuals for Epson EB-L1755U

Summary of Contents for Epson EB-L1755U